Operation - EINHELL 41.407.40 Operating Instructions Manual

•
So that the pump does not suffer any damage
when it is not in use, a small amount of leaka-
ge from the pump is normal.
•
Never use the machine in potentially explosi-
ve areas under any circumstances!
•
The operating temperature must be between
+5 and + 40°C.
•
Do not cover or modify the lance or the spray
nozzles in any way.
•
The pressure cleaner is designed to be used
with cold or lukewarm water (max. 40 °C); hig-
her temperatures can damage the pump.
•
Do not use water that is dirty, gritty or con-
tains any chemical products, as these could
impair operation and shorten the life of the
equipment.
Caution: Risk of explosion
Do not spray fl ammable liquids.
Warning
Water that has passed through the non-return
valve is not drinkable.
Warning
If cleaning agent gets into contact with your skin
or into your eye, rinse immediately with lots of
clean water. Then consult a doctor or follow the
steps described on the safety data sheet or provi-
ded by the manufacturer of the cleaning agent.
5.2 Assembly
5.2.1 Assembling the equipment (Fig. 4a-4c)
Assemble the pressure cleaner as shown in Figu-
re 4a-4c.
5.2.2 Fitting the gun attachments (Fig. 3)
Various attachments can be fi tted to the gun. First
fi t the extension (6) to the gun (5). Then you can
press the attachments into the extension (you will
encounter a slight spring resistance) and secure
the attachment by turning.
Important! Check that the attachment is secure
before you begin with the cleaning.
Solid cone / fl at fan lance (7)
The shape of the water jet can be changed from
solid cone to fl at fan by turning nozzle (a) (Fig. 7).
5.2.3 Connecting the high-pressure hose
(Fig. 5a-5b)
Connect the high-pressure hose (8) to the gun (5)
and to the connector for the high-pressure hose
(13).
Anl_TC_HP_90_SPK9.indb 19 Anl_TC_HP_90_SPK9.indb 19
GB
5.2.4 Water inlet connector (Fig. 6)
The connection for the water inlet (3) is equipped
with a connector (9) for standard hose coupling
systems. Plug the hose coupling on the supply
hose (min. Ø 1/2" / approx. 13 mm) to the water
inlet connector (9).
Always use a reinforced hose with a standard
coupling for the water inlet. The hose should be at
least 6 m in length. (Not supplied)
A backfl ow preventer must be installed between
the drinking water and the pressure cleaner! Ask
your local plumber about this.
5.2.5 Electrical connections
•
Before you connect the equipment to the
power supply make sure that the data on the
rating plate are identical to the supply voltage.
•
If you use any extension cables, make sure
that they are suitable for outdoor use and
have large enough wires:
1 – 10 m: 1.5 mm²
10-30m: 2.5 mm²
•
Insert the power plug on the power cable into
the socket outlet.

6. Operation

The equipment consists of an assembly with a
pump, which is encased in a shock absorbing
housing. For an optimal working position the
equipment comes with a lance and a non-slip
gun, whose shape and confi guration comply with
the applicable regulations.
6.1 Using for the fi rst time
Once you have completely assembled the pres-
sure cleaner and made all the connections, pro-
ceed as follows:
Open the water inlet. Release the safety device
(a) (Fig. 3) on the spray gun and pull back trigger
lever (b) (Fig. 3) in order to bleed the trapped air
out of the equipment.
Turn on the equipment by switching the On/Off
switch (Fig. 1/2) to "ON".
Now activate the trigger lever (b).
To turn off , release the trigger lever (b). The
equipment will then go into standby. As soon as
you press the trigger lever (b) again, the pressure
- 19 -
15.06.2020 14:09:58 15.06.2020 14:09:58