3M AccuGlide II STD Instructions And Parts List

2 inch upper and lower taping heads

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

Instructions and Parts List

AccuGlide II

STD 2 Inch

Upper and Lower

Taping Heads

Type 39600

Serial No.

_____________________________________

For reference, record taping head(s) serial number(s) here.

3M Packaging Systems Division

3M Center, Building 220-8W-01

St. Paul, MN 55144-1000

Important Safety

Information

Read "Important Safeguards",

page 2 and also operating

"Warnings", page 7

BEFORE INSTALLING OR

OPERATING THIS

EQUIPMENT.

Spare Parts

It is recommended you

immediately order the

spare parts listed on

page 17. These parts are

expected to wear through

normal use, and should

be kept on hand to minimize

production delays.

AccuGlide

™

is a Trademark of

3M, St. Paul, MN 55144-1000

Litho in U.S.A

Table of Contents

Summary of Contents for 3M AccuGlide II STD

Page 1 Serial No. _____________________________________ For reference, record taping head(s) serial number(s) here. AccuGlide ™ is a Trademark of 3M Packaging Systems Division 3M, St. Paul, MN 55144-1000 Litho in U.S.A 3M Center, Building 220-8W-01 St. Paul, MN 55144-1000 © 3M 1998 44-0009-1893-6(D28.0)
Page 2 Minimum billing on parts orders will be $25.00. Replacement part prices available on request. $10.00 restocking charge per invoice on returned parts. Note : Outside the U.S., contact the local 3M subsidiary for parts ordering information. "3M-Matic", "AccuGlide" and “Scotch” are trademarks of 3M Packaging Systems Division 3M, St.
Page 3 Replacement Parts And Service Information To Our Customers: This is the 3M-Matic™/AccuGlide™/Scotch™ brand equipment you ordered. It has been set up and tested in the factory with "Scotch" brand tapes. If any problems occur when operating this equipment, and you desire a service call, or phone consultation, call, write or Fax the appropriate number listed below.
Page 4: Table Of Contents
Instruction Manual ™ AccuGlide II STD 2 Inch Upper and Lower Taping Heads Type 39600 Table of Contents Page Equipment Warranty and Limited Remedy ..................... Taping Head Contents ..........................Intended Use ............................Important Safeguards ..........................Specifications ............................3 - 4 Dimensional Drawing ........................
Page 5: Equipment Warranty And Limited Remedy
3M is notified of the problem no later than five (5) calendar days after the warranty period. If 3M is unable to repair or replace the part within a reasonable time, then 3M, at its option, will replace the equipment or refund the purchase price.
Page 6: Intended Use
Upper and Lower Taping Heads is to apply a "C" suitable for mounting in box conveying systems clip of Scotch™ brand pressure-sensitive film box other than 3M-Matic™ case sealers. This includes sealing tape to the top and/or bottom center seam of replacement of other types of taping, gluing or regular slotted containers.
Page 7: Important Safeguards
Important Safeguards This safety alert symbol identifies important safety messages in this manual. READ AND UNDERSTAND THEM BEFORE INSTALLING OR OPERATING THIS EQUIPMENT. Important – In the event the following safety labels are damaged or destroyed, they must be replaced to ensure operator safety. See Parts Drawing/Lists, pages 18-35 for label part numbers.
Page 8: Specifications
Case Sealer Width – 115 mm [4-1/2 inches] When upper and lower taping heads are used on “3M-Matic” case sealers, refer to the respective instruction manual specifications for box weight and size capacities. Operating Rate: Conveyor speeds up to 0.40 m/s [80 FPM] maximum.
Page 9: Dimensional Drawing
Specifications (Continued) Figure 2-1 – Dimensional Drawing...
Page 10: Installation
3M Representative. Note – AccuGlide™ II STD taping Heads are supplied with a buffing arm guard. This guard...
Page 11: Operation
Operation Figure 3-1 – Taping Head Components/Threading Diagram, Upper Head (Left Side View) Figure 3-2 – Taping Head Components/Threading Diagram – Lower Head (Left Side View)
Page 12: Tape Loading - Upper Taping Head
Operation (Continued) WARNINGS 1. Turn air and electrical supplies off and disconnect before servicing taping heads. 2. Never attempt to work on the taping heads or load tape when the box drive system is running. 3. The taping heads are equipped with an extremely sharp cut-off knife. Before working with the taping heads or attempting to load/thread tape, refer to Figures 3-1 and 3-2 and identify the knife location.
Page 13 Operation (Continued) Figure 3-4 Place tape roll on tape drum to dispense tape with adhesive side forward. Seat tape roll fully against back flange of drum. Adhere tape lead end to threading needle as shown. Figure 3-4 – Tape Loading/Threading Figure 3-5 WARNING –...
Page 14: Maintenance
Maintenance WARNINGS 1. Turn air and electrical supplies off and disconnect before beginning maintenance. 2. Use care when working near tape cut-off knife as knife is extremely sharp. 3. Failure to comply with these warnings could result in severe personal injury or equipment damage.
Page 15: Lubrication
Maintenance (Continued) WARNINGS 1. Turn air and electrical supplies off and disconnect before beginning maintenance. 2. Use care when working near tape cut-off knife as knife is extremely sharp. 3. Failure to comply with these warnings could result in severe personal injury or equipment damage.
Page 16: Adjustments
Adjustments WARNING – Turn air and electrical supplies off and disconnect before beginning adjustments. Failure to comply with this warning could result in severe personal injury and/or equipment damage. Tape Web Alignment – Figure 5-1 The STD tape drum assembly is pre-set to accommodate 48 mm [2 inch] wide tape.
Page 17: Applying Mechanism Spring
Adjustments (Continued) WARNING – Turn air and electrical supplies off and disconnect before beginning adjustments. Failure to comply with this warning could result in severe personal injury and/or equipment damage. Applying Mechanism Spring To obtain access to the spring, remove the taping head cover (four mounting screws).
Page 18: Tape Leg Length
Adjustments (Continued) WARNING – Turn air and electrical supplies off and disconnect before beginning adjustments. Failure to comply with this warning could result in severe personal injury and/or equipment damage. Tape Leg Length WARNING – Use care when working near tape cut-off knife as knife is extremely sharp.
Page 19 THIS PAGE IS BLANK...
Page 20: Troubleshooting
Troubleshooting Troubleshooting Guide Problem Cause Correction The tape is threaded incorrectly The tape must go around the wrap The tape leg on the front of the roller before going around the case is too long one-way tension roller The tape tension is too low Adjust the one-way tension roller The knurled roller drags Check for adhesive build-up...
Page 21 Troubleshooting (Continued) Troubleshooting Guide Cause Correction Problem There is excess tension on the Adjust the one-way tension roller Tape is tabbing on the trailing leg tape drum assembly and/or the and/or the tape drum assembly on the back of the box one-way tension roller assembly Rollers in the tape path do not Clean adhesive deposits from the...
Page 22: Spare Parts/Service Information
Spare Parts/Service Information Recommended Spare Parts A set of spare parts that will periodically require replacement due to normal wear is supplied with the taping heads. The set includes the following which should be reordered when used to keep the taping heads in production: AccuGlide™...
Page 23: Replacement Parts Illustrations And Parts List
Refer to the first page of this instruction manual "Replacement Parts and Service Information" for replacement parts ordering information. IMPORTANT – Not all the parts listed are normally stocked items. Some parts or assemblies shown are available only on a special order basis. Contact 3M/Tape Dispenser Parts to confirm item availability.
Page 24 ™ Taping Head Assemblies – AccuGlide II STD 2 Inch...
Page 25 Figure 2879 – Upper Head...
Page 26 Figure 2879 – Upper Head Ref. No. 3M Part No. Description 2879-1 78-8070-1386-3 Frame – Tape Mount Upper Assembly 2879-2 78-8070-1387-1 Frame – Front Upper Assembly 2879-3 78-8068-4143-9 Guide – #1 2879-4 78-8068-4144-7 Guide – #2 2879-5 83-0002-7336-3 Screw – Hex Hd, M4 x 14...
Page 27 Figure 2880 – Upper and Lower Heads...
Page 28 Figure 2880 – Upper and Lower Heads Ref. No. 3M Part No. Description 2880-1 78-8070-1206-3 Applying Arm #1 2880-2 78-8070-1207-1 Applying Arm #2 2880-3 78-8070-1221-2 Plate – Tape 2880-4 78-8070-1309-5 Shaft Roller 2880-5 78-8070-1367-3 Roller – Knurled Assembly 2880-6 78-8070-1266-7 Roller –...
Page 29 Figure 2881 – Upper Head...
Page 30 Figure 2881 – Upper Head Ref. No. 3M Part No. Description 2881-1 78-8070-1392-1 Buffing Arm – Sub Assembly 2881-2 78-8070-1391-3 Buffing Arm – Sub Assembly 2881-3 78-8052-6575-4 Shaft – Roller 2881-4 78-8052-6586-1 Bushing – Buffing Roller 2881-5 78-8057-6178-6 Roller – Buffing...
Page 31 Figure 2882 – Upper and Lower Heads...
Page 32 Figure 2882 Upper and Lower Heads – Ref. No. 3M Part No. Description 2882-1 78-8070-1388-9 Link – Arm Bushing Assembly 2882-2 78-8070-1389-7 Link – Arm Bushing Assembly 2882-3 78-8070-1271-7 Shaft – Pivot 2882-4 78-8017-9082-1 Bearing – Special 30 mm 2882-5 78-8017-9106-8 Screw –...
Page 33 Figure 2883 – Upper and Lower Heads...
Page 34 Figure 2883 – Upper and Lower Heads Ref. No. 3M Part No. Description 2883-1 78-8070-1217-0 Frame – Cut-Off Weldment 2883-2 78-8017-9173-8 Knife – 65 mm/2.56 Inch 2883-3 26-1002-5817-2 Screw – Hex Hd, M5 x 8 2883-4 78-8070-1371-5 Knife Guard Assembly – W/English Language Label...
Page 35 Figure 2884 – Upper and Lower Heads...
Page 36 Figure 2884 – Upper and Lower Heads Ref. No. 3M Part No. Description 2884-1 78-8070-1395-4 Bracket – Bushing Assembly 2884-2 78-8076-4519-3 Shaft – Tape Drum, 50 mm 2884-3 78-8017-9169-6 Nut – M18 x 1 2884-4 78-8070-1569-4 Tape Drum Sub Assembly...
Page 37 Figure 2885 – Lower Head...
Page 38 Figure 2885 – Lower Head Ref. No. 3M Part No. Description 2885-1 78-8070-1369-9 Frame – Tape Mount Lower Assembly 2885-2 78-8070-1370-7 Frame – Front Lower Assembly 2885-3 78-8068-4144-7 Guide – #2 2885-4 78-8068-4143-9 Guide – #1 2885-5 83-0002-7336-3 Screw – Hex Hd, M4 x 14...
Page 39 Figure 2886 – Lower Head...
Page 40 Figure 2886 – Lower Head Ref. No. 3M Part No. Description 2886-1 78-8070-1391-3 Buffing Arm Sub Assembly 2886-2 78-8070-1392-1 Buffing Arm Sub Assembly 2886-3 78-8052-6575-4 Shaft – Roller 2886-4 78-8052-6586-1 Bushing – Buffing Roller 2886-5 78-8057-6178-6 Roller – Buffing 2886-7 78-8070-1220-4 Spacer –...

This manual is also suitable for:

39600

3M AccuGlide II STD Instructions And Parts List

Quick Links

Related Manuals for 3M AccuGlide II STD

Summary of Contents for 3M AccuGlide II STD

This manual is also suitable for:

Table of Contents