Table of Contents
Advertisement
Quick Links
8000/8100/8200
T
M
o r q u e
a s T e r
s
l
Tandard
ifT
MH
q
s
G
uick
TarT
uide
PLEASE DO NOT RETURN THIS PRODUCT
TO THE STORE
Please Do Not Return This Product To The
Store. Please call 1-866-569-3799 (Press
Option 1) and follow the prompts to contact
the appropriate customer service agent. They
will be happy to handle any questions that
you may have.
©Copyright 2015
Wayne Dalton, a Division Of Overhead Door Corporation
P
®
l u s
T a b l e O f C o n t e n t s
QUICK START GUIDE IMPORTANT NOTICES!
This Quick Start Guide is only meant to be used as an aid and
/ or introduction to garage door installation, and does not replace the
complete Installation Instructions and Owner's manual available on the
web at www.Wayne Dalton.com. Wayne Dalton highly recommends
that you read and fully understand the Installation Instructions and
Owner's Manual before you attempt this installation.
To avoid possible injury, read the enclosed instructions carefully before
installing and operating the garage door. Pay close attention to all
warnings and notes. After installation is complete, fasten this manual
near garage door for easy reference.
DEFINITION OF DOOR HEIGHTS:
1. Door Heights less than or equal to 8'0" (< = 8'0") are considered
Standard Lift Applications.
The complete Installation Instructions and Owner's Manual are available at no
charge from:
Wayne Dalton, a Division Of Overhead Door Corporation,
P.O. Box 67, Mt. Hope, OH., 44660, Or Online At www.Wayne-Dalton.com
Part Number
341233
2
2
2
2
3
4
11
11
11
11
11
12
REV6_06/04/2015
Advertisement
Table of Contents
Related Manuals for Wayne-Dalton TorqueMaster Plus 8000
Summary of Contents for Wayne-Dalton TorqueMaster Plus 8000
-
Page 1: Table Of Contents
Standard Lift Applications. The complete Installation Instructions and Owner’s Manual are available at no charge from: Wayne Dalton, a Division Of Overhead Door Corporation, P.O. Box 67, Mt. Hope, OH., 44660, Or Online At www.Wayne-Dalton.com Part Number 341233 REV6_06/04/2015 ©Copyright 2015... -
Page 2: Pre-Installation
Wayne Dalton, A Division Of Overhead Door Corporation, P.O. Box 67, Mt. Hope, READ THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING INSTALLATION. IF IN QUES- OH., 44660, or at www.Wayne-Dalton.com. TION ABOUT ANY OF THE PROCEDURES, DO NOT PERFORM THE WORK. INSTEAD, HAVE A TRAINED DOOR SYSTEMS TECHNICIAN DO THE INSTALLATION OR REPAIRS. -
Page 3: Parts Breakdown
PARTS BREAKDOWN NOTE: The illustrations shown on this page are general representations of the door parts. Each specific door models may have unique variations. Top of vertical Top of vertical track track B1. (Fully Adjustable 3rd hole Feature) B2. (Quick hole set Install Feature) -
Page 4: Installation
flange is toward the back (flat) leg of the track. Repeat for other side. INSTALLATION JAMB BRACKET SCHEDULE DOOR TRACK 1ST SET 2ND SET 3RD SET HEIGHT LENGTH Before installing your door, be certain that you have read and followed all of the instruc- 6’0”... - Page 5 NOTE: The #4 graduated end hinges serves as end hinges on the Intermediate II section WARNING WARNING (used only on the fourth section of a five section high door). Starting on the left hand side of the bottom section, align the lower hinge leaf of the #1 FAILURE TO ENSURE TIGHT FIT OF CABLE LOOP OVER MILFORD PIN graduated end hinge over the holes, located at the top of the end caps.
- Page 6 OF THE BUILDING’S FLOOR, THE VERTICAL TRACKS AND THE DOOR BOTTOM SECTION Flag angle ASSEMBLY SHOULD BE INSTALLED SUCH THAT WHEN THE FLOOR IS CONSTRUCTED, NO DOOR OR TRACK PARTS ARE TRAPPED IN THE FLOOR CONSTRUCTION. 3/8”-16 IMPORTANT: THE TOPS OF THE VERTICAL TRACKS MUST BE LEVEL FROM SIDE TO SIDE. Hex nut IF THE BOTTOM SECTION WAS SHIMMED TO LEVEL IT, THE VERTICAL TRACK ON THE Flag angle...
- Page 7 sembly towards the center of the TorqueMaster ® spring tube, from the right side, as shown. Counterbalance lift cable Winding shaft Cable drum 1-1/2 wraps Cam peak Center bracket straight Grooves TorqueMaster ® spring tube Winding shaft Center bushing 5” Cam peak TorqueMaster spring...
- Page 8 Securing Door For Winding Spring(s) Grooves Tools Required: Vice Clamps, Step ladder, Safety glasses, Leather gloves Winding shaft Splines With the door in the fully closed position, place vice clamps onto both vertical tracks just above the third track roller. This is to prevent the garage door from rising while winding Disconnect cable spring(s).
- Page 9 Winding Spring(s) End bracket Tools Required: Ratchet wrench, 5/8” Socket, 3” Socket extension, Pliers / Wire cutters, Flat tip screwdriver, Step ladder, Tape measure, Safety glasses, Leather Marks gloves Pawl knob in lower position WARNING WARNING Ratchet wrench 5/8” Socket WINDING TORSION SPRING(S) IS AN EXTREMELY DANGEROUS PROCE- Winding DURE AND SHOULD BE PERFORMED ONLY BY A TRAINED DOOR SYSTEM...
- Page 10 Perforated Angle Gauge Weight Limitations: 1-1/4” x 1-1/4” x 13 Gauge Door Weight Less Than 305 lbs. 1-1/4” x 1-1/4” x 15 Gauge Door Weight Less Than 220 lbs. Sound framing 1-1/4” x 1-1/4” x 16 Gauge Door Weight Less Than 175 lbs. members NOTE: If an opener is installed, position horizontal tracks one hole above level when securing it to the rear back hangs.
-
Page 11: Maintenance
A Division Of Overhead Door Corporation, P.O. Box 67, Mt. Hope, OH., 44660, or at www. direct exposure to sunlight. Wayne-Dalton.com. For additional information on garage door/operator maintenance go to Cleaning the door will generally restore the appearance of the finish. To maintain an aestheti- www.dasma.com and reference TDS 151, 167 and 179. -
Page 12: Warranty
3. Lubrication: The door should open and close smoothly. Ensure the door track rollers are rotating freely when opening and closing the door. If track rollers do not rotate freely, clean the door tracks, removing dirt and any foreign substances. Clean and lubricate (use a non-silicon based lubricant) graduated end hinges, center hinge(s), steel track rollers, bearings and torsion spring(s) (torsion spring coil surfaces). - Page 14 Thank you for your purchase. PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE Please Do Not Return This Product To The Store. Please call 1-866-569-3799 (Press Option 1) and follow the prompts to contact the appropriate customer service agent. They will be happy to handle any questions that you may have.