Table of Contents
Advertisement
Available languages
Available languages
EN
OPTIONS AND SETTINGS
With each cycle additional options can be used. A full list of available options working with specific cycles can be found in the Cycles Table on
the previous page. All active options are shown on the display.
To set an option press „OK" button.
option list. Press „OK" to select the option, in the setting menu the LED above „OK" button is lit.
If the option is not available, it will be still visible in its position but with „
3D ZONE WASH
3D ZONE WASH
Option works with one rack at once. In particular, we recommend to
use it with Mixed and Intensive cycles - thanks to the additional 3D
water jets placed on the bottom o the cavity, ZONE WASH 3D option
allows to save energy or to increase the washing performance of the
dishwasher:
• 3D ZONE WASH + MIXED CYCLE: it allows to reduce energy
consumption up to 40%.
• 3D ZONE WASH + INTENSIVE CYCLE: it increases the washing
performances up to 40%. Ideal for very soiled mixed loads, e.g. pans
and saucepans, dishes with heavy encrustation or difficult-to-clean
crockery (grater, vegetable mill, dirty cutlery).
How to activate the option:
1. Select a compatible cycle.
2. Press
button to activate/deactive the option: a basket icon will
blink for a few seconds.
3D WASH
ACTIVATED
3. It is possible to change the selected rack pressing the ZONE WASH
button.
4. Remember to load the crockery in the selected rack only.
ZONE WASH
If there are not many dishes to be washed it can be loaded in one rack
only. Using this option you can select which rack you want to wash.
Select a compatible cycle (see "Cycles table"), and then press the ZONE
WASH
button: the symbol of the chosen rack will appear on the
display.
By default the ZONE WASH is not active and all racks icons are lit.
Selected only lower rack
Selected only upper rack
Selected only cutlery rack
Remember to load the upper or lower rack only, and to reduce the
amount of detergent accordingly. If upper rack is removed, please
apply detergent directly to tub instead of detergent dispenser.
TABLET (All-in-one)
This setting allows you to optimise the performance of the cycle
according to the type of detergent used. Enable it if you use combined
detergents in tablet form (rinse aid, salt and detergent in 1 dose).
TABLET
OFF
TABLET
ON
TABLET
ON
10
message is shown for a few seconds. Then use „<" or „>" button to navigate through the
SET OPTIONS
3D WASH
DEACTIVATED
To set the Tablet, enter in the setting
menu by pressing „OK" button and
navigate with „< , >" until „TABLET" is
shown, then press „OK" button.
"
START DELAY
The start of the cycle may be delayed for a selected period of time.
To set a delay, enter in the setting menu by pressing „OK" button and na-
vigate with „< , >" until „START DELAY" is shown, then press „OK" button.
With each press of the button ">" or "<", the delay start increases by:
• every 0:30 if selection below 4 hours,
• every 1:00 if selection is below 12 hours,
• every 2 hours if selection is above 12 hours.
START DELAY
OFF
<STARTS IN h>
OFF
<STARTS IN h>
4:00
<STARTS IN h>
4:00
To remove the delay, press „<" or „>" button until „OFF" is displayed.
TURBO
This option can be used to reduce the duration of the main cycles
while maintaining washing and drying performance levels.
TURBO
OFF
TURBO
ON
TURBO
ON
EXTRA DRY
This option allows to improve the drying of the dishes using higher
temperature during the final rinse and an extended drying phase.
The EXTRA DRY option results in the lengthening of the wash cycle.
EXTRA DRY
OFF
EXTRA DRY
ON
EXTRA DRY
ON
KEYLOCK
KEYLOCK ACTIVATED
PRESS „OK" FOR 3 SEC.
KEEP PRESSED...
KEYLOCK DEACTIVATED
Once set, to deactivate it keep pressing „OK" button for a few seconds.
TUB LIGHT
When the feature is active the LEDs in the tub are automatically swit-
ched on/off as soon as the user open/close the door respectively.
If the door remains opened for more than 10 min, the LEDs in the
tub switch off (to turn them on again, the door has to be closed and
opened again).This feature is active by default, but it is possible to
deactivate it in the "SETTINGS MENU".
Default value is OFF.
If delay is selected, the
is lit.
Once „OK" button is pressed the
delay is confirmed and the machine
comes back to the cycle selection
screen with delay value visible.
Press „START/PAUSE"
button to
start the delay.
To set the Turbo, enter in the setting
menu by pressing „OK" button and
navigate with „< , >" until „TURBO" is
shown, then press „OK" button.
With each press of the button „>" or
„<" option will be ON or OFF.
Confirm by pressing „OK" button.
To set the Extra Dry, enter in the
setting menu by pressing „OK" button
and navigate with „< , >" until
„EXTRA DRY" is shown, then press
„OK" button.
With each press of the button „>" or
„<" option will be ON or OFF.
Confirm by pressing „OK" button.
The KEYLOCK function blocks the
control panel except the „ON/OFF"
button.
To activate the Keylock, enter in the
setting menu by pressing „OK" button
and navigate with „< , >" until
„KEYLOCK" is shown, then press OK.
Advertisement
Table of Contents
