Control Panel - Friedrich CEW18B33A Service Manual

Control Panel

USING YOUR AIR CONDITIONER
Electronic Control Panel & Remote Control
NOTE: This display always shows the room temperature in Fan
Mode except when setting the Timer.
For Cooling model
For Heating model
Normal Operating Sounds
•
You may hear a pinging noise caused by water
hitting the condenser on rainy days, or when the
humidity is high. This design feature helps re­
move moisture and improve efficiency.
•
You may hear the thermostat click when the com­
pressor cycles on and off.
•
Water will collect in the base pan during rain or
days of high humidity. The water may overflow
and drip from the outside part of the unit.
•
The fan may run even when the compressor is
not on.
Digital Display:
1.
temperature will be displayed.
Time will be displayed under the timer setting.
2. + and - Button:
control panel and remote to increase or decrease
the Set Temperature or Timer.
Temperature range: 61"F~88"F or 16'C~31 'C.
@
3.
Mode Button:
4.
through the various modes: Cool, Dry, Fan and
Auto, or Heat.
12
OPERATION
I
TEMP/HR.
+
:
: � : : :
'?
: : ·
;
1
1
l
'"
0
MONEY
MODE
TIM R
:
9 8 7 6 5 4
1
I
TEMP/HR.
+
:
:
: : : l
: : ·
'?
;
1 1
�
'" 0
MONEY
MODE
TIM R
:
9 8 7 6 5 4
Air Conditioner Controls
Without timer setting, the set
Use these buttons on the
Button: Turn the air conditioner on and off.
Press the mode button to cycle
Cool Mode:
conditioner to cool the room and at the same time
reduces air humidity. Press the MODE button to
activate the cooling function. To optimize the
function of the air conditioner, adjust the
temperature and the speed by pressing the button
indicated.
>
Dry Mode:
the air to make the room more comfortable. Press
2
MODE button to set the DRY mode. An automatic
function of alternating cooling cycles and air fan
3
is activated.
Fan Mode:
ventilation. Press MODE button to set the FAN
mode. With pressing the FAN SPEED button the
speed changes in the following sequence: Hi, Med
and Low in FAN mode.
>
Auto Mode:
chooses the fan speed and the mode of operation
2
(COOL,HEAT,DRY or FAN). In this mode the
temperature is set automatically according to the
3
room temperature (tested by the temperature
sensor which is incorporated in the indoor unit.).
Heat Mode:
conditioner to heat the room. Press the MODE
button to activate the heating function. To optimize
the function of the air conditioner, adjust the
temperature and the speed by pressing the button
indicated.
Timer Button:
5.
panel and remote to set the Timer.
Timer Off:
pressing TIMER button. Set the rest time by
pressing the button "+" or "-" until the rest
time displayed is to your liking then press
the TIMER button again.
Timer On:
button at the first time, set the temperature with
pressing the button "+" or "-" . Press TIMER
button at the second time, set the rest time with
pressing the button "+" or "-" . Press TIMER
button at the third time, confirm the setting, then
the rest time to next automatic switching-on could
be read on the display of the machine.
be set to automatically turn off or on in 0.5-24
hours. Each press of the "+" "-"
buttons will increase or decrease the timer. The
Timer can be set in 0.5 hours increment below 10
hours and 1 hour increment for 10 hours or above.
The SET light will turn on while setting.
To cancel the set function, press the TIMER
button again.
The cooling function allows the air
This function reduces the humidity of
The conditioner works in only
In AUTO mode the unit automatically
The heating function allows the air
Use these buttons on the control
The timed stop is programmed by
When the unit is off, press TIMER
Note:
It can