Table of Contents

Advertisement

operator's manual
16L

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TWD1672GE and is the answer not in the manual?

Questions and answers

Summary of Contents for Volvo Penta TWD1672GE

  • Page 1 operator’s manual...
  • Page 2 Do not modify or tamper with the exhaust system. • Do not idle the engine except as necessary. For more information www.P65warnings.ca.gov/marine www.p65warnings.ca.gov/products/diesel © 2022 AB VOLVO PENTA Volvo reserves the right to make changes Printed on environmentally friendly paper...
  • Page 3: Table Of Contents

    Maintenance and replacement parts ............14 Excessive strain on a product and components ........15 Emission Aftertreatment System ............. 17 Emergency Situation Inducement Override ..........18 Volvo Penta Dealer Network ..............21 Volvo Penta Action Service ..............21 Presentation ....................22 Engines ....................22 EMS (Engine Management System) ............
  • Page 4 Lubrication System ................85 Fuel System ................... 86 Cooling System ..................88 Coolant, Mixing ..................88 Water Quality ..................89 Inlet and Exhaust System ..............90 Electrical System .................. 90 Identification Numbers ................. 91 Index ......................95 47711094 08-2022 © AB VOLVO PENTA...
  • Page 5: Foreword

    Pay careful attention to the safety instructions included in the manual. As the owner of a Volvo Penta engine, you become part of a worldwide network of dealers and service workshop that assist you with technical advice, service requirements and replacement parts.
  • Page 6: Safety Information

    This chapter describes how safety precautions are If anything remains unclear or if you are unsure of presented in the manual and on the product. Read the something, contact your Volvo Penta dealer for chapter through very carefully before you start the assistance.
  • Page 7 Always wear safety glasses if there is a risk of splintering, sparks and spray from the electrolyte (so- called battery acid), or other chemicals. Your eyes are very delicate and damage can result in loss of sight! 47711094 08-2022 © AB VOLVO PENTA...
  • Page 8 Spare parts — safety WARNING! Always use spare parts with the same quality as genuine Volvo Penta parts to minimize the risk of an explosion or fire. Components in fuel systems and electrical systems on Volvo Penta engines are designed and manufactured to minimize the risk of explosions and fire, in accordance with applicable legal requirements.
  • Page 9 Information on the engine IMPORTANT: Make sure that all warning and information decals on the product are always visible. Replace decals which have been damaged or painted over. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 10 Before welding work IMPORTANT: Before any work with electric weld can begin, the connection to all control units must be disconnected. After finished welding, re-connect the connection to all control units before connecting any battery cable. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 11 Smoking is forbidden and the engine must be stopped. Proper fuel quality IMPORTANT: Always use the fuel recommended by Volvo Penta. See Technical Data in Operator’s Manual. Other fuel can damage the engine. Wrong fuel quality can also lead to higher service costs.
  • Page 12 If it comes electrolyte to unprotected skin, wash immediately with soap and water. Layout of the battery compartment IMPORTANT: Make sure the battery compartment is designed according to current safety standards. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 13 Cleanliness for sensitive components IMPORTANT: Observe meticulous cleanliness when handling system components. Even minimal amounts of dirt could cause a breakdown. Adjustment of the clutch CAUTION! Clutch adjustments must be carried out with the engine stopped. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 14: Introduction

    To retain the dependability and exhaust emission control originally built into all Volvo Penta engines, it is essential that the engines and receive periodic maintenance according to the maintenance instructions.
  • Page 15: Fuel, Oils And Coolant

    For more information regarding our different Services, visit volvopenta.com or contact your Volvo Penta representative. Running in the engine The engine must be run in during its first 10 operating hours, as follows: Run the engine in normal operations.
  • Page 16: Maintenance And Replacement Parts

    These qualities will be maintained through regular servicing and the use of spare parts with the same quality as genuine Volvo Penta parts. If reliable and purpose-built parts are not used, your safety, health, and the machine’s function may be compromised.
  • Page 17: Excessive Strain On A Product And Components

    Environmental care Environmental care is a core value at Volvo Penta. Energy efficiency and low emissions are among the most important product related aspects and priority focus areas for Volvo Penta business. Several of the global challenges the world faces are directly or indirectly related to power industries and transports.
  • Page 18 NOTICE! Neglects or failure to follow the points listed here may invalidate the engine emission certificate. This means AB Volvo Penta can no longer guarantee engine conformity with the certified model. Volvo Penta is not responsible for damages or costs arising as a result of this.
  • Page 19: Emission Aftertreatment System

    If the exhaust gas control system does not work correctly the operator will be informed by a fault indication. ® 1. AdBlue = Registered trademark of the Verband der Automobilindustrie e.V. (VDA ). 2. DEF = Diesel Exhaust Fluid 47711094 08-2022 © AB VOLVO PENTA...
  • Page 20: Emergency Situation Inducement Override

    120 hours in a single activation. Once deactivated, either by the operator or by reaching 120 hours, it cannot be reactivated without contacting an authorized Volvo Penta dealer to reset the function to its original 120 hours. Federal regulations prohibit activating the emergency inducement override for something other than a qualified emergency situation.
  • Page 21 Volvo Penta will send the information from the operator's report to US EPA and California ARB. Federal regulation separately prohibits submitting false information.
  • Page 22 After Treatment system. Special maintenance is required after deactivation of the Emergency Situation Inducement Override function. Please contact an authorized Volvo Penta dealer for inspection and repair. NOTICE! Operation and maintenance of engine in a manner not specified by these special maintenance instructions could result in a violation of law subject to penalties.
  • Page 23: Volvo Penta Dealer Network

    The Volvo Penta global network of authorized dealers is at your service. We strongly recommend that you take your product to an authorized Volvo Penta dealer for service and repair. They are specialists in Volvo Penta products and have the accessories, genuine...
  • Page 24: Presentation

    They are equipped with electronic management systems (EMS), turbochargers, charge air coolers, thermostatically controlled cooling systems and electronic speed control. To reduce emissions, the engines are equipped with EATS systems. Refer to Presentation, page 24. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 25: Ems (Engine Management System)

    EMS is an electronic system with CAN communication (Controller Area Network) for diesel engine control. The system has been developed by Volvo Penta and includes fuel regulation and diagnostic functions. The system consists of a control unit, injectors, a number of sensors that supply the control unit with information, and connectors for diagnostics and functional checks.
  • Page 26: Eats (Exhaust Aftertreatment System)

    Should the system detect deviations, the maximum engine torque and engine speed will be reduced and a fault code stored in the control unit. For further information refer to EATS Inducements, page 51. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 27: Overview

    The system comprises: 1 AdBlue®/DEF Tank 2 AdBlue®/DEF Pump 3 AdBlue®/DEF Injector 4 EATS Catalyst and Muffler 5 Catalytic Converter The atomized urea solution is sprayed into the exhaust gases upstream of the catalytic converter. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 28: Tank

    EATS system, as the remaining solution will circulate and cool the system. However, emissions from the engine will increase as the injection valve is closed and no exhaust aftertreatment will take place. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 29 25 °C (77 °F) or in direct sunlight. Remember that the solution expands upon freezing and to leave room for expansion in the tank when storing in spaces where there is a risk of freezing. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 30: Operation

    IMPORTANT: AdBlue®/DEF spillages may not be washed into drains. If a spill should occur, the solution must be absorbed using dry sand or other non-flammable material and handled according to local and national regulations. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 31 — flush with copious amounts of water and remove contaminated clothing. • eye contact — flush thoroughly for several minutes; contact physician as necessary. • inhalation — breathe fresh air and contact physician as necessary. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 32: Instruments And Controls

    Instruments and Controls DCU II (Display Control Unit) The Volvo Penta DCU II instrument panel communicates with the engines control unit and has a number of functions as control, monitoring and diagnostics. NOTICE! Settings and the type of engine data presented on the display may vary depending on the installation and engine model.
  • Page 33 — Volvo Penta recommends to immediately contact a qualified workshop . • WARNING, yellow text, the system has detected a fault — Volvo Penta recommends to contact a qualified workshop as soon as possible. • MESSAGE, blue text, non-critical information message for the operator regarding operation of the Control Interface Panel.
  • Page 34 . This will also provied information about number of engine hours when the fault became active and the SPN and FMI codes. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 35 Volvo Penta technician. Refer to the installation manual for further engine information. Authorized Volvo Penta dealer or OEM only • I/O Status (I/O Status) •...
  • Page 36: Control Interface Module

    Instruments and Controls Control Interface Module The Volvo Penta Control Interface Module (CIM) instrument panel communicates with the engine control unit and has a number of functions as control, monitoring and diagnostics. NOTICE! Settings and the type of engine data presented on the display may vary depending on the installation and engine model.
  • Page 37 . • WARNING (WARNING), yellow text, the system has detected a fault — Volvo Penta recommends to contact a qualified workshop as soon as possible. • MESSAGE (MESSAGE), blue text, non-critical engine message for the operator.
  • Page 38 . This will also provied information about number of engine hours when the fault became active and the SPN and FMI codes. P0028065 47711094 08-2022 © AB VOLVO PENTA...
  • Page 39 • Engine Hardware ID (Engine Hardware ID) • CIM hardware ID (CIM hardware ID) • Engine Software ID (Engine Software ID) • CIM Software ID (CIM Software ID) • Chassis ID (Chassis ID) P0028160 47711094 08-2022 © AB VOLVO PENTA...
  • Page 40: Easy Link Instruments

    - Tachometer / hours counter (fault codes are also displayed on the tachometer display when the diagnostic button is pressed) - Coolant temperature - Oil pressure - Oil temperature - Battery voltage - Alarm panel - Turbo pressure 47711094 08-2022 © AB VOLVO PENTA...
  • Page 41: Starting

    2 If preheat is activated, wait until heating icon has disappeared until START is requested. 3 Press the START button to start the engine. START STOP P0018811 47711094 08-2022 © AB VOLVO PENTA...
  • Page 42: Starting Using Auxiliary Batteries

    Risk of arcing. Do not bend over any of the batteries either. 4 Remove the cables in the reverse order. IMPORTANT: The ordinary cables to the standard batteries must not under any circumstances be loosened. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 43: Operation

    The consequences can be carbon build-up on valves, piston crowns and the exhaust turbine, which could affect engine performance. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 44 • If visible slobber has occurred, it can be burned off by running the engine on at least 30% load for about 40-60 minutes. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 45: Engine Shutdown

    P0018811 Auxiliary Stop For location of the extra stop, refer to Maintenance, page 56. WARNING! Working with or approaching a running engine is a safety risk. Watch out for rotating components and hot surfaces. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 46: After Engine Shutdown

    If there is a risk of freezing, the coolant in the cooling system must have adequate antifreeze protection. Refer to Maintenance, page 67. IMPORTANT: A poorly charged battery can freeze and burst. Refer to Battery, page 80. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 47: Fault Handling

    The operator is warned that there is a malfunction via the instruments. Depending on the instrumentation in use, the fault message is shown in various ways. Fault codes can also be read out by the Volvo Penta diagnostic tool. Depending on the severity of the fault, the diagnostic function will take various actions to protect the engine and limit emissions (e.g.
  • Page 48: Dcu Ii (Display Control Unit)

    If so a new fault codes is registered. If a malfunction has not been corrected it will be registered once again and has to be acknowledged again. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 49: Fault Tracing

    Fault Tracing A number of symptoms and possible causes of engine malfunctions are described in the table below. Always contact your Volvo Penta dealer if any problems occur which you can not solve by yourself. IMPORTANT: Read through the instructions for care and maintenance in before starting work.
  • Page 50 25 High back pressure in the exhaust system 26 Break in ”Pot+” cable to throttle 27 High temperature, charge air cooler 28 Blocked radiator 29 No pressure in cooling system 30 Check wastegate function 47711094 08-2022 © AB VOLVO PENTA...
  • Page 51: Eats Warnings And Inducements

    EATS Inducements, page 51. NOTICE! Warning messages and symbols may vary depending on the installation; shown here are those seen on panels sold by Volvo Penta. Important! Take prompt action in case of error code indication. Warning Symbols Stimulus for power reduction warning.
  • Page 52: Quality Shortcomings And Component Defects

    Joint alignments should be checked and gaskets replaced before reassembly. For cases with deposits larger in size – please contact your local Volvo Penta representative to discuss the issue. Quality shortcomings and...
  • Page 53: Eats Inducements

    2 x 30 minutes. After 30 minutes the engine is shut down. Each 30-minute period requires a new manual activation. 7 If a fault returns within 40 hours, available running time will be reduced to 30 minutes. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 54 4 Following re-start, the engine will only run at idle. 5 When the fault is remedied, the engine will revert to full power. 6 If a fault returns within 40 hours, available running time will be reduced to 30 minutes. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 55: Fault Code Register

    3, 5 Fuel Injector, Cylinder #6 3, 5 Starter motor relay 3, 4, 5, 6 Starter element 5, 6, 7, 12 Engine stop switch 3, 4, 5, 11, 14 1188 Wastegate Valve 3, 4, 5 47711094 08-2022 © AB VOLVO PENTA...
  • Page 56 Engine Oil Pressure Before Filter 3, 4, 5, 11 520688 Aftertreatment Exhaust Temperature - Dry 0, 3, 4, 5, 16 520691 Torque Speed Control 1 Received With Errors (Counter or Checksum) Torque speed control 47711094 08-2022 © AB VOLVO PENTA...
  • Page 57: Maintenance Schedule

    Maintenance Schedule Your Volvo Penta engine and its equipment are designed for high reliability and long life. The engines are built to have the smallest possible environmental impact. If given preventive maintenance, according to the maintenance schedule, these qualities will be retained and unnecessary malfunctions will be avoided. In order for the warranty to be valid, the owner must make sure that the services in the service intervals are performed.
  • Page 58: Maintenance

    8 Fuel filter, with fuel pressure monitor 9 Fuel prefilter with water monitor 10 Oil dipstick 11 Air filter indicator 12 Low-Pressure Turbo 13 High-Pressure Turbo 14 Charge air cooler (Low-Pressure Turbo) 15 Oil filter P0020401 47711094 08-2022 © AB VOLVO PENTA...
  • Page 59: Engine, General

    Scrap the old filter. No cleaning or re-use is permissible • In continuous operation, the filter should be checked every 8 hours. For operations in extremely dirty environments such as coal mines and rock crushing mills, special air filters must be used. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 60: Charge Air Pipe, Leakage Check

    8 Lift the 1/2" wrench and install the new drive belt. 9 Install the belt guards. 10 Install the fan guard and fan ring round the cooling fan. 11 Start the engine and do a function check. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 61: Alternator Belt, Replace

    8 Lift the 1/2” wrench in the belt tensioner (2) and install the new water pump drive belt. 9 Install the belt guards. 10 Install the fan guard and fan ring round the cooling fan. 11 Start the engine and do a function check. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 62: Lubrication System

    Maintenance Lubrication System Volvo Penta only recommends the use of genuine Volvo Penta oils with the correct VDS (Volvo Drain Specification) standards. Genuine Volvo Penta oils are extensively tested and quality assured by Volvo Penta to optimize performance, reduce fuel consumption and maximize the life of the engine.
  • Page 63: Engine Oil, Replace

    Collect all the old oil and old filters, and hand them to a re-cycling station for destruction. 3 Remove the drain hose (or install the bottom drain plug). 4 Fill with engine oil. For change volume, please refer to Technical Data, page 85. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 64: Oil Filter/By-Pass Filter, Replace

    6 Top up with engine oil, start the engine and let it run for 20-30 seconds. 7 Turn off the engine, check the oil level and top up as required. 8 Check sealing round the oil filters. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 65: Fuel System

    NOTICE! Put a collection vessel under the fuel filter tocollect the condensate and fuel. 1 Open the drain nipple in the base of the fuel pre- filter. 2 Tighten the drain tap when fuel without water starts to run out. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 66: Engine Fuel Filter Replacement

    4 Lubricate the seal with diesel fuel and install the new fuel filter. Tighten the fuel filter in accordance with the instructions on the fuel filter. 5 If necessary, vent the fuel system, please refer to Fuel system, bleeding, page 66. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 67: Fuel Pre-Filter, Replace

    Then tighten a further half turn, no more. 7 Connect the cable to the water trap sensor. 8 If necessary, vent the fuel system, please refer to Bleeding the Fuel System. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 68: Fuel System, Bleeding

    4 Lock the hand pump, push down and twist the handle. 5 Start the engine and allow it to idle fast for about 10 minutes. 6 Perform a leakage and function check. P0025497 47711094 08-2022 © AB VOLVO PENTA...
  • Page 69: Cooling System

    - in the worst case - can cause engine breakdown. Volvo Penta strongly recommend the use of our own coolants, ”Volvo Penta Coolant VCS Ready Mixed” or the concentrate ”Volvo Penta Coolant VCS”, which...
  • Page 70: Coolant Level, Checking And Topping Up

    Steam or hot fluid could spray out. IMPORTANT: Only use coolant recommended by Volvo Penta. Top up with the same type of coolant as already used in the system. Different types of coolant must not be mixed.
  • Page 71 (4) these can also be used to fill the radiator. 4 Top up until the system is completely full. 5 Vent the system through openings on the expansion tank and radiator. P0020854 47711094 08-2022 © AB VOLVO PENTA...
  • Page 72: Coolant, Draining

    Do not use a high pressure power washer. Remove guards as necessary, to access the radiator. Clean with water and a mild detergent. Use a soft brush. Be careful not to damage the radiator vanes. Reinstall removed parts. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 73: Cooling System, Cleaning

    Make sure that the liquids mix. IMPORTANT: Always follow local safety instructions and regulations. Cooling performance is reduced by deposits in the radiator and cooling galleries. The cooling system should be cleaned out when the coolant is changed. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 74 1 Empty the cooling system. Refer to Coolant, Draining, page 70. 2 Put a hose into the expansion tank filling hole and flush with clean water, as specified by Volvo Penta– refer to section Water quality in Technical Data, page 88 until the water draining out is completely clear.
  • Page 75: Cooling Air Filter

    Allow it to act for a few minutes and then rinse with tap water. IMPORTANT: Do not use gasoline, steam, a high-pressure washer or other cleaning agents. 4 Re-install the filter according to instructions. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 76: Inlet And Exhaust System

    AdBlue®/DEF has been added to the tank. IMPORTANT: The use of solution that do not fulfill the ISO 22241 standard will compromise the aftertreatment system performance, increase emissions. Any warranty claims will be rejected. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 77 Damage and costs arising from a failure to meet these requirements are not covered by Volvo Penta warranty obligations. ® If AdBlue /DEF is filled from a can or pump that lacks...
  • Page 78: Adblue/Def-Pump Filter, Change

    ® emptying of the AdBlue /DEF hoses. Disconnect the battery negative terminal. P0019364 Place a collection vessel under the filter cover. Undo the filter cover NOTICE! Use approved safety equipment and receptacle. P0019389 47711094 08-2022 © AB VOLVO PENTA...
  • Page 79 Pull out the filter. P0019390 Install the new filter (1). Install the rubber gasket (2). Screw on the filter cover (3). P0019391 47711094 08-2022 © AB VOLVO PENTA...
  • Page 80 Tightening torque: 20 (+5) Nm (14.8 +3.68 Ibf. ft.) P0019392 Reconnect the battery negative terminal. Start the engine. Check for leaks; check function. Delete any fault codes. P0019365 NOTICE! Care for equipment and the remaining AdBlue®/DEF. p0013225 47711094 08-2022 © AB VOLVO PENTA...
  • Page 81: Electrical System

    Always stop the engine and break the current using the main switches before working on the engine. IMPORTANT: Contact a Volvo Penta dealer for information if any arc welding will be performed on the application. Arc welding can cause damage to the engine and the electronics.
  • Page 82: Battery

    NOTICE! If low starter battery alarm occur, the battery may get drained which might result in loss of functions and engine stopping. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 83 1 Connect the + cable (red) to the + pole on the battery and tighten the nut. 2 Connect the – cable (black) to the – pole on the battery and tighten the nut. NOTICE! Hand in the old battery to a re-cycling station. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 84: Storage

    It is of utmost importance that the conservation is performed correctly, therefore we have compiled a checklist covering the most important points. Before taking the engine out of service for long periods, Volvo Penta recommends that the engine is checked by a qualified workshop for possible need for overhaul or repair.
  • Page 85 2/3 diesel fuel. • Drain the conservation oil from the engine. • Bleed the fuel system. • Follow the other instructions on the previous page. * Conservation oils are sold by oil companies. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 86: Technical Data

    Stroke, mm (inch) 165 (6.50) 16,12 (983.9) Displacement, liter (inch Weight, dry, kg (lbs) 1810 (3990) Weight, wet, kg (lbs) 1890 (4167) Firing order 1-5-3-6-2-4 Compression ratio 16,8:1 Low idle, r/min. High idle, rpm 1800 47711094 08-2022 © AB VOLVO PENTA...
  • Page 87: Lubrication System

    Oil filter Full flow filter By-pass filter Lube oil pump Type Gear driven Oil recommendations Oil quality Oil change interval, reached first in operation: VDS-3 500 hours or 12 months VDS = Volvo Drain Specification 47711094 08-2022 © AB VOLVO PENTA...
  • Page 88: Fuel System

    Use of fuel that does not fulfil the requirements above will damage the SCR system. Damages and costs arising from a failure to meet the requirements above are not covered by Volvo Penta's warranty obligations. Never start the engine if incorrect fuel has been filled by mistake.
  • Page 89 Technical Data Restrictions for other diesel fuels Volvo Penta also approves the use of other diesel fuels as long as the here specified restrictions are followed. However Volvo Penta does not guarantee compliance with emission legislation or fulfillment of expected lifetime with these other diesel fuels.
  • Page 90: Cooling System

    Follow the mixing recommendation on the product. The coolant should be mixed with distilled, deionized water. For Volvo Penta specified water requirements; refer to Water Quality, page 89. NOTICE! Always use “Ready Mixed” coolant if water quality cannot be determined or if it does not fulfill ASTM D4985.
  • Page 91: Water Quality

    5.5–9 Silica (acc. ASTM D859) <20 mg SiO Iron (acc. ASTM D1068) <0.10 ppm Manganese (acc. ASTM D858) <0.05 ppm Conductivity (acc. ASTM D1125) <500 µS/cm Organic content, COD (acc. <15 mg KMnO ISO8467) 47711094 08-2022 © AB VOLVO PENTA...
  • Page 92: Inlet And Exhaust System

    2 pcs. series connected 12 V, max. 220 Ah Battery electrolyte density at +25°C ° fully charged battery 1,28 g/cm (1,24 g/cm recharge battery at 1,20 g/cm (1,20 g/cm * Note. Applies to batteries with tropical acid. 47711094 08-2022 © AB VOLVO PENTA...
  • Page 93: Identification Numbers

    B Engine Family C Power Category D Date of Manufacture (mm-yy) E Model Year F Generator (for GenSets and other applications) G Constant Speed (used in constant speed applications only) H Exhaust Emission Control System 47711094 08-2022 © AB VOLVO PENTA...
  • Page 94 Applied standards: EN 61000–6–1:2007, EN 61000–6–2:2005, EN 61000–6–3:2007, EN 61000–6–4:2007, EN 12895:2015 + A1:2019, EN-ISO 14982:2009 and EN 13766-1:2018. For engines equipped with the Volvo Penta Start/Stop System the responsibility for the functional safety of the system lies with the machine manufacturer performing the integration.
  • Page 95 Applied standards: EN 61000–6–1:2007, EN 61000–6–2:2005, EN 61000–6–3:2007, EN 61000–6–4:2007, EN 12895:2015 + A1:2019, EN-ISO 14982:2009 and EN 13766-1:2018. For engines equipped with the Volvo Penta Start/Stop System the responsibility for the functional safety of the system lies with the machine manufacturer performing the integration.
  • Page 96 Coolant, Draining............70 Tank................26 Cooling air filter............73 Cooling System........... 67, 88 Cooling System, Cleaning......... 71 Volvo Penta Action Service........21 Volvo Penta Dealer Network........21 DCU II (Display Control Unit)......30, 46 Diagnostic Function...........45 Warning Symbols............49 Draining condensate, fuel system......63 Water Quality.............89...
  • Page 99 ‫من الممكن طلب دليل المشغل بلغة أخرى مجا ن ً ا عبر اإلنترنت لفترة تصل إلى 21 شهر ً ا من بعد‬ http://manual.volvopenta.com/coupon/ .‫التسليم‬ Hvis det ikke er muligt at bestille via Internettet, bedes du kon- /http:// manual.volvopenta.com/coupon takte din Volvo Penta forhandler. .Volvo Penta ‫إذا كان الوصول إلى اإلنترنت غير متاح، فالرجاء االتصال بوكيل‬...

This manual is also suitable for:

Twd1673ge

Table of Contents