Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Weber CFR 90
Summary of Contents for Weber CFR 90
- Page 1 Operating and Maintenance Manual CFR 90 0101001 CFR 90...
- Page 2 CFR 90...
-
Page 3: Table Of Contents
Table of contents Introduction Safety guidelines Graphic presentation Device description Technical data Activities prior to starting work Starting Compacting Shutting down Maintenance overview Maintenance work Operating fluids and fill levels Troubleshooting Storage Contact addresses CFR 90... -
Page 4: Introduction
This operating and maintenance manual must always be available at the implementation site of the soil compactor. If necessary, you can obtain additional information from your authorized WEBER MT dealer, or you can obtain information from one of the contact addresses on the last page. -
Page 5: Safety Guidelines
The soil compactor should only be used if it is in a technically faultless condition, as intended, in a safety-conscious and hazard-conscious manner, and in compliance with the instructions in the operating manual. Malfunctions that impair safety must be eliminated without delay. The CFR 90 soil compactor is designed exclusively for compacting – sand, – gravel, –... - Page 6 Exercise particular caution when operating the engine in the vicinity of people and livestock. Maintenance and repair work Only use original Weber MT spare parts to ensure reliable and safe operation for maintenance or repair work. Hydraulic hose lines must be checked at regular intervals in accordance with standard engineering practice, or they must be replaced at appropriate intervals, even if no signs of safety-relevant defects are present.
- Page 7 Important information for operating and maintenance personnel is marked by pictograms. Warning against irritants or materials hazardous to health Warning against a hazardous place Warning against a suspended load Wear ear protection General regulation Environmental protection Hard hat Safety shoes Protective gloves CFR 90...
-
Page 8: Graphic Presentation
Graphic presentation Overall view CFR 90 1 Engine 2 Guide bracket 3 Engine bracket 4 Undercarriage (accessory) (no image) 5 Base plate 6 Hearing protection (sticker) 7 Exciter 8 Throttle lever CFR 90... -
Page 9: Device Description
Device description The CFR 90 compactor is used for road-building and landscaping compaction tasks. Drive The unit is powered by an air-cooled Honda gasoline engine. Force is transferred to the exciter mechanically via a V-belt. Operation Start the Honda gasoline engine with the attached reversing starter. After starting, vibration is switched on via the centrifugal clutch attached to the engine. -
Page 10: Technical Data
Technical data CFR 90 Weight Operating weight CECE in kg Dimensions Overall length (in mm) Overall width (in mm) Height Base plate length (in mm) Pressure surface (in mm) 430 x 350 Drive Engine manufacturer Honda Type GX 160 Performance at operating speed in accordance... - Page 11 1 Description 2 TYPE .......................... 3 Serial number 4 Year of construction .......................... 5 Mass 6 Rated power kW .......................... CFR 90...
-
Page 12: Activities Prior To Starting Work
Insert axle bolt (2) of the wheel set into the retainer bush (3) of the undercarriage. Insert axle bolt (3) into the retainer bush of the undercarriage. Use the protective frame to guide the machine (4). Risk of injury if the machine tips over. CFR 90... - Page 13 For work at the fuel system, have a suitable fire-extin- guishing agent at the ready. Fire, naked light, and smoking is forbidden! CFR 90...
-
Page 14: Starting
Allow the handle (5) to glide back into the initial position, and then forcefully and completely pull it through with both hands. After the engine has warmed up, slide the choke lever to the right (open). CFR 90... -
Page 15: Compacting
Turn the short-circuit button (5) to the “0” – OFF position. During breaks – even if they are short – the machine must be shut down. Parked devices that represent an obstacle must be safeguarded against through conspicuous measures. CFR 90... -
Page 16: Maintenance Overview
If lubricating oils and fuel come into contact with skin, they can cause skin cancer. Upon contact with the skin, clean affected skin with suitable cleaning agent without delay. If accessible during maintenance, check the condition and stability of all screws. CFR 90... -
Page 17: Maintenance Work
Clean / change air filter cartridge Unscrew the air filter cover (3). Remove the air filter insert (4) from the air filter enclosure. Clean air filter insert as specified by the engine manufacturer if there is damage or if it is extremely dirty. CFR 90... - Page 18 Wipe up / off oil slick and oil residue and dispose of fuel-soaked cleaning cloths in an environmentally re- sponsible manner. Checking the V-belt Remove the V-belt guard (2). Check the V-belt (3) for cracks, damaged flanks, and wear. If there is excessive wear, replace the V-belt. CFR 90...
-
Page 19: Operating Fluids And Fill Levels
Operating fluids and fill levels Assembly Operating material Quantity CFR 90 Quality Engine Engine oil SAE 10 W 40 0.6 L (– 10 ~ + 50 °C) API – CD CE or SHPD or CCMC – D2 – D3 – PD1... -
Page 20: Storage
All bare parts / gas lever / accelerator – Oil / grease control cables / fastening bolts If the machine is to be stored for longer than six months, then contact the Weber service organi- zation to discuss additional measures. CFR 90... - Page 21 Notiz / note: CFR 90...
- Page 22 Notiz / note: CFR 90...
-
Page 23: Contact Addresses
Notiz / note: CFR 90... - Page 24 Weber Maschinentechnik GmbH Im Boden 5-8, 10 · 57334 Bad Laasphe · Germany Phone +49 2754 398 0 · Fax +49 2754 398 101 info@webermt.de · www.webermt.de 085100401-104 / CFR 90_2020-03 Original instructions CFR 90...