Related Manuals for Protherm Ray 6 KE /14 EU
Summary of Contents for Protherm Ray 6 KE /14 EU
- Page 1 Operating instruc- tions 6 KE /14 EU 9 KE /14 EU 12 KE /14 EU 14 KE /14 EU 18 KE /14 EU 21 KE /14 EU 24 KE /14 EU 28 KE /14 EU...
-
Page 2: Table Of Contents
Contents Contents Safety ..............3 Action-related warnings ......... 3 Intended use ............3 General safety information ........3 Notes on the documentation ......5 Observing other applicable documents ....5 Storing documents..........5 Validity of the instructions ........5 Product description..........5 Product design............ -
Page 3: Safety
Safety 1 this document, shall be considered improper Safety use. Any direct commercial or industrial use Action-related warnings is also deemed to be improper. Classification of action-related warnings Caution. The action-related warnings are classified in Improper use of any kind is prohibited. accordance with the severity of the possible danger using the following warning signs and General safety information... - Page 4 1 Safety 1.3.4 Risk of injury and material damage due to maintenance and repairs carried out incorrectly or not carried out at all ▶ Never attempt to carry out maintenance work or repairs on your product yourself. ▶ Faults and damage should be immediately rectified by a competent person.
-
Page 5: Notes On The Documentation 2
Notes on the documentation 2 Notes on the documentation Display and control elements Observing other applicable documents ▶ You must observe all operating instructions enclosed with the system components. Storing documents ▶ Keep this manual and all other applicable documents safe for future use. -
Page 6: Information On The Data Plate
4 Operation Information on the data plate Cabinet-type casing The data plate is located inside on the base of the casing. Enclosing the product in cabinet-type casing requires compli- ance with the applicable design instructions. Information on the Meaning If you require cabinet-type casing for your product, consult data plate a heating specialist company. -
Page 7: Setting The Heating Flow Temperature
Operation 4 Setting the heating flow temperature Flow temperature The target room temperature is the temperature that should Press the ) button. be reached by the heating in the "Heating" operating mode ◁ The set heating flow temperature flashes in the or during the time period. -
Page 8: Guaranteeing The Correct Filling Pressure Of The Heating Installation
5 Troubleshooting 4.11 Guaranteeing the correct filling pressure of 4.12 Calling up status codes the heating installation Press and hold ( ) and ( ) at the same time for 4.11.1 Checking the filling pressure of the heating three seconds. ◁... -
Page 9: Caring For The Product
10.1 Guarantee The domestic hot water temperature in the domestic hot wa- Validity: Lithuania, Protherm ter cylinder is permanently approx. 15 °C if no domestic hot water demand is present. If the temperature in the domestic Informacijos apie gamintojo garantiją gausite galiniame pus- hot water cylinder falls to below 3 °C, the domestic hot water... -
Page 10: Appendix
Appendix Appendix Detecting and eliminating faults Problem Possible cause Solution Building power supply is switched off. Switch on the on-site power supply. Product is not connected to the power grid or is Ensure that the product has been connected to No hot water switched off via an optional control. - Page 12 Publisher/manufacturer Protherm Production s.r.o. Jurkovičova 45 ‒ Skalica ‒ 90901 Tel. 034 6966101 ‒ Fax 034 6966111 Zákaznícka linka 034 6966166 0020264738_01 www.protherm.sk 0020264738_01 ‒ 11.03.2019 Supplier Vaillant Group International GmbH Berghauser Strasse 40 ‒ 42859 Remscheid Tel. +492191 18 0 www.protherm.eu © These instructions, or parts thereof, are protected by copyright and may be reproduced or distributed only with the manufacturer's written consent.
Need help?
Do you have a question about the Ray 6 KE /14 EU and is the answer not in the manual?
Questions and answers