Table of Contents
Advertisement
Quick Links
Instructions and Parts List
AccuGlide
HST
HST
Taping Heads
Type 39100
3M Masking and Packaging Systems Division
3M Center Bldg. 220-8W-01
St. Paul, MN 55144-1000
TM
(Upper)
(Lower)
Rev # is F106.05 here, but it is
E79.0 on the following page, and
it is D79.0 on the page after that.
Important
Safeguards
Turn to page four
for operating
safety information.
Important
It is recommended you
immediately order the
spare parts listed on
page 21. These parts
are expected to wear
through normal use,
and should be kept on
hand to minimize
production delays.
"AccuGlide" is a Trademark of 3M,
St. Paul, MN 55144-1000
Litho in U.S.A
© 3M 1996 34-7004-7499-1(F106.05)
Advertisement
Table of Contents
Related Manuals for 3M AccuGlide HST 39100
Summary of Contents for 3M AccuGlide HST 39100
- Page 1 Rev # is F106.05 here, but it is E79.0 on the following page, and it is D79.0 on the page after that. "AccuGlide" is a Trademark of 3M, 3M Masking and Packaging Systems Division St. Paul, MN 55144-1000 3M Center Bldg. 220-8W-01 Litho in U.S.A...
- Page 2 Minimum billing on parts orders will be $25.00. Replacement part prices available on request. $10.00 restocking charge per invoice on returned parts. Note : Outside the U.S., contact the local 3M subsidiary for parts ordering information. is this page and the following page redundant? they seem very similar "3M-Matic", "AccuGlide"...
- Page 3 Replacement Parts And Service Information To Our Customers: This is the 3M-Matic™/AccuGlide™/Scotch™ brand equipment you ordered. It has been set up and tested in the factory with "Scotch" brand tapes. If any problems occur when operating this equipment, and you desire a service call, or phone consultation, call, write or Fax the appropriate number listed below.
-
Page 4: Table Of Contents
Instruction Manual HST Taping Head (Upper) HST Taping Head (Lower) Type 39100 Table of Content Page Taping Head Contents ........................Equipment Warranty and Limited Remedy ..................Description ............................Important Safeguards ........................Specifications ............................ Installation ............................6 - 7 Special Use Set-Up HST Upper Taping Head –... -
Page 5: Taping Head Contents
Taping Head Contents HST Taping Head (Upper) Consists Of: Qty. Part Name Taping Head Assembly Tape Drum and Bracket Assembly Blade – 2.5 inch [64,5 mm] Lg. (Spare) Compression Spring (Upper taping head for side mounting – see page 9) HST Taping Head (Lower) Consists Of: Qty. -
Page 6: Equipment Warranty And Limited Remedy
3M. A part will be presumed to have become defective after the warranty period unless the part is received or 3M is notified of the problem no later than five (5) calendar days after the warranty period. If 3M is unable to repair or replace the part within a reasonable time, then 3M, at its option, will replace the equipment or refund the purchase price. -
Page 7: Description
AccuGlide HST Taping Heads (Upper and Lower), Type 39100 Description The AccuGlide HST Taping Heads (Upper and Lower) were designed to replace taping, gluing, and stapling heads in existing Case Sealing Machines. These high-speed heavy duty heads apply a “C” clip of Scotch brand pressure-sensitive film box sealing tape to the top and/or bottom center seam of regular slotted containers at speeds up to 150 ft./min. -
Page 8: Important Safeguards
Important Safeguards Both the upper and lower taping heads have important safeguards listed below, that every person who operates and/or maintains the heads should be familiar with. The “Warning – Sharp Knife” label is used on each head to warn operators and service personnel of the extremely sharp blades used to cut the tape at the end of the box sealing operation. -
Page 9: Specifications
Specifications These specifications apply to all HST Upper and Lower taping heads except where noted. Tape: For use with Scotch brand pressure-sensitive film box sealing tapes. Tape Width: 1 1/2 inches or 36 mm minimum to 2 inches [50 mm] maximum. Tape Roll Diameter: Position A –... -
Page 10: Installation
Installation Figure 2-1 – Taping Head Assemblies – Typical Mounting Dimensions... - Page 11 If this is not possible, contact 3M for assistance or suggested modifications that will provide ad- equate operating clearance to the taping head assembly.
- Page 12 THIS PAGE IS BLANK...
-
Page 13: Special Use Set-Up
Special Use Set-Up Instructions HST Upper Taping Head – Compression Spring Refer to Figure 3-1 WARNING – UPPER TAPING HEAD UTILIZES AN EXTREMELY SHARP KNIFE BLADE LOCATED UNDER THE ORANGE BLADE GUARD WHICH HAS THE “WARNING - SHARP KNIFE” LABEL. USE CARE WHEN WORKING NEAR BLADE. -
Page 14: Set-Up Procedure
Set-Up Procedure Figure 4-1 – Tape Threading Diagram – Upper Taping Head Figure 4-2 – Tape Threading Diagram – Lower Taping Head... -
Page 15: Tape Loading
Set-Up Procedure (Continued) Tape Loading The HST taping head accommodates up to 2 inch [50 mm] wide tape rolls. WARNING BOTH THE UPPER AND LOWER TAPING HEADS UTILIZE EXTREMELY SHARP KNIFE BLADES WHICH ARE LOCATED UNDER THE ORANGE BLADE GUARD WITH THE “WARNING –w SHARP KNIFE”... -
Page 16: Adjustments
Adjustments WARNING – NEVER ATTEMPT TO WORK ON THE TAPING HEADS WHEN THE BOX DRIVE SYSTEM IS RUNNING. INJURY TO PERSONNEL OR EQUIPMENT DAMAGE CAN POTENTIALLY RESULT. Tape Web Alignment Refer to Figure 5-1 The HST tape drum assembly is pre-set to accommodate 2 inch [50 mm] wide tape. -
Page 17: Buffing Roller Spring Tension
Adjustments (Continued) Buffing Roller Spring Tension Refer to Figures 5-3 and 5-4 WARNING – USE CARE WHEN WORKING ON BUFFING ROLLER ASSEMBLY AS SPRING IS UNDER TENSION. IF CARE IS NOT TAKEN PERSONNEL INJURY COULD RESULT. The buffing roller spring controls the buffing roller pressure on the box and returns the assembly to the reset position. -
Page 18: Tape Application Leg Length
Adjustments (Continued) Tape Application Leg Length Refer to Figure 5-5 The conveyor speed, at which the product moves through the taping heads, affect the leading and trailing tape application leg length. For best tape application performance, the taping heads should maintain tape leg lengths of 2 3/4 inch ±... -
Page 19: One-Way Tension Roller Assembly
Adjustments (Continued) One Way Tension Roller Assembly Refer to Figure 5-7 The one way tension roller is factory set. When replacing this assembly, the roller must have 1 lb. [0,5 kg] tangential force when turning. To Set Tension Wrap a cord or small strap (non-adhesive) 4-6 turns around the tension roller. - Page 20 THIS PAGE IS BLANK...
-
Page 21: Maintenance
Maintenance The taping heads have been designed for long, trouble free service. The taping head will perform best when it receives routine maintenance and cleaning. Taping head components that fail or wear excessively should be promptly repaired or replaced to prevent damage to other portions of the head or to the product. WARNING –... - Page 22 Maintenance (Continued) Figure 6-1 – Blade Replacement...
-
Page 23: Blade Replacement
Maintenance (Continued) WARNING – TURN OFF ELECTRICAL POWER SUPPLY AND DISCONNECT POWER CORD FROM ELECTRICAL SUPPLY BEFORE BEGINNING MAINTENANCE. IF POWER CORD IS NOT DISCONNECTED, SEVER INJURY TO PERSONNEL COULD RESULT. USE CARE WHEN REPLACING BLADES AS BLADES ARE EXTREMELY SHARP. IF CARE IS NOT TAKEN, SEVERE INJURY TO PERSONNEL COULD RESULT. -
Page 24: Lubrication
Maintenance (Continued) Lubrication Refer to Figure 6-2 Like most other equipment, the taping head must be properly lubricated to insure long, trouble free service. Figure 6-2 illustrates points which should be lubricated every 250 hours of operation. Lubricate the rotating and pivoting points noted by the arrows ( ) with SAE #30 non-detergent oil. -
Page 25: Replacement Parts And Service Information
Replacement Parts And Service Information Spare Parts A set of spare parts that will periodically require replacement due to normal wear is supplied with the taping heads. The set includes the following which should be reordered as consumed to keep the taping heads in production: HST Taping Heads (Upper and Lower) Qty. - Page 26 THIS PAGE IS BLANK...
- Page 27 Refer to first page of this instruction manual for parts ordering address and/or phone/fax number. IMPORTANT – Not all the parts listed are normally stocked items. Some parts or assemblies shown are available only on a special order basis. Contact 3M/Tape Dispenser Parts to confirm item availability.
- Page 28 THIS PAGE IS BLANK...
- Page 29 HST, Type 39100 Taping Head Assemblies...
- Page 30 HST, Type 39100 Figure 7...
- Page 31 Figure 7 – HST, Type 39100 Ref. No. 3M Part No. Description 78-8057-5701-6 Stud – Mounting 78-8057-5702-4 Pin – Mounting 78-8062-3810-7 Roller –Tension, Lower Head 78-8070-1401-0 Roller – Tension, Upper Head 78-8062-3840-4 Shaft – Tension Roller 78-8070-1268-3 Washer – Tension Roll Back-Up 78-8005-6119-9 Washer –...
- Page 32 HST, Type 39100 Figure 8...
- Page 33 Figure 8 – HST, Type 39100 Ref. No. 3M Part No. Description 78-8062-4155-6 Bearing Block Assembly, Lower Head 78-8062-4156-4 Bearing Block Assembly, Upper Head 78-8055-0976-3 Catch – Latch 78-8070-1614-8 Shaft – Roller, Knurled 78-8070-1402-8 Roller – Knurled 78-8055-0983-9 Applying Arm Block Assembly...
- Page 34 HST, Type 39100 Figure 9...
- Page 35 Figure 9 – HST, Type 39100 Ref. No. 3M Part No. Description 78-8070-1450-7 Blade Guard Assembly, Lower 78-8070-1602-3 Blade Guard Assembly, Upper 78-8070-1430-9 Spring – Torsion, Lower 78-8079-5381-1 Spring – Torsion, Upper 78-8070-1436-6 Shaft 78-8070-1449-9 Frame – Cut-off Weldment, Lower 78-8070-1601-5 Frame –...
- Page 36 HST, Type 39100 Figure 10...
- Page 37 Figure 10 – HST, Type 39100 Ref. No. 3M Part No. Description 78-8062-3992-3 Buffing Arm Assembly, Lower 78-8079-5221-9 Buffing Arm Assembly, Upper 78-8070-1499-4 Bumper – Buffing 78-8055-0970-6 Pin – Buffing 78-8055-0969-8 Shaft – Buffing Arm 78-8015-7213-8 Spring – Torsion Inner, Lower 78-8068-3940-9 Spring –...
- Page 38 HST, Type 39100 Figure 11...
- Page 39 Figure 11 – HST, Type 39100 Ref. No. 3M Part No. Description 78-8070-1618-9 Bracket – Tape Drum 78-8017-9169-6 Nut – Hex M18 x 1 78-8076-4519-3 Shaft – Tape Drum 78-8052-6749-5 Tape Drum Assembly 78-8052-6268-6 Leaf Spring 26-1002-5753-9 Screw – Self Tapping 78-8060-8172-1 Washer –...