3M AccuGlide II 29600 Instructions And Parts List
  1. Manuals
  2. Brands
  3. 3M Manuals
  4. Packaging equipment
  5. AccuGlide II 29600
  6. Instructions and parts list
3M AccuGlide II 29600 Instructions And Parts List

3M AccuGlide II 29600 Instructions And Parts List

Std 1-1/2 inch lower taping head
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Instructions and
Parts List
AccuGlide II
STD 1-1/2 Inch
Lower Taping Head
Type 29600
Serial No.
_____________________________________
For reference, record taping head serial number here.
3M Packaging Systems Division
3M Center, Building 220-8W-01
St. Paul, MN 55144-1000
TM
Important Safety
Information
Read "Important Safeguards",
page 2 and also operating
"Warnings", page 7 BEFORE
INSTALLING OR
OPERATING THIS
EQUIPMENT
Spare Parts
It is recommended you
immediately order the
spare parts listed on
page 17. These parts are
expected to wear through
normal use, and should
be kept on hand to minimize
production
delays.
"AccuGlide" is a Trademark of 3M,
St. Paul, MN 55144-1000
Litho in U.S.A
© 3M 1998 44-0009-1924-9 (B28.0)

Advertisement

Table of Contents
loading

Related Manuals for 3M AccuGlide II 29600

Summary of Contents for 3M AccuGlide II 29600

  • Page 1 Serial No. _____________________________________ For reference, record taping head serial number here. 3M Packaging Systems Division "AccuGlide" is a Trademark of 3M, St. Paul, MN 55144-1000 3M Center, Building 220-8W-01 Litho in U.S.A St. Paul, MN 55144-1000 © 3M 1998 44-0009-1924-9 (B28.0)
  • Page 2 Minimum billing on parts orders will be $25.00. Replacement part prices available on request. $10.00 restocking charge per invoice on returned parts. Note : Outside the U.S., contact the local 3M subsidiary for parts ordering information. "3M-Matic", "AccuGlide" and “Scotch” are trademarks of 3M Packaging Systems Division 3M, St.
  • Page 3 Replacement Parts And Service Information To Our Customers: This is the 3M-Matic™/AccuGlide™/Scotch™ brand equipment you ordered. It has been set up and tested in the factory with "Scotch" brand tapes. If any problems occur when operating this equipment, and you desire a service call, or phone consultation, call, write or Fax the appropriate number listed below.

  • Page 4: Table Of Contents

    Instruction Manual AccuGlide™ II STD 1-1/2 Inch Lower Taping Head Type 29600 Table of Contents Page Equipment Warranty and Limited Remedy ..................... Taping Head Contents ..........................Description .............................. Important Safeguards ..........................Specifications ............................3 - 4 Dimensional Drawing ........................Installation ............................... Receiving and Handling .......................

  • Page 5: Equipment Warranty And Limited Remedy

    3M is notified of the problem no later than five (5) calendar days after the warranty period. If 3M is unable to repair or replace the part within a reasonable time, then 3M, at its option, will replace the equipment or refund the purchase price.

  • Page 6: Description

    Description The design of this taping head allows it to be The AccuGlide ™ STD 1-1/2 Inch Lower Taping mounted in the upper or lower taping locations. The Head, was designed to be used in the 800asb Case compact size and simplicity of the taping head also Sealer.

  • Page 7: Important Safeguards

    Important Safeguards This safety alert symbol identifies important safety messages in this manual. READ AND UNDERSTAND THEM BEFORE INSTALLING OR OPERATING THIS EQUIPMENT. Important – In the event the following safety labels are damaged or destroyed, they must be replaced to ensure operator safety. See Parts Drawing/Lists, pages 18-31 for label part numbers.

  • Page 8: Specifications

    Limited by case sealer Limited by case sealer When lower taping head is used on “3M-Matic” case sealers, refer to the respective instruction manual specifications for box weight and size capacities. Operating Rate: Conveyor speeds up to 0.40 m/s [80 FPM] maximum.

  • Page 9: Dimensional Drawing

    Specifications Figure 2-1 – Dimensional Drawing...

  • Page 10: Installation

    70 mm [2-3/4 inches], the taping file a damage claim immediately with the heads must be completely staggered so only transportation company and also notify your 3M one tape seal is being applied at one time. Representative. Note – AccuGlide™ II STD taping Heads are supplied with a buffing arm guard.

  • Page 11: Operation

    Operation Figure 3-1 – Taping Head Components/Threading Diagram – Upper Head (Left Side View) Figure 3-2 – Taping Head Components/Threading Diagram – Lower Head (Left Side View)

  • Page 12: Tape Loading - Lower Taping Head

    Operation (Continued) WARNINGS 1. Turn air and electrical supplies off and disconnect before servicing taping head. 2. Never attempt to work on the taping head or load tape when the box drive system is running. 3. The taping head uses an extremely sharp tape cut-off knife. Before working with the taping head or attempting to load/thread tape, refer to Figures 3-1 and 3-2 and identify the knife location.

  • Page 13: Buffing Roller Pressure Adjustment

    Operation (Continued) Figure 3-5 WARNING – Use care when working near cut-off knife as knife is extremely sharp. If care is not taken, severe personal injury could result. Manually turn tape roll to create slack tape while pulling threading needle through tape applying mechanism until needle is through and tape is in alignment with applying roller.

  • Page 14: Maintenance

    Maintenance WARNINGS 1. Turn air and electrical supplies off and disconnect before beginning maintenance. 2. Use care when working near tape cut-off knife as knife is extremely sharp. 3. Failure to comply with these warnings could result in severe personal injury or equipment damage.

  • Page 15: Lubrication

    Maintenance (Continued) WARNINGS 1. Turn air and electrical supplies off and disconnect before beginning maintenance. 2. Use care when working near tape cut-off knife as knife is extremely sharp. 3. Failure to comply with these warnings could result in severe personal injury or equipment damage.

  • Page 16: Adjustments

    Adjustments WARNING – Turn air and electrical supplies off and disconnect before beginning adjustments. Failure to comply with this warning could result in severe personal injury and/or equipment damage. Applying Mechanism/Buffing Extension Springs To obtain access to the spring, remove the taping head cover (four mounting screws).

  • Page 17: Tape Web Alignment

    Adjustments (Continued) WARNING – Turn air and electrical supplies off and disconnect before beginning adjustments. Failure to comply with this warning could result in severe personal injury and/or equipment damage. Tape Web Alignment – Figure 5-3 The STD tape drum assembly is pre-set to accommodate 36 mm [1.50 inch] wide tape.

  • Page 18: Tape Leg Length

    Adjustments (Continued) WARNING – Turn air and electrical supplies off and disconnect before beginning adjustments. Failure to comply with this warning could result in severe personal injury and/or equipment damage. Tape Leg Length WARNING – Use care when working near cut-off knife as knife is extremely sharp.

  • Page 19: One-Way Tension Roller

    Adjustments (Continued) WARNING – Turn air and electrical supplies off and disconnect before beginning adjustments. Failure to comply with this warning could result in severe personal injury and/or equipment damage. One-Way Tension Roller Figure 5-7 The one-way tension roller is factory set. When replacing this assembly, the roller must have 0.5 kg [1 lb.] minimum tangential force when turning.

  • Page 20: Troubleshooting

    Troubleshooting Cause Correction Problem The tape is threaded incorrectly The tape must go around the wrap The tape leg on the front of the roller before going around the case is too long one-way tension roller The tape tension is too low Adjust the one-way tension roller The knurled roller drags Check for adhesive build-up...
  • Page 21 Troubleshooting (Continued) Cause Correction Problem There is excess tension on the Adjust the one-way tension roller Tape is tabbing on the trailing leg tape drum assembly and/or the and/or the tape drum assembly on the back of the box one-way tension roller assembly Rollers in the tape path do not Clean adhesive deposits from the rotate freely...

  • Page 22: Spare Parts/Service Information

    Spare Parts/Service Information Recommended Spare Parts A set of spare parts that will periodically require replacement due to normal wear is supplied with the taping heads. The set includes the following which should be reordered when used to keep the taping heads in production: AccuGlide™...

  • Page 23: Replacement Parts Illustrations And Parts List

    Refer to the first page of this instruction manual “Replacement Parts and Service Information” for replacement parts ordering information. IMPORTANT – Not all the parts listed are normally stocked items. Some parts or assemblies shown are available only on a special order basis. Contact 3M/Tape Dispenser Parts to confirm item availability.
  • Page 24 ™ Taping Head Assemblies – AccuGlide STD 1-1/2 Inch...
  • Page 25 Figure 4792 – Lower Head...
  • Page 26 Figure 4792 – Lower Head Ref. No. 3M Part No. Description 4792-1 78-8070-1206-3 Arm – Applying, R/H 4792-2 78-8070-1207-1 Arm – Applying, L/H 4792-3 78-8094-6146-6 Plate 4792-4 78-8094-6147-4 Shaft – /10 4792-5 78-8094-6148-2 Roller – Knurled 4792-6 78-8094-6149-0 Roller 4792-7 78-8094-6150-8 Spacer –...
  • Page 27 Figure 4794 – Lower Head...
  • Page 28 Figure 4794 – Lower Head Ref. No. 3M Part No. Description 4794-1 78-8070-1388-9 Link – Arm Bushing Assembly 4794-2 78-8070-1389-7 Link – Arm Bushing Assembly 4794-3 78-8094-6158-1 Shaft - Pivot 4794-4 78-8094-6151-6 Washer 4794-5 78-8017-9082-1 Bearing – Special, 30 mm...
  • Page 29 Figure 4795 – Lower Head...
  • Page 30 Figure 4795 – Lower Head Ref. No. 3M Part No. Description 4795-1 78-8094-6159-9 Frame – Cut-Off Weldment 4795-2 78-8017-9173-8 Knife – 2.56 Inch (65 mm) 4795-3 26-1002-5817-2 Screw – Hex Hd, M5 x 8 4795-4 78-8113-6821-2 Guard – Blade, W/English Language Label...
  • Page 31 Figure 4797 – Lower Head...
  • Page 32 Figure 4797 – Lower Head Ref. No. 3M Part No. Description 4797-1 78-8070-1369-9 Frame – Tape Mount Lower Assembly 4797-2 78-8070-1370-7 Frame – Front Lower Assembly 4797-3 78-8068-4144-7 Guide – #2 4797-4 78-8068-4143-9 Guide – #1 4797-5 83-0002-7336-3 Screw – Hex Hd, M4 x 14...
  • Page 33 Figure 4798 – Lower Head...
  • Page 34 Figure 4798 – Lower Head Ref. No. 3M Part No. Description 4798-1 78-8070-1392-1 Buffing Arm Sub Assembly 4798-2 78-8070-1391-3 Buffing Arm Sub Assembly 4798-3 78-8094-6152-4 Shaft – /10 x 48 4798-4 78-8094-6154-0 Bushing – Buffing Roller 4798-5 78-8094-6155-7 Roller – Buffing...
  • Page 35 Figure 4799 – Lower Head...
  • Page 36 Figure 4799 – Lower Head Ref. No. 3M Part No. Description 4799-1 78-8070-1395-4 Bracket – Bushing Assembly 4799-2 26-1003-5829-5 Screw – Hex Hd, M6 x 12 4799-3 78-8100-1051-8 Spacer – Guard 4799-4 78-8060-8474-1 Tape Drum Assembly – 2 Inch Head...

Table of Contents