Advertisement
solid and guarantee a stable fixture.
• Make sure that the sensor is protected against ac-
cidental impact.
3 - PRODUCT INSTALLATION
For installation, fix the various parts of the product in
numerical order as shown in the Quick reference guide
(Step 1 - fig. B). When installing WS and WSR sen-
sors, connect the power supply (Quick reference guide
- Step 1 - fig. C). Then adjust the sensor body as
shown in the Quick reference guide and make sure that
the wind sensor blades are horizontal (Quick reference
guide - Step 1 - fig. D).
3.1 - Activation of WSC sensor
The WSC sensor is shipped in standby mode. To acti-
vate the sensor: press the B Button once, the LED will
flash orange twice, turn off, then light up green for 2
seconds (Quick reference guide - Step 1 - fig. E).
3.2 - Activation of WS/WSR sensor
To activate the sensor: turn the power supply on, the
LED will flash orange twice, turn off, then light up green
for 2 seconds (Quick reference guide - Step 1 - fig. E).
3.3 - Re-activation of WS/WSC/WSR sensor
During the subsequent startups, the LED flashing color
is based on to the selected protocol:
• flashing orange - orange - red - monodirectional,
• flashing orange - orange - green - bidirectional.
4 - MEMORIZING THE SENSOR IN THE MO-
TOR RECEIVER
As for any other transmitter, the climatic sensor's radio
code must be memorized in the receiver of the motor
it controls, so that the sensor can send wireless com-
mands. To memorise the sensor follow the "Mode I"
procedure described in the manual of the tubular mo-
tor or associated receiver. Alternatively the following
memorization procedure can be used.
Caution! – Memorize only one type of the transmitter:
monodirectional or bidirectional. Do not mix the types.
4.1 - Memorising climatic sensor using an already
memorised transmitter in Monodirectional mode
(Quick reference guide - Step 2a)
• Before performing the procedure, move the awning
to the middle position.
• To escape the procedure at any point, press the B
button.
1. Press and hold the B Button for 2 to 4 seconds,
release when the LED changes to red.
2. Press and hold the
Button for at least 10 sec-
onds (the LED should be flashing red).
3. Press the button of a previously memorized trans-
mitter 3 times (slowly).
4. Press and hold the
Button for at least 2 seconds
for the sensor to be memorized and check that the
motor performs 3 movements (= memorization suc-
cessful).
5. Press the B Button once to end the procedure.
4.2 - Memorising climatic sensor using an already
memorised transmitter in Bidirectional mode
(Quick reference guide - Step 2b)
• Before performing the procedure, move the awning
to the middle position.
• To escape the procedure at any point, press the B
button.
1. Press and hold the B Button for 6 to 8 seconds,
release when the LED changes to orange.
2. Press the PRG/P button of a previously memorized
transmitter once (confirmed with 2 motor move-
ments).
3. Press and hold the
Button for at least 4 seconds
(confirmed with 2 motor movements).
4. Press the PRG/P button of a previously memorized
transmitter once (confirmed with 2 motor move-
ments).
5. Press the
Button for the sensor to be memorized
and check that the motor performs 3 movements (=
memorization successful).
6. Press the B Button once to end the procedure.
4.3 - Memorisation through the "Enable Code"
1. Press and hold the B Button for 8 to 10 seconds,
release when the LED changes to green.
2. The device should blink green once, then 3 times
fast, showing the current state of each group:
• green - free space,
• red - space used,
• orange - not bound with any devices.
3. Press the
Button:
• 1x to select 1st group (LED blinks orange 1x),
• 2x to select 2nd group (LED blinks orange 2x),
• 3x to select 3rd group (LED blinks orange 3x).
4. Turn on the remote, select group, then press the
Button on the climatic once. The LED should be
flashing orange.
5. The device should blink green once, then 3 times
fast, showing the current space of each group:
• green - free space,
• red - space used,
• orange - not bound with any devices.
6. Press and hold the B Button for 1 to 3 seconds to
bind with devices from the copy group.
7. Press the B Button once to end the procedure.
4.4 - Confirming memorisation (Quick reference
guide - Step 3)
1. Press the s button of a previously memorized
transmitter to start UP movement.
2. Press the B button and check that the motor stops.
• B button stops the motor only if not in the procedure
or programming menu.
5 - TESTING THE SENSORS
Once the sensors have been memorized, they must be
tested as follows.
5.1 - Testing the sun sensor (Quick reference
guide - Step 4)
• Before performing the procedure, move the awning
to a middle position.
• To escape the procedure at any point, press the B
English – 17
Advertisement
