Table of Contents
Advertisement
Quick Links
Paragon E & V
Large, ceiling-recessed screen designed for auditoriums and lecture halls.
Overview - Components
"V" Flexible Vinyl
Viewing Surface
Read and understand all warnings
Contents
Overview - Components .......................................................................................1
PLEASE READ - Safety Information ....................................................................2
Section 1 - Mounting Screen ...............................................................................3
Section 2 - Electrical Connections .....................................................................4
Section 3 - Operation............................................................................................4
"E" Free Hanging
Viewing Surface
Removing Shipping Brackets
(V screen only)
Please Note: Shipping brackets must
remain in place until product has
been mounted and connected to
power
(Sections 1 and 4)
Please Note: DO NOT operate
screen before removing shipping
brackets from screen case.
CAUTION
(Page 2 of this document)
.............................................................1
TOOLS REQUIRED
Pencil
Level
1. Remove
Fasteners
from
Bracket Clamps
.
3. Loosen screws
and remove the
shipping bracket.
before beginning installation.
Section 4 - Limit Adjustments .............................................................................4
Section 5 - Bottom Closure Removal/Replacement .......................................5
Section 6 - Tab-Tension Adjustment Procedure ..............................................5
Section 7 - Wiring Diagrams: Standard and Quiet Motor ...............................6
Section 8 - Dimensions ........................................................................................7
Paragon projection screen,, call your dealer or Draper, Inc.
INSTRUCTIONS
INSTALLATION & OPERATION
Power Drill
Hardware
(by Others)
2. Run the screen
DOWN to expose
the Dowel Screws
4. Retighten dowel
endcap screws.
If you have any difficulties installing or servicing your
Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385
draperinc.com | 765.987.7999 | 800.238.7999
|
FORM: ParagonEV_Inst23
© 2023 All Rights Reserved
Tape Measure
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Draper Paragon E
Summary of Contents for Draper Paragon E
- Page 1 Section 3 - Operation....................4 If you have any difficulties installing or servicing your Paragon projection screen,, call your dealer or Draper, Inc. Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385 draperinc.com | 765.987.7999 | 800.238.7999 FORM: ParagonEV_Inst23 © 2023 All Rights Reserved...
- Page 2 9. Do not wire motors in parallel without written permission from Draper, Inc. 2. Installation and calibration of the unit should only be performed by an 10. During testing or operation, carefully watch the surrounding area for any authorized, qualified, and experienced professional.
- Page 3 Regardless of mounting method used, the following points apply: 1. Screen should be lifted into position only by the end mounting brackets. Keep case level by lifting end plates simultaneously to prevent surface damage. Draper provides eyebolts to use in hoisting the screen. Using both mounting holes in the mounting brackets makes for a much more stable installation. Never attempt to lift screen along its length.
- Page 4 Requires screen operator to have a key. Section 4 - Limit Adjustments Please Note: Screen limits are factory set. Instructions below for minor adjustments only. Please check with Draper prior to resetting screen limits. ADJUSTING “FULLY UP” POSITION: CAUTION: 1.
- Page 5 END OF END OF DOWEL DOWEL Please Note: Draper’s Tab-Tensioning System is factory-set, and under normal circumstances will not require field adjustment. If wrinkles are observed, Figure 4 however, follow the adjustment procedure shown in Figure 4. PUSH & TURN PUSH &...
- Page 6 Paragon E & V page 6 of 7 Section 7 - Wiring Diagrams: Standard and Quiet Motor Please Note: Do not wire motors in parallel. 110-120V Motor and Quiet Motor 110-120V MOTOR STANDARD Single Station Control Internal Screen Wiring External LVC-IV Junction Box 2.214"...
- Page 7 Paragon E & V page 7 of 7 Section 8 - Dimensions * - Case support brackets will be evenly spaced along the case. 8" (203mm) 2" (51mm) 12" 1 " (305mm) (35mm) 13 " (337mm) 2 " 2 "...
Need help?
Do you have a question about the Paragon E and is the answer not in the manual?
Questions and answers