Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Nice TTDRGB
Summary of Contents for Nice TTDRGB
- Page 1 TTDRGB LED control range EN - Instructions and warnings for installation and use...
-
Page 2: Table Of Contents
GENERAL SAFETY WARNINGS AND ENGLISH PRECAUTIONS Translation of the original instructions in full GENERAL SAFETY WARNINGS AND PRECAUTIONS WARNING! Important safety instructions. Observe all the instructions as improper installation may cause serious damages. CONTENTS WARNING! Important safety instructions. It is important to comply with these instructions to ensure personal GENERAL SAFETY WARNINGS AND PRECAUTIONS . -
Page 3: Product Description And Intended Use
“Figure 2”. bidden! LIST OF CONSTITUENT PARTS The TTDRGB is made up of a casing that protects the command and control boards. “Figure 1” shows the main parts making up the TTDRGB. Tc point A Connection to the LED strips B Connection to the 24Vdc power supply unit ENGLISH –... -
Page 4: Product Installation
PRODUCT INSTALLATION ELECTRICAL CONNECTIONS To fasten TTDRGB (“Figure 3”): To make the electrical connections: – connect the cable (A) to the chosen 24Vdc power supply unit position the box (A) and fasten it with bi-adhesive tape (B) (not – connect the connector (B) to the LED strips. -
Page 5: Transmitter Pairings
TRANSMITTER PAIRINGS The functions and programming modes described below must be made with a transmitter paired (memorised) with the system. (= 5s) 5.2.1 MEMORISING THE FIRST TRANSMITTER (x 1) 5.2.1.1 TWO-WAY mode 5 sec RAPID PROCEDURE (only for memorising the first transmitter) To memorise the first transmitter (“Figure 6”): disconnect the power supply to the system. - Page 6 To memorise the transmitter (“Figure 9”): 5.2.2.3 ONE-WAY mode and transmitters lacking the “PRG” on the OLD transmitter: press and release the PRG key. The LED and “ESC” keys strip will flash twice To memorise the transmitter (“Figure 11”): on the NEW transmitter: press and hold the STOP key for 5 s on the NEW transmitter: press the key for 7 s then release it.
-
Page 7: Locking And Unlocking The Memory
5.4.1 DELETION PROCEDURES (WITH MEMORISED LOCKING AND UNLOCKING THE MEMORY TRANSMITTER) Activating the memory lock allows for preventing the accidental and ran- RAPID PROCEDURE (only for deleting ALL SETTINGS) dom memorisation of other unintended or unauthorised transmitters. To do this (“Figure 13”): To do this (“Figure 12”): disconnect the power supply to the system. -
Page 8: Deletion Procedures (With Non-Memorised Transmitter In One-Way Mode)
5.4.2 DELETION PROCEDURES (WITH NON-MEMORISED 5.4.3 PRE-DEFINED (PRESET) OR PERSONALISED (CUSTOM) TRANSMITTER IN ONE-WAY MODE) COLOURS The system leaves the factory (PRESET) with 8 pre-configured and avail- In TWO-WAY mode, follow the procedure indicated in able colours. Activating the “CUSTOM” function allows for memorising the paragraph “Memorising the FIRST TRANSMITTER”, personalised colours which can then be recalled. -
Page 9: Rotation Speed Of The Rgb Colours
5.4.4 ROTATION SPEED OF THE RGB COLOURS COMMANDS FROM THE TRANSMITTER This function allows for varying the rotation speed of the RGB LED strip colours. To activate rotation of the colours, refer to the “COMMANDS COMMANDS FROM THE TRANSMITTER FROM THE TRANSMITTER” chapter. The table shown below summarises the keys to be pressed on the trans- mitter for sending the main commands to the system. -
Page 10: Product Maintenance
PRODUCT MAINTENANCE TTDRGB the electronic part does not require any special maintenance. functions and intended use. In any case, every 6 months the system should be checked to ensure the entire system is working efficiently. - Page 11 NOTES ENGLISH – 11...
- Page 12 Nice SpA Via Callalta, 1 31046 Oderzo TV Italy www.niceforyou.com info@niceforyou.com...