3M AccuGlide II STD 3 Inch Instructions And Parts List
  1. Manuals
  2. Brands
  3. 3M Manuals
  4. Packaging equipment
  5. AccuGlide II STD 3 Inch
  6. Instructions and parts list
3M AccuGlide II STD 3 Inch Instructions And Parts List

3M AccuGlide II STD 3 Inch Instructions And Parts List

Upper and lower taping heads
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Instructions and Parts List
AccuGlide II
STD 3 Inch
Upper and Lower
Taping Heads
Type 39600
Serial No.
_____________________________________
For reference, record taping head(s) serial number(s) here.
3M Packaging Systems Division
3M Center, Building 220-8W-01
St. Paul, MN 55144-1000
TM
Important Safety
Information
Read "Important Safeguards",
page 2 and also operating
"Warnings", page 7
BEFORE INSTALLING OR
OPERATING THIS
EQUIPMENT.
Spare Parts
It is recommended you
immediately order the
spare parts listed on
page 17. These parts are
expected to wear through
normal use, and should
be kept on hand to minimize
production delays.
AccuGlide
™
is a Trademark of
3M, St. Paul, MN 55144-1000
Litho in U.S.A
© 3M 1998 44-0009-1922-3(C28.0)

Advertisement

Table of Contents
loading

Related Manuals for 3M AccuGlide II STD 3 Inch

Summary of Contents for 3M AccuGlide II STD 3 Inch

  • Page 1 Serial No. _____________________________________ For reference, record taping head(s) serial number(s) here. AccuGlide ™ is a Trademark of 3M Packaging Systems Division 3M, St. Paul, MN 55144-1000 Litho in U.S.A 3M Center, Building 220-8W-01 St. Paul, MN 55144-1000 © 3M 1998 44-0009-1922-3(C28.0)
  • Page 2 Minimum billing on parts orders will be $25.00. Replacement part prices available on request. $10.00 restocking charge per invoice on returned parts. Note : Outside the U.S., contact the local 3M subsidiary for parts ordering information. "3M-Matic", "AccuGlide" and “Scotch” are trademarks of 3M Packaging Systems Division 3M, St.
  • Page 3 Replacement Parts And Service Information To Our Customers: This is the 3M-Matic™/AccuGlide™/Scotch™ brand equipment you ordered. It has been set up and tested in the factory with "Scotch" brand tapes. If any problems occur when operating this equipment, and you desire a service call, or phone consultation, call, write or Fax the appropriate number listed below.

  • Page 4: Table Of Contents

    Instruction Manual ™ AccuGlide II STD 3 Inch Upper and Lower Taping Heads Type 39600 Table of Contents Page Equipment Warranty and Limited Remedy ..................... Taping Head Contents ..........................Intended Use ............................Important Safeguards ..........................Specifications ............................3 - 4 Dimensional Drawing ........................

  • Page 5: Equipment Warranty And Limited Remedy

    3M is notified of the problem no later than five (5) calendar days after the warranty period. If 3M is unable to repair or replace the part within a reasonable time, then 3M, at its option, will replace the equipment or refund the purchase price.

  • Page 6: Intended Use

    Upper and Lower Taping Heads is to apply a "C" other than 3M-Matic™ case sealers. This includes clip of Scotch™ brand pressure-sensitive film box sealing tape to the top and/or bottom center seam of replacement of other types of taping, gluing or regular slotted containers.

  • Page 7: Important Safeguards

    Important Safeguards This safety alert symbol identifies important safety messages in this manual. READ AND UNDERSTAND THEM BEFORE INSTALLING OR OPERATING THIS EQUIPMENT. Important – In the event the following safety labels are damaged or destroyed, they must be replaced to ensure operator safety. See Parts Drawing/Lists, pages 18-35 for label part numbers.

  • Page 8: Specifications

    Case Sealer Width – 150 mm [6 inches] When upper and lower taping heads are used on “3M-Matic” case sealers, refer to the respective instruction manual specifications for box weight and size capacities. Operating Rate: Conveyor speeds up to 0.40 m/s [80 FPM] maximum.

  • Page 9: Dimensional Drawing

    Specifications (Continued) Figure 2-1 – Dimensional Drawing...

  • Page 10: Installation

    70 mm [2-3/4 inches], the taping file a damage claim immediately with the heads must be completely staggered so only transportation company and also notify your 3M one tape seal is being applied at one time. Representative. Note – AccuGlide™ II STD taping Heads are supplied with a buffing arm guard.

  • Page 11: Operation

    Operation Figure 3-1 – Taping Head Components/Threading Diagram, Upper Head (Left Side View) Figure 3-2 – Taping Head Components/Threading Diagram – Lower Head (Left Side View)

  • Page 12: Tape Loading - Upper Taping Head

    Operation (Continued) WARNINGS 1. Turn air and electrical supplies off and disconnect before servicing taping heads. 2. Never attempt to work on the taping heads or load tape when the box drive system is running. 3. Taping heads are equipped with an extremely sharp cut-off knife. Before working with the taping heads or attempting to load/thread tape, refer to Figures 3-1 and 3-2 and identify the knife location.
  • Page 13 Operation (Continued) Figure 3-4 Place tape roll on tape drum to dispense tape with adhesive side forward. Seat tape roll fully against back flange of drum. Adhere tape lead end to threading needle as shown. Figure 3-4 – Tape Loading/Threading Figure 3-5 WARNING –...

  • Page 14: Maintenance

    Maintenance WARNINGS 1. Turn air and electrical supplies off and disconnect before beginning maintenance. 2. Use care when working near tape cut-off knife as knife is extremely sharp. 3. Failure to comply with these warnings could result in severe personal injury or equipment damage.

  • Page 15: Lubrication

    Maintenance (Continued) WARNINGS 1. Turn air and electrical supplies off and disconnect before beginning maintenance. 2. Use care when working near tape cut-off knife as knife is extremely sharp. 3. Failure to comply with these warnings could result in severe personal injury or equipment damage.

  • Page 16: Adjustments

    Adjustments WARNING – Turn air and electrical supplies off and disconnect before beginning adjustments. Failure to comply with this warning could result in severe personal injury and/or equipment damage. Tape Web Alignment – Figure 5-1 The STD tape drum assembly is pre-set to accommodate 72 mm [3 inch] wide tape.

  • Page 17: Applying Mechanism Spring

    Adjustments (Continued) WARNING – Turn air and electrical supplies off and disconnect before beginning adjustments. Failure to comply with this warning could result in severe personal injury and/or equipment damage. Applying Mechanism Spring To obtain access to the spring, remove the taping head cover (four mounting screws).

  • Page 18: Tape Leg Length

    Adjustments (Continued) WARNING – Turn air and electrical supplies off and disconnect before beginning adjustments. Failure to comply with this warning could result in severe personal injury and/or equipment damage. Tape Leg Length WARNING – Use care when working near cut-off knife as knife is extremely sharp.
  • Page 19 THIS PAGE IS BLANK...

  • Page 20: Troubleshooting

    Troubleshooting Troubleshooting Guide Problem Cause Correction The tape is threaded incorrectly The tape must go around the wrap The tape leg on the front of the roller before going around the case is too long one-way tension roller The tape tension is too low Adjust the one-way tension roller The knurled roller drags Check for adhesive build-up...
  • Page 21 Troubleshooting (Continued) Troubleshooting Guide Cause Correction Problem There is excess tension on the Adjust the one-way tension roller Tape is tabbing on the trailing leg tape drum assembly and/or the and/or the tape drum assembly on the back of the box one-way tension roller assembly Rollers in the tape path do not Clean adhesive deposits from the...

  • Page 22: Spare Parts/Service Information

    Spare Parts/Service Information Recommended Spare Parts A set of spare parts that will periodically require replacement due to normal wear is supplied with the taping heads. The set includes the following which should be reordered when used to keep the taping heads in production: AccuGlide™...

  • Page 23: Replacement Parts Illustrations And Parts List

    Refer to the first page of this instruction manual "Replacement Parts and Service Information" for replacement parts ordering information. IMPORTANT – Not all the parts listed are normally stocked items. Some parts or assemblies shown are available only on a special order basis. Contact 3M/Tape Dispenser Parts to confirm item availability.
  • Page 24 ™ Taping Head Assemblies – AccuGlide II STD 3 Inch...
  • Page 25 Figure 2948 – Upper Head...
  • Page 26 Figure 2948 – Upper Head Ref. No. 3M Part No. Description 2948-1 78-8070-1386-3 Frame – Tape Mount Upper Assembly 2948-2 78-8070-1387-1 Frame – Front Upper Assembly 2948-3 78-8068-4143-9 Guide – #1 2948-4 78-8068-4144-7 Guide – #2 2948-5 83-0002-7336-3 Screw – Hex Hd, M4 x 14...
  • Page 27 Figure 2949 – Upper and Lower Heads...
  • Page 28 Figure 2949 – Upper and Lower Heads Ref. No. 3M Part No. Description 2949-1 78-8100-0982-5 Arm – Applying, R/H 2949-2 78-8100-0983-3 Arm – Applying, L/H 2949-3 78-8070-1292-3 Plate – Back-Up 2949-4 78-8076-4736-3 Shaft Roller 2949-5 78-8076-4737-1 Roller Assembly – Knurled...
  • Page 29 Figure 2950 – Upper Head...
  • Page 30 Figure 2950 – Upper Head Ref. No. 3M Part No. Description 2950-1 78-8070-1392-1 Buffing Arm – Sub Assembly 2950-2 78-8070-1391-3 Buffing Arm – Sub Assembly 2950-3 78-8091-0799-4 Shaft – 10 x 85, W/Hexagon 2950-4 78-8054-8807-5 Bushing – Buffing Roller 2950-5 78-8057-6180-2 Roller –...
  • Page 31 Figure 2951 – Upper and Lower Heads...
  • Page 32 Figure 2951 Upper and Lower Heads – Ref. No. 3M Part No. Description 2951-1 78-8070-1388-9 Link – Arm Bushing Assembly 2951-2 78-8070-1389-7 Link – Arm Bushing Assembly 2951-3 78-8076-4740-5 Shaft – Pivot 2951-4 78-8017-9082-1 Bearing – Special 30 mm 2951-5 78-8017-9106-8 Screw –...
  • Page 33 Figure 2952 – Upper and Lower Heads...
  • Page 34 Figure 2952 – Upper and Lower Heads Ref. No. 3M Part No. Description 2952-1 78-8070-1283-2 Frame – Cut-Off 2952-2 78-8028-7899-7 Knife – 89 mm/3.5 Inch 2952-3 26-1002-5817-2 Screw – Hex Hd, M5 x 8 2952-4 78-8076-4741-3 Knife Guard Assembly – W/English Language Label...
  • Page 35 Figure 2953 – Upper and Lower Heads...
  • Page 36 Figure 2953 – Upper and Lower Heads Ref. No. 3M Part No. Description 2953-1 78-8070-1395-4 Bracket – Bushing Assembly 2953-2 78-8060-8462-6 Shaft – Tape Drum, 3 Inch Head 2953-3 78-8017-9169-6 Nut – M18 x 1 2953-4 78-8076-4731-4 Tape Drum Assembly – 3 Inch Wide...
  • Page 37 Figure 2954 – Lower Head...
  • Page 38 Figure 2954 – Lower Head Ref. No. 3M Part No. Description 2954-1 78-8070-1369-9 Frame – Tape Mount Lower Assembly 2954-2 78-8070-1370-7 Frame – Front Lower Assembly 2954-3 78-8068-4144-7 Guide – #2 2954-4 78-8068-4143-9 Guide – #1 2954-5 83-0002-7336-3 Screw – Hex Hd, M4 x 14...
  • Page 39 Figure 2955 – Lower Head...
  • Page 40 Figure 2955 – Lower Head Ref. No. 3M Part No. Description 2955-1 78-8070-1391-3 Buffing Arm Sub Assembly 2955-2 78-8070-1392-1 Buffing Arm Sub Assembly 2955-3 78-8091-0799-4 Shaft – 10 x 85, W/Hexagon 2955-4 78-8054-8807-5 Bushing – Buffing Roller 2955-5 78-8057-6180-2 Roller – Buffing...

Table of Contents