Related Manuals for Cherry Aerospace G84-LS
Summary of Contents for Cherry Aerospace G84-LS
- Page 1 TM-G84-LS Rev: G DCR# 15-0407 DATE: 4/30/15 Federal Identification Code: 11815 © 2015 Cherry Aerospace ORIGINAL INSTRUCTIONS G84-LS Split Riveter 1224 E. Warner Ave Santa Ana, CA 92705 www.cherryaerospace.com...
-
Page 2: Table Of Contents
TM-G84-LS Rev: G DCR# 15-0407 DATE: 4/30/15 Federal Identification Code: 11815 © 2015 Cherry Aerospace ® T H E C H E R R Y G 8 4 - L S S P L I T R I V E T E R TABLE OF CONTENTS Description ...................................... -
Page 3: Description
Federal Identification Code: 11815 © 2015 Cherry Aerospace DESCRIPTION The G84-LS is a powerful, rugged and compact split riveter designed for ergonomic, high speed and reliable operation. Adaptors are available for mounting most Cherry pulling heads; it will install most popular sizes and types of aircraft pull type fasteners including lock-bolts, blind-bolts, etc. -
Page 4: Recommended Usage
TM-G84-LS Rev: G DCR# 15-0407 DATE: 4/30/15 Federal Identification Code: 11815 © 2015 Cherry Aerospace PUTTING THE TOOL IN SERVICE The tool must be used with an air pressure regulator. Even if your shop air pressure is below the maximum recommended range, pressure spikes in your airlines could cause serious damage to the tool or cause safety concerns. -
Page 5: Maintenance And Repair
TM-G84-LS Rev: G DCR# 15-0407 DATE: 4/30/15 Federal Identification Code: 11815 © 2015 Cherry Aerospace MAINTENANCE AND REPAIR Note: Minor fluid loss over time at the piston rod is normal, and does not indicate seal damage. See troubleshooting guide (page 8) for simple tips on when tool maintenance or repair is necessary. -
Page 6: Bleeding
TM-G84-LS Rev: G DCR# 15-0407 DATE: 4/30/15 Federal Identification Code: 11815 © 2015 Cherry Aerospace FILL AND BLEED Figure 15 Figure 12 Figure 14 Figure 13 Figure 18 Figure 19 Figure 17 Figure 16 Figure 20 Required tools: Pressurized oil source with correct fitting (#10-32) A. - Page 7 TM-G84-LS Rev: G DCR# 15-0407 DATE: 4/30/15 Federal Identification Code: 11815 © 2015 Cherry Aerospace TOOL SERVICE Tool service is needed in case of tool malfunction, massive fluid loss or as part of your routine maintenance program. TOOLS NEEDED: G84-LSKT – tool kit, needle-nose pliers, G84-LSKS –...
-
Page 8: Head Sub-Assembly
TM-G84-LS Rev: G DCR# 15-0407 DATE: 4/30/15 Federal Identification Code: 11815 © 2015 Cherry Aerospace HEAD CYLINDER SUB-ASSEMBLY (744-202) Caution: Remove Pulling Heads or other attachments before attempting to disassemble. Disassembly instructions: • Remove screw (57) and unscrew lock ring (58) with spanner wrench 530-202. -
Page 9: Tool Care
TM-G84-LS Rev: G DCR# 15-0407 DATE: 4/30/15 Federal Identification Code: 11815 © 2015 Cherry Aerospace TOOL CARE This tool has been designed for optimum service with minimum care. In order to extend the life of the tool, please follow the simple instructions given below: •... - Page 10 TM-G84-LS Rev: G DCR# 15-0407 DATE: 4/30/15 Federal Identification Code: 11815 © 2015 Cherry Aerospace G84-LS CROSS SECTIONAL VIEW...
- Page 11 TM-G84-LS Rev: G DCR# 15-0407 DATE: 4/30/15 Federal Identification Code: 11815 © 2015 Cherry Aerospace PART LIST FOR THE G84-LS SPLIT RIVETER (744-190) ITEM PART NO. DESCRIPTION ITEM NO. PART NO DESCRIPTION 744-189 Sub-Assembly, Handle P268 O-Ring P884 Ring, Retaining...
-
Page 12: Exploded View
TM-G84-LS Rev: G DCR# 15-0407 DATE: 4/30/15 Federal Identification Code: 11815 © 2015 Cherry Aerospace G84-LS EXPLODED VIEW... -
Page 13: Declaration Of Conformity
TM-G84-LS Rev: G DCR# 15-0407 DATE: 4/30/15 Federal Identification Code: 11815 © 2015 Cherry Aerospace Declaration of Conformity Cherry Aerospace Located at 1224 East W arner Avenue, Santa Ana, CA 92705-0157, USA, In accordance with the provisions of M achine Directive 2006/ 42/ EC...
Need help?
Do you have a question about the G84-LS and is the answer not in the manual?
Questions and answers