Advertisement
Quick Links
Advertisement
Related Manuals for HWAM 3740
Summary of Contents for HWAM 3740
- Page 1 User Manual 3740 3760 01.08.2022 / 97-9703 www.hwam.com AUTOPILOT...
-
Page 2: Table Of Contents
Table of contents Drawings ........... 3-7 Installation . -
Page 3: Drawings
Tel. (+45) 86 92 18 33 27-04-2020 nis Frigivet Format: Fax (+45) 86 92 22 18 1:10 Item numbe Scale: Created by: Item: HWAM 3740 manual 21-04-2020 Thickness: Created date: DS/EN 22768-m Drawing nu Weight: Tolerance: Configuration name: CAD-0 Material:... - Page 4 Page 4 of 20 pages...
- Page 5 Page 5 of 20 pages...
- Page 6 Page 6 of 20 pages...
- Page 7 Page 7 of 20 pages...
- Page 8 Page 8 of 20 pages...
-
Page 9: Installation
HWAM woodburning stove and confident that it will give you much pleasure. To ensure optimum operation and safety, we recommend that the installation should be carried out by an authorised HWAM retailer or a fitter recommended by the retailer. For an overview of HWAM retailers, visit www.hwam.com under “Retailer locations”. - Page 10 Ask your HWAM retailer for further information. Changing the smoke outlet from top outlet to back outlet - HWAM 3740 (drawing I) If a wood-burning stove from the factory is supplied with a top outlet but you want to change it to a back outlet, this can be done by following the instructions below.
- Page 11 12. Installing the external heat shield (1). Replace the heat shield (1) at the back of the stove. Changing the smoke outlet from top outlet to back outlet - HWAM 3760 (drawing J) If a wood-burning stove from the factory is supplied with a top outlet but you want to change it to a back outlet, this can be done by following the instructions below.
- Page 12 • Built-in pipe sleeve (12). Fits smoke flue. • Wall rosette (13). Covers disruption to wall around pipe sleeve. • Joint (14). Sealed with packing material. • Smoke outlets (15) of the HWAM stove. • Smoke flue regulating damper (16). • Soot door (17).
- Page 13 • Removable external heat shield (2b). This must always be mounted if the stove is placed next to a combustible wall. • Removable internal heat shield (2c). This must always be mounted if the stove is placed next to a combustible wall. •...
-
Page 14: Firing Manual - Wood
Firing manual - wood Your first heating session The lacquer will be fully hardened after the stove has been used, and the door and the ashpan should be opened very carefully as there will otherwise be a risk that the gaskets will stick to the lacquer. - Page 15 The stove can then be stoked again. Important! The ash pit must not be opened when lighting up. It must always be closed when the stove is in use. Otherwise the HWAM ® Autopilot™ does not function. The door should only be opened when lighting up, when restoking, and when cleaning the stove.
-
Page 16: Firing In General
Firing in general Rapid or fierce heat Rapid or fierce heat is obtained by burning many small pieces of wood. Maximum amounts of fuel: The maximum allowed amount of fuel per hour is: Wood: 1.46 kg If these limits are exceeded, the stove will no longer be covered by the factory guarantee, and it may also become damaged due to excessive heat, the glass may turn white, for example. -
Page 17: Maintenance
All service checks must be performed by an authorised fitter. Use only original spare parts. Inside cleaning Before chimney sweeping can be performed, the air control knob must be set to its minimum position to prevent soot and ash from entering the HWAM ® Autopilot™. Unless the safety fittings for transportation have not already been removed, twist the safety fittings for transportation off the two hooks by using pliers or a screwdriver. -
Page 18: Operational Problems
HWAM ® Autopilot™ (Drawing G) Lift off the rear panel. On a cold stove, the starting point of the feeler is controlled. The starting point on a cold stove is about 30 above horizontal. It should feel easy going and bouncy when you push it, no matter if the stove is cold or hot. By rising or falling temperatures it must not move at a bound. -
Page 19: Product Information Ecodesign
• Dispose of the items correctly i.e. separate the parts to be disposed of in material groups • Always dispose of items in a way that is as sustainable as possible and that is in line with the current environmental protection, reprocessing/recycling and disposal technology HWAM A/S • Nydamsvej 53 • DK-8362 Hørning... - Page 20 www.hwam.com...
Need help?
Do you have a question about the 3740 and is the answer not in the manual?
Questions and answers