Table of Contents
Advertisement
Save
In the Save menu, the current settings for controls A-D, 1-6, FS1-4 and EXP1-2 can be stored to presets A1-D6. In addition, the "MIDI Con-
figuration" menu enables up to 16 MIDI messages or relay settings to be stored with each preset and sent immediately, when the preset is
recalled. That means that your entire rig can be configured immediately as you load a preset for a new set or song.
Store
•
From the top level menu, move the [Data Encoder] until "Save" appear in the display.
•
Press the [Data Encoder] and "Store" appears in the display.
•
Press the [Data Encoder] again and move it to select the preset location you want to save to (A1-D6). To exit press [Preset].
•
Press the [Data Encoder] to store the current setting to the selected location.
MIDI Configuration
In the MIDI configuration menu, up to 16 messages can be programmed for triggering when a preset is recalled. Note that you do need to
store the preset after you have created the settings you need, so they are stored with the preset that you want to trigger them.
The following options are available:
Type
MIDI CC
MIDI Note
MIDI Program & Bank
MIDI NRPN Coarse
MIDI NRPN Fine
MIDI Machine Control
Pacer Relay Outputs
Nektar DAW Control
Off
This menu works very similar to the Control Edit menu and these are the steps you need to go through to set it up:
•
From the top level menu, move the [Data Encoder] until "Save" appear in the display.
•
Press the [Data Encoder] and "Store" appears in the display.
•
Move the [Data Encoder] and select "M CFG"
•
Press the [Data Encoder] to select the menu.
•
The display now shows "1" in the display. This represents the first message of 16 that you can program. Move the [Data Encoder] to
select a different message number but if this is the first message you will be assigning, simply press the [Data Encoder] to select.
•
"Type" now appears in the display. Press the [Data Encoder] to select and then move the [Data Encoder] following to select one of the
options in the chart above.
•
Press [Data Encoder] when you have found the message type you want.
•
Use the [Data Encoder] to select and set the Data options and MIDI Channel as per the chart above.
•
To program the next message, press the [Preset] switch and select the next message number.
•
When all messages have been configured press [Preset] until you see "Store" in the display. You will need to save the preset or all
settings will be lost when you recall a different preset.
•
To exit the Save menu completely at any time, press [Preset] until you see "PACER" in the display.
14
Nektar Pacer User Guide
Display Abb.
Data 1
CC
MIDI CC (0-127)
NT
Note (0-127)
PGBNK
Program (0-127)
NRPNC
Value (0-127)
NRPNF
Value (0-127)
MMC
Device ID (0-127)
RELAY
Mode (nO/nC/Lt)*
DAW
Function (Solo, mute
etc)
OFF
n/a
Data 2
Data 3
Value (0-127)
n/a
Velocity (0-127)
n/a
Bank LSB (0-127)
Bank MSB (0-127)
LSB (0-127)
MSB (0-127)
LSB (0-127)
MSB (0-127)
Command (0-127)
n/a
Select (1-4)
n/a
n/a
n/a
n/a
n/a
MIDI Channel
0=Global, 1-16
0=Global, 1-16
0=Global, 1-16
0=Global, 1-16
0=Global, 1-16
n/a
n/a
n/a
n/a
www.nektartech.com
Advertisement
Table of Contents
