Midea MKG Series Technical & Service Manual page 36

Note:
1. When replacing batteries, do not use old batteries or a differe nt type battery. This may cause the remote controller to malfunction.
2. If you do not use the remote controller for several weeks remove the batteries. Otherwise battery leakage may damage the remote controller.
3. The average battery life under normal use is about 6 months.
4. Replace the batteries when there is no answering beep from the indoor unit or if the Transmission Indicator light fails to appear.
2 Automatic Operation
When the Air Conditioner is ready for use, switch on the power and the OPERATION indicator lamp on the display
panel of the indoor unit starts flashing.
1) Use the MODE select button to select AUTO.
2) Push the TEMP button to set the desired room temperature. The most comfortable temperature settings are
between 21℃ to 28℃.
3) Push the ON/OFF button to start the air conditioner. The OPERATION lamp on the display panel of the indoor unit
lights. The operating mode of AUTO FAN SPEED is automatically set and there are no indicators shown on the
display panel of the remote controller.
4) Push the ON/OFF button again to stop the unit.
Notes:
1. In the AUTO mode, the air conditioner can logically choose the mode of COOL, FAN, HEAT and DRY by sensing the difference between the actual ambient
room temperature and the set temperature on the remote controller.
2. If the AUTO mode is not comfortable for you, the desired mode can be selected manually.
3 COOL, HEAT, and FAN ONLY Operation
1) If the AUTO mode is not comfortable, you may manually override the settings by using COOL, DRY, HEAT(HEAT
PUMP units only), or FAN ONLY modes.
2) Push the TEMP button to set the desired room temperature. When in COOLING mode, the most comfortable
settings are 21℃ or above. When in HEATING mode, the most comfortable settings are 28℃ or below.
3) Push the FAN SPEED to select the FAN mode of AUTO, HIGH, MED or LOW.
4) Push the ON/OFF button. The operation lamp lights and the air conditioner starts to run according to your settings.
5) Push the ON/OFF button again to stop.
Note: The FAN ONLY mode cannot be used to control the temperature. While in this mode, only steps 1, 3 and 4 may be performed.
4 Dry Operation
1) Push the MODE button to select DRY.
2) Push the TEMP button to set the desired temperature from 21℃ to 28℃.
3) Push the ON/OFF button. The operation lamp lights and the air conditioner starts to run in the DRY mode.
4) Push the ON/OFF button again to stop the unit.
Note: Due to the difference of the set temperature of the unit and the actual indoor temperature, the Air Conditioner when in DRY mode will
automatically operate many times without running the COOL and FAN mode.
5 Time Operation
PUSH TIMER button to set the on and off times of the unit.
6 To set the STARTING time.
1) Please push the CANCEL button to cancel any former settings.
2) Push the TIMER button. The remote controller will show the TIMER and the signal "h" is shown on the display
panel. The control is now ready to reset the TIMER ON to start the operation.
3) Push the TEMP button ( or
4) After setting the TIMER there will be a one-half second delay before the remote controller transmits the signal to
the Air Conditioner. Then, after approximately another 2 seconds, the set temperature will re-appear on the digital
display.
7 To set the STOPPING time.
1) Please press the CANCEL button to cancel any former settings.
2) Push the TIMER button and the remote controller will show the last set time for the START operation and the
signal "h" will be shown on the display panel. You are now ready to re-adjust the TIMER OFF to stop the operation.
3) Push the TEMP button to cancel the TIMER ON setting. The digital area will show "00".
AC Fan Coil Unit Two-pipe Wall-mounted Series
) to set desired unit START time .
- 35 -