Advertisement
Quick Links
Advertisement
Related Manuals for Axminster MJ12-2600 II
Summary of Contents for Axminster MJ12-2600 II
- Page 1 Instruction Manual Sliding Panel Saw Model No.: MJ12-1600II/2000 II /2600 II /2800 II /3200 II...
- Page 2 Install the Sliding panel assembly TROUBLESHOOTING Adjust the sliding panel level PARTS LIST & DIAGRAMS Install the cross cut table Install the cross cut fence SPECIFICATIONS Model MJ12-1600II MJ12-2000 II MJ12-2600 II MJ12-2800 II MJ12-3200 II Motor power 230V~,50HZ,3000W 230V~,50HZ,3000W 230V~,50HZ,3000W 230V~,50HZ,3000W 230V~,50HZ,3000W 400V,3~,50HZ,4000W...
- Page 3 SAFETY should be in accordance with amperage rating. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Your extension cord must also contain a ground wire. Always repair or replace extension cords if they For Your Own Safety, Read Instruction Manual become damaged.
- Page 4 Additional Safety Instructions for Panel Saws No list of safety guidelines can be complete. Every shop environment is different. Always consider safety first, as it applies to your 1. SAFETY ACCESSORIES. Always use the blade individual working conditions. Use this and guard and riving knife on all ''through-sawing'' other machinery with caution and respect.
- Page 5 SITE CONSIDERATIONS General Condition: 1 .Electrical connection: Steady state voltage: 0.9-1.1 of nominal voltage. Frequency: 0.99-1.01 of nominal frequency continuously; 0.98-1.02 short time The mains connection must have maximum16A fuse. Electrical supply which has protection devices of under-voltage, over-voltage, over-current as well as a residual current device (RCD) which maximum residual current rated at 0.03A.
- Page 7 A. Crosscut Table-Provides a wide, stable platform for K. Blade Angle Hand-wheel-Adjust the angle of the supporting full-size panels during crosscutting saw blades. operations. L. Mitre Gauge-This gauge aligns the wood for a B. Flip Stops-Used for quick measurements for cross-cut.
- Page 8 UNPACKING Clean Up The Sliding Panel Saw is shipped from the manufacturer in a carefully packed crate. If you The unpainted surfaces are coated with a light oil to discover the machine is damaged after you have protect them from corrosion during shipment. Remove signed for delivery, please call Customer Service this protective coating with a solvent cleaner or citrus- immediately for advice.
- Page 9 Center the extension table over the edges and tap it. ASSEMBLY Check the surface alignment. Moving & Placing Saw Base Unit The Sliding Panel Saw is a heavy machine. Serious personal injury may occur if safe moving methods are not followed. To be safe, you will need assistance and power equipment when moving the shipping crate and removing the machine from the crate.
- Page 10 Install the main blade elevation & angle handwheel 1. Fitting the elevation handwheel(1) and angle handwheel (2) onto the elevation and angle shaft. Install the rip fence rail Screw the blade lock knob(3) onto the elevation Handwheel. 1. insert 4-M10x80 hex head bolts into major table and extension tables.
- Page 11 2 .Place the cross-cut table support (A) onto the swing arm assembly, and hand tighten the lock nuts. The Adjust the sliding panel level: support needs further adjustment. 1 . Place a level rule (cross cut fence) on to major table Install the Sliding panel assembly and sliding panel.
- Page 12 Install the cross cut fence Install the dust port Place dust port onto bottom rear panel, 1.Drop the cross cut fence into the forward or rear guide tighten it with 4 M6x12 pan head screws washers and pin hole. nuts (nuts inside stand). 2.Tighten the knurled nut.
- Page 13 Install dust hoses 1. Install the 2" dust hose onto the blade guard with 2" hose clamp. 2. Put the 2" dust hose onto dust hose support, keep free with the working table. 3. Another end of 2" dust hose clamps to the main dust port on the bottom of rear panel.
- Page 14 REPLACEMENT & ADJUSTMENT Replace the main blade Disconnect the saw from the power source! The main blade dimension suitable for MJ12B machine is 254x30x3( outer diameter, core diameter, thickness), 305x30x3, 315x30x3mm. Replace and adjusting the scoring blade But any time you change blade thickness, the appropriate sized riving knife and scoring blade must also be changed to match the size of main Disconnect the saw from the power source!
- Page 15 To align scoring blade: Loosen the clamping screw (A). Lateral adjustment is made via adjusting screw (B). the height setting is made via setting screw (C). retighten the clamping screw (A). Adjust the scoring blade laterally so it is in line with the main saw-blade.
- Page 16 2. Raise the main blade up as far as it will go. 3. Mark the center of the blade with a felt tip pen. This will allow you to take your measurements from the exact same place on the blade. 4.
- Page 17 OPERATIONS 3. Install the crosscut fence in the guide pin holes and lock it in place with the knurled nut. Note First, drop the crosscut fence into the forward guide pin hole, turn the "Z"lock plate to align the fence, then tighten the knurled nut. Your safety is important.
- Page 18 This machine has the capability of crosscutting workpieces while using the hold down w/mitre gauge . 5. Mount the hold down arm onto the stud and lock the work-piece in place. 6. Once all the necessary safety precautions have been taken, perform the cutting operation.
- Page 19 Miter Cutting Note If the workpiece extends to the left of the saw blade more than 1200mm, then the crosscut fence The cross cut table built two scales for forward and rear slide needs to be extended. mount fence to perform mitre cut. 4.
- Page 20 ELECTRICAL MAINTENANCE Main switch This machine is equipped with a knee touch no-volt release main switch and a limit switch. Always disconnect power to the machine before The main switch is equipped a large size touch panel, performing maintenance. Failure to do this may during performance cutting work, any part of man body result in serious personal injury.
- Page 21 LIMIT SWITCH ELECTRO-MAGENETIC SWITCH...
- Page 22 TROUBLESHOOTING Disconnect power to the machine when performing any troubleshooting. Failure to do this may result in serious personal injury.
- Page 23 PARTS LIST & DIAGRAMS Parts List Diagram A Description Description Pan head screw M6x12 A-28 Washer 4mm Washer 6mm A-29 Pan head screw M4x12 Dust port A-30 Hold screw, push stick Right panel, saw base A-31 Push stick A-15 Washer 5mm A-32 Internal guard A-18...
- Page 24 Parts List Diagram B cont... Description Description Lower support B-43 B-71 Hex nut M10 Adjustable disc B-44 B-72 Lock guide Scew guide B-51 B-73 T-nut, push handle Taping screw ST4.2x12 B-52 B-74 Set screw M8x12 End cap, sliding panel B-53 B-75 Insert, ball frame Allen screw M5x8...
- Page 25 Parts List Diagram C cont... Description Description Description C-49 Ball bearing C-79 Hex head screw M6X20 C-134 locking wheel C-50 Tube C-80 Allen screw M6X20 C-135 nylon shaft C-51 Wheel handle C-81 Hex nut M6 C-136 sunk screw m6*25 C-52 Thread C-82 Set screw M8X8...
- Page 26 Parts List Diagram E Description Description E-42 Hex screw M8x30 Scale, cross cut table E-43 Hex screw M10x25 Washer 6mm E-44 Sunk head screw M6x12 Scale, cross cut table E-45 T-nut, extension fence Allen screw M6x12 E-46 Lock plate Eccentric cam E-47 T-block Washer 8mm...
- Page 27 Parts List Diagram G Description Description G-20 Dust hose support Rear extension table G-21 Washer 6mm Washer 8mm G-22 Hex screw M6x20 Hex nut M8 G-23 Hex nut M6 Set screw M6x12 G-26 Adjustable disc Hex screw M8x16 G-27 Lower, support Flat washer 10mm G-28 Disc insert...
- Page 36 Parts List Diagram K Description Description Cross head screw M5X8 Left guard K-1. K-3. Washer M5 Right guard K-2. K-4.
Need help?
Do you have a question about the MJ12-2600 II and is the answer not in the manual?
Questions and answers