Included with each machine is an Instructions and Parts List manual. Technical Assistance / Replacement Parts and Additional Manuals: Call the 3M-Matic™ Help line at 1-800 328-1390. Provide the customer support coordinator with the model/machine name, machine type, and serial number that are located on the identifi cation plate (For example: Model HST 2"...
Instruction Manual ™ AccuGlide HST 2 Inch Upper and Lower Taping Heads Type 41000 Table of Contents Page Replacement Parts and Service Information .................... i - ii Table of Contents............................Equipment Warranty and Limited Remedy ....................Intended Use ............................Taping Head Contents / How to Use Manual.................... Important Safeguards ..........................
If any part is defective within this warranty period, your exclusive remedy and 3M’s and seller’s sole obligation shall be, at 3M’s option, to repair or replace the part. 3M must receive actual notice of any alleged defect within a reasonable time after it is discovered, but in no event shall 3M have any obligation under this warranty unless it receives such notice within fi...
Scotch pressure-sensitive fi lm box sealing other than 3M-Matic™ case sealers. This includes ® tape to the top and/or bottom center seam of regular replacement of other types of taping, gluing or slotted containers.
HST 2" / 3M Industrial Adhesives and Tapes Division 3M Center, Bldg. 220-5E-06 St. Paul, MN 55144-1000 (USA) / Edition February 2010 / Copyright 3M 2010 / All rights re- served. The manufacturer reserves the right to change the product at any time without notice.
Important Safeguards This safety alert symbol identifi es CAUTION important safety messages in this manual. READ AND UNDERSTAND • To reduce the risk associated with muscle THEM BEFORE INSTALLING OR strain: OPERATING THIS EQUIPMENT. − Use proper body mechanics when removing or installing taping heads that are Explanation of Signal Word Consequences moderately heavy or may be considered...
Page 13
Important - In the event the following safety labels are damaged or destroyed, they must be replaced to ensure operator safety. See "Replacement Parts Illustrations and Parts Lists" for label part numbers. 78-8137-3527-7 78-8070-1335-0 78-8137-3528-5 Lower Tape Threading Label (not shown) Figure 1-1 Replacement Labels/3M Part Numbers February 2010 HST 2" Taping Head - NA...
Case Sealer Width – 115mm [4-1/2 inches] When upper and lower taping heads are used on “3M-Matic” case sealers, refer to the respective instruction manual specifi cations for box weight and size capacities. Operating Rate: Conveyor speeds up to 0.76 m/s [150 FPM] maximum.
70mm [2-3/4 inches], the taping heads evident, fi le a damage claim immediately with the must be completely staggered so only one tape transportation company and also notify your 3M seal is being applied at one time. Representative.
Operation Tape Drum Main Spring Tape Supply Roll Buffi ng Arm Tape Adhesive Side Cover One-Way Tension Roller Midpoint Tension Wrap Roller Spring Knurled Roller Wrap Roller Tape Cut-Off Knife Threading Needle Orange Knife Guard Buffi ng Applying Roller Roller Figure 3-1 Taping Head Components/Threading Diagram - Upper Head (Left Side View) Buffi...
Operation (continued) WARNING • To reduce the risk associated with shear, pinch, and entanglement hazards: − Turn air and electrical supplies off on associated equipment before performing any adjustments, maintenance, or servicing the machine or taping heads − Never attempt to work on the taping heads or load tape when the box drive system is running •...
Page 19
Operation (continued) Figure 3-4 Place tape roll on tape drum to dispense tape with adhesive side forward. Seat tape roll fully against back fl ange of drum. Adhere tape lead end to threading needle as shown. WARNING Figure 3-4 – Tape Loading/Threading •...
Maintenance WARNING • To reduce the risk associated with shear, pinch, and entanglement hazards: − Turn air and electrical supplies off on associated equipment before performing any adjustments, maintenance, or servicing the taping heads − Never attempt to work on the taping head or load tape while the box drive system is running •...
Maintenance (continued) WARNING • To reduce the risk associated with shear, pinch, and entanglement hazards: − Turn air and electrical supplies off on associated equipment before performing any adjustments, maintenance, or servicing the taping heads − Never attempt to work on the taping head or load tape while the box drive system is running •...
Adjustments WARNING • To reduce risk associated with shear, pinch, and entanglement hazards: - Turn air and electrical supplies off associated equipment before performing any adjustments, maintenance, or servicing the machine or taping heads. - Never attempt to work on the taping head or load tape while the box drive system is Figure 5-1 –...
Adjustments (continued) WARNING • To reduce risk associated with shear, pinch, and entanglement hazards: Turn air and electrical supplies off associated equipment before performing any adjustments, maintenance, or servicing the machine or taping heads. Never attempt to work on the taping head or load tape while the box drive system is running.
Adjustments (continued) WARNING One-Way Tension Roller • To reduce the risk associated with shear, pinch, and entanglement hazards: - Turn air and electrical supplies off associated equipment before perform- ing any adjustments, maintenance, or servicing the machine or taping heads. - Never attempt to work on the taping head or load tape while the box drive system is running...
Troubleshooting Troubleshooting Guide Cause Correction Problem The tape is threaded incorrectly The tape must go around the wrap The tape leg on the front of the case is too long roller before going around the one-way tension roller The tape tension is too low Adjust the one-way tension roller The knurled roller drags Check for adhesive build-up...
Page 26
Troubleshooting (continued) Troubleshooting Guide Cause Correction Problem There is excess tension on the Adjust the one-way tension roller Tape is tabbing on the trailing leg tape drum assembly and/or the and/or the tape drum assembly on the back of the box one-way tension roller assembly Rollers in the tape path do not Clean adhesive deposits from...
Spare Parts/Service Information Recommended Spare Parts Listed are a set of spare parts that will periodically require replacement due to normal wear. These parts should be ordered to keep the taping heads in production: AccuGlide™ HST 2 Inch Upper Taping Head Qty.
Refer to the fi rst page of this instruction manual "Replacement Parts and Service Information" for replacement parts ordering information. IMPORTANT – Not all the parts listed are normally stocked items. Some parts or assemblies shown are available only on a special order basis. Contact 3M/Tape Dispenser Parts to confi rm item availability. February 2010...
Page 29
Taping Head Assemblies - ™ AccuGlide HST 2 Inch Figure 10401 Figure 15322 (Upper) Figure 15323 (Lower) Figure 15320 (Upper) Figure 15321 (Lower) Figure 15319 Figure 15318 Figure 15317 February 2010 HST 2" Taping Head - NA...