1. SAFETY INSTRUCTIONS 1. General Safety Warnings • Read these instructions carefully before using your appliance and keep this manual for future reference. Please check the packaging of your machine before installation and the outer surface of the machine once the packaging has been removed. Do not operate the machine if it appears damaged or if the packaging has been opened.
2. Installation Warnings • Choose a suitable and safe place to install your machine. • Only original spare parts should be used with the machine. Unplug the machine before installation. Your machine must only be installed by an authorised service agent. Installation by anyone other than an authorised agent may cause your warranty to be void.
pressure exceeds 1 MPa, a pressure relief valve must be fitted between the connection. 3. During Usage • This machine is for domestic use only; do not use • it for other purposes. Commercial use will void the guarantee. Do not stand, sit or place loads on the open door of the dishwasher.
Page 7
the door for one minute after it has opened. For effective drying, keep the door open for 30 minutes after a programme has ended. Do not stand in front of the door after the auto-open signal sounds. In the case of a malfunction, repair should only be performed by an authorised service company, otherwise the warranty will be void.
Page 8
CE Declaration of Conformity We declare that our products meet the applicable European Directives, Decisions and Regulations and the requirements listed in the standards referenced. Disposal of your old machine The symbol on the product or on its packaging indicates that this product may not be treated as household waste.
2. INSTALLATION WARNING: Use the new water inlet 2.1. Machine positioning hose supplied with your machine, do not use an old machine’s hose. When positioning the machine, place it in an area where dishes can be easily loaded WARNING: Run water through the and unloaded.
2.6. Fitting the machine undercounter 2.5 Electrical connection If you wish to fit your machine undercounter, there must be sufficient space to do so and WARNING: Your machine is set to the wiring-plumbing must be suitable to do operate at 220-240 V. If the mains voltage so (1).
Page 11
Products Product’s Height (±2 mm) 820 mm 825 mm 835 mm A: If there is no felt on the top of the product; you should take into account this product’s height. B1: If there is felt on the top of the product with 2nd basket;...
3. TECHNICAL SPECIFICATIONS 3.2. Technical specifications 10 place Capacity settings Dimensions (mm) Height 850(mm) Width 450(mm) Depth 598(mm) Net weight 40 kg Operating 220-240V voltage / 50 Hz, frequency Total current 10(A) 3.1. General appearance 1. Worktop Total power 2. Upper basket with racks 1900(W) 3.
4. BEFORE USING THE APPLIANCE 4.1. Preparing your dishwasher for first use • Make sure the electricity and supply water specifications match the values indicated in the installation instructions for the machine. • Remove all packaging material inside the machine. •...
4.4. Test Strip Run water through Keep the strip in Set the hardness level of Shake the strip. Wait (1min.) the tap (1min.) the water (1sec) your machine. second munite munite NOTE: The factory hardness level setting is “3”. If the water is well water or has a hardness level above 90 dF, we recommend that you use filter and refinement devices.
Do not fill detergent into the detergent setting set too low, whitish stains remains compartment more than required; otherwise on dishes and dishes do not dry and you can see whitish streaks or bluish layers washed clean. If rinse aid dosage setting on glass and dishes and may cause glass set too height, you can see bluish layers on corrosion.
5. LOADING YOUR WARNING: To avoid any possible DISHWASHER injuries, place long-handle and sharp- pointed knives with their sharp points facing down or horizontally on the baskets. For best results, follow these loading guidelines. Loading the household dishwasher up to the capacity indicated by the manufacturer will contribute to energy and water savings.
Page 17
Upper Basket Top basket Height adjustment Dish rack Turn the Rail Stop Clips, at the ends of the rails, to the sides to open them (as shown in Upper basket racks have two positions: the image below), then pull out and remove open (a) and closed (b).
5.2. Alternative Basket Incorrect Loads Loads Lower Basket Top Basket Important Note for Test Laboratories For detailed information required for tests according to EN normatives and a softcopy of the manual, please send the model name and serial number to the following address: dishwasher@standardtest.info Incorrect Loads...
Page 20
• The program duration may change according to the amount of dishes, the water temperature, the ambient temperature and selected additional functions. • Values given for programmes other than the eco programme are indicative only • If your model has turbidity sensor, it has Auto program instead of Intensive program. •...
7. . THE CONTROL PANEL Selection knob to the 'Off' position. During a delay, the light corresponding to the remaining time is switched on. 7.1. Changing a Programme Follow the steps below to change a programme while in operation. Press the Start/Pause button. Rotate the Programme Selection Knob (3) to switch the machine on and select suitable programme for your dishes.
7.2. Cancelling a Programme NOTE: Do not open the door before the programme is complete. Follow the steps below to cancel a programme while in operation. NOTE: Leave the door slightly open at the end of a wash programme to speed up Press and hold the the drying process.
8. CLEANING AND To remove and clean the filter combination, turn it counter clockwise and remove it by MAINTENANCE lifting it upwards (1).Pull the coarse filter out of the micro filter (2).Then pull and remove Cleaning your dishwasher is important to the metal filter (3).Rinse the filter with lots of maintain the machine’s service life water until it is free of residue.
8.3 Drain Pump Large food residues or foreign objects which were not captured by the filters may block the waste water pump. The rinsing water will then be above the filter. Warning Risk of cuts! When cleaning the waste water pump, ensure that you do not injure yourself on pieces of broken glass or pointed implements.
9. TROUBLESHOOTING FAULT POSSIBLE CAUSE TROUBLESHOOTING Your Dishwasher is not plugged in. Plug your Dishwasher in. Switch your Dishwasher on by pressing the Your Dishwasher is not switched on. On/Off button. Fuse blown. Check your indoor fuses. The programme does not start.
Page 26
FAULT POSSIBLE CAUSE TROUBLESHOOTING Use the correct amount of detergent, as Not enough detergent used. instructed in the programme table. Rinse aid dosage and/or water Increase rinse aid and/or water softener softener setting set too low. level. Whitish stains remains on dishes.
Page 27
AUTOMATIC FAULT WARNINGS AND WHAT TO DO TROUBLE CODE POSSIBLE FAULT WHAT TO DO Start/ Wash Pause Make sure the water inlet tap is open and water is flowing. Insufficient water Separate the inlet hose from the tap and clean the filter of the hose. Contact for service if the error continues.
Page 28
The installation and repairing procedures should always carried out by the Authorised Service Agent in order to avoid possible risks. The manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorised persons. Repairs may be carried out by technicians only.
Need help?
Do you have a question about the LC2145E and is the answer not in the manual?
Questions and answers