Table of Contents
Advertisement
Quick Links
Model 44, Double
Flush
E
x t E n s i o n
r
EsidEntial
s
l
tandard
ift
Q
s
G
uick
tart
uidE
PLEASE DO NOT RETURN THIS PRODUCT
TO THE STORE
If you need assistance, please call 1-866-
569-3799 (press Option 1) and follow the
prompts to contact a customer service
representative. They will be happy to handle
any questions that you may have.
©Copyright 2020
Wayne Dalton, a division of Overhead Door Corporation
T a b l e O f C o n t e n t s
QUICK START GUIDE IMPORTANT NOTICES!
This Quick Start Guide is only meant to be used as an aid and
/ or introduction to garage door installation, and does not replace the
complete Installation Instructions and Owner's manual available on the
web at www.Wayne-Dalton.com. Wayne Dalton highly recommends
that you read and fully understand the Installation Instructions and
Owner's Manual before you attempt this installation.
To avoid possible injury, read and fully understand the enclosed
instructions carefully before installing and operating the garage door. Pay
close attention to all warnings and notes. After installation is complete,
fasten this manual near garage door for easy reference.
The complete Installation Instructions and Owner's Manual are available at no
charge from:
- Your local Wayne Dalton Sales Center, or
- Online at www.Wayne-Dalton.com, or
- By mailing to: Wayne Dalton, a division of Overhead Door Corporation, P.O. Box
67, Mt. Hope, OH., 44660
Part Number
347608
2
2
2
3
4
7
10
10
10
10
10
11
REV10_08/10/2020
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Wayne-Dalton EXTENSION 44
Summary of Contents for Wayne-Dalton EXTENSION 44
-
Page 1: Table Of Contents
If you need assistance, please call 1-866- complete Installation Instructions and Owner’s manual available on the web at www.Wayne-Dalton.com. Wayne Dalton highly recommends 569-3799 (press Option 1) and follow the that you read and fully understand the Installation Instructions and prompts to contact a customer service Owner’s Manual before you attempt this installation. -
Page 2: Pre-Installation
Existing Door & Prepar- ensure door operates freely. ing the Opening. These are available for download at www.Wayne-Dalton.com or at your 15. Test electric opener’s safety features monthly, following opener manufacturer’s instruc- local Wayne Dalton Sales Center. -
Page 3: Breakdown Of Parts
BREAKDOWN OF PARTS NOTE: The illustrations shown on this page are general representations of the door parts. Each specific door models may have unique variations. J6. J5. J10. J11. NOTE: For Item (K2), The Rear Center Back Hang Assemblies are to used for all doors over 11’0” door height and over 14’0”... -
Page 4: Door Installation Instructions
NOTE: Refer to Package Contents / Breakdown of Parts, to determine which bottom corner DOOR INSTALLATION brackets you have. Depending on which bottom corner brackets you have, slip the loop at the ends of the coun- INSTRUCTIONS terbalance lift cable over the milford pin of the bottom corner bracket or secure the cable loop to the clevis pin and bottom corner bracket using a flat washer and a cotter pin. - Page 5 FOR CENTER HINGES: Attach the upper slot of the graduated end hinge to the bottom (7) 1/4” - 20 x 2-1/2” Bottom Left hand bottom section using (1) 1/4” - 20 x 2-1/2” carriage bolt and (1) 1/4” - 20 flange hex nut. Next Carriage bolts section corner bracket...
- Page 6 TRACK ROLLER (IF INCLUDED) GOES INTO TUBE FURTHEST AWAY FROM SECTION. 4 Section High Strutting Schedule If applicable, repeat the same process for the other Intermediate sections, except for the top Intermediate II (1) Long Top Of Section section. Intermediate I (1) Long Attaching Top Fixtures And Strut To Top Sec- tion...
-
Page 7: Counterbalance Installation Instructions
assemblies / bottom slot in the angle mount to jamb, maintain 1/2” to 3/4” spacing, between 1/4” - 20 flange hex nuts. the bottom section and vertical track. IF YOU HAVE ANGLE MOUNT: To install horizontal track, place the curved end over the top track roller of the top section. - Page 8 12” Radius horizontal track with 3” front cable lift sheave hole location 90° 3/8”-16 15” Radius horizontal track Hex nut with 3” or 4” front cable lift sheave hole location Front cable lift sheave 12” Radius horizontal track with 4” front cable lift Perforated sheave hole location angle...
- Page 9 knot around the “horizontal angle” using a 3 hole clip, as shown. Insert one end of the small “S” hook into the “horizontal angle” with the 3 hole clip and the other end into the second slot 5/16” x 1-5/8” Lag bolt of the horizontal angle, as shown.
-
Page 10: Maintenance
Wayne Dalton 2501 S. State Hwy 121 Bus., Suite 200 Lewisville, TX 75067 For service, call (800) 827-3667 www.Wayne-Dalton.com SAFETY INSTRUCTIONS 1. Operate door ONLY when it is properly adjusted and free of obstructions. Residential warning label, The warning label will 2. -
Page 11: Warranty
WARRANTY available at no charge from Wayne Dalton, a division of Overhead Door Corporation, P.O. Box 67, Mt. Hope, OH., 44660, or at www.Wayne-Dalton.com. For additional information on garage door/operator maintenance go to www.dasma.com and reference TDS 151, 167 and 179. - Page 12 EXPRESS OR IMPLIED, WILL APPLY AFTER THE LIMITED WARRANTY PERIOD HAS EXPIRED. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. IN NO EVENT SHALL SELLER BE RESPONSIBLE FOR, OR LIABLE TO ANYONE FOR, SPECIAL, INDIRECT, COLLATERAL, PUNITIVE, INCIDENTAL OR CONSEQUENTIAL DAMAGES, even if Seller has been advised of the possibility of such damages.
- Page 14 Thank you for your purchase. PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE If you need assistance, please call 1-866-569-3799 (press Option 1) and follow the prompts to contact a customer service representative. They will be happy to handle any questions that you may have.
Need help?
Do you have a question about the EXTENSION 44 and is the answer not in the manual?
Questions and answers