Download
Share
Print this page
Sundstrom SR 591 Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Sundstrom Manuals
  4. Welding Accessories
  5. SR 591
  6. Operating instructions manual

Sundstrom SR 591 Operating Instructions Manual

Welding shield
Hide thumbs Also See for SR 591:

Advertisement

Quick Links

Download this manual
Operation instruction
SR 591
Welding Shield
Revision: 02
OI06H-4318 SR 591
1
2020-05-07

Advertisement

loading
Need help?

Need help?

Do you have a question about the SR 591 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Sundstrom SR 591

Summary of Contents for Sundstrom SR 591

  • Page 1 Operation instruction SR 591 Welding Shield Revision: 02 OI06H-4318 SR 591 2020-05-07...

  • Page 2: General Information

    The welding shields are designed specifically for protection against radiation and spatter during welding, flame-cutting and similar work When selecting equipment for SR 591 some of the factors that should be considered are as follows: • Type of pollutant • Concentrations •...
  • Page 3 Unpacking SR 591 Packing list: • Welding shield • User instruction • Cleaning tissue OI06H-4318 SR 591 2020-05-07...
  • Page 4 The space to the shield. 1.2 How high the welding 1.4 Width adjustment of the shield sits on the head. head harness. The angle against the shield. Adjustment of the width of the head harness. OI06H-4318 SR 591 2020-05-07...
  • Page 5 2. Putting the welding shield on 2.1 Raise the visor and put the welding shield on. Adjustment of the circumference of the head harness by means of the knob at the rear of the head harness. 2.2 Lower the visor OI06H-4318 SR 591 2020-05-07...
  • Page 6 3. Change the welding filter 3.1 Loosen the screw in the 3.3 Fit the welding filter. holder for the welding filter. Fit the holder. Tighten the screw 3.2 Release the holder for the welding filter. OI06H-4318 SR 591 2020-05-07...
  • Page 7 4.3 Fit the new inner holder for the welding filter. protective lens on the inside of the welding filter. 4.2 Release the holder for the 4.4 Fit the protective lens. welding filter. Fit the holder. Tighten the screw. OI06H-4318 SR 591 2020-05-07...
  • Page 8 5.3 Fit the new correction holder for the welding filter. lens on the inside of the welding filter. 5.2 Release the holder for the 5.4 Fit the correction lens. welding filter. Fit the holder. Tighten the screw. OI06H-4318 SR 591 2020-05-07...
  • Page 9 6.1 Loosen the screw in the 6.3 Release and remove the holder for the welding filter. outer protective lens 6.2 Release the holder for the 6.4 Fit the protective lens. welding filter. Fit the holder. Tighten the screw. OI06H-4318 SR 591 2020-05-07...
  • Page 10 7. Change the sweatband 7.1 Remove the sweatband 7.2 Fit the sweatband on the head harness. OI06H-4318 SR 591 2020-05-07...
  • Page 11 8.2 Fit a new sweatband See Change the sweatband. Secure the two fixing points of the head harness. OI06H-4318 SR 591 2020-05-07...
  • Page 12 If necessary, spray the face shield with 70 % ethanol or isopropanol scratching. Automatic welding solution for disinfection filters are very sensitive to NOTE! Never use solvents for cleaning moisture. Use only a dry polishing cloth. 9.1 Sundström cleaning tissues SR 5226 are recommended for daily care. OI06H-4318 SR 591 2020-05-07...

  • Page 13: Maintenance Schedule

    10. Maintenance schedule 10.1 Recommended minimum requirements on Before use After use Annually maintenance routines so you will be certain that the • • Visual inspection • equipment will always be in usable condition. • Cleaning • OI06H-4318 SR 591 2020-05-07...