Table of Contents
Advertisement
Quick Links
Printed Matter No. 9839 1678 01
Publication Date 2020-03-06
Valid from Serial No. C1460001
Valid to Serial No. C2439999
ETV ST101-270-20
(65-270 Nm)
Read all safety warnings and instructions
Failure to follow the safety warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference
ETV ST101-270-20
8433208123
WARNING
Electric angle nutrunner
Product Instructions
Advertisement
Table of Contents
Related Manuals for Atlas Copco ETV ST101-270-20
Summary of Contents for Atlas Copco ETV ST101-270-20
- Page 1 ETV ST101-270-20 Printed Matter No. 9839 1678 01 Electric angle nutrunner Publication Date 2020-03-06 Valid from Serial No. C1460001 Product Instructions Valid to Serial No. C2439999 ETV ST101-270-20 8433208123 (65-270 Nm) WARNING Read all safety warnings and instructions Failure to follow the safety warnings and instructions may result in electric shock, fire and/or serious injury.
-
Page 2: Table Of Contents
Service ........................ 12 Preventing ESD problems ................ 12 Maintenance instructions ................ 12 Overhaul .................... 12 Service recommendations .............. 12 Service instructions ................ 12 Lubrication instructions ................... 13 Lubricating guide ................. 13 Lubrication ................... 13 Repair instructions .................. 13 Repair .................... 13 Troubleshooting.................... 14 © Atlas Copco Industrial Technique AB - 9839 1678 01... - Page 3 Power Focus 3000/4000................. 14 Power Focus 600/6000................... 14 If the tool becomes very hot................ 14 Recycling ....................... 15 Recycling instruction.................. 15 Recycling information .................. 15 © Atlas Copco Industrial Technique AB - 9839 1678 01...
-
Page 4: Product Information
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION CAUTION, used with the safety alert symbol, indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. © Atlas Copco Industrial Technique AB - 9839 1678 01... -
Page 5: Warranty
■ Damage to parts that occurs as a result of inadequate maintenance or performed by parties other than Atlas Copco or their Certified Service Partners during the warranty period is not covered by the warranty. ■ To avoid damage or destruction of tool parts, service the tool according to the recommended mainte- nance schedules and follow the correct instructions. -
Page 6: Country Of Origin
(>30mA) and if leakage occurs, the drive is switched off (30ms). Changing, interfering or tampering with the protection system voids all warranty and obligations from Atlas Copco. Trouble-shoot- ing and re-start of the system may only be carried out by an authorized person. Check the function of the EFP on a regular basis by pressing the trip-button. - Page 7 ETV ST101-270-20 Product information ■ Replace any defective or worn parts © Atlas Copco Industrial Technique AB - 9839 1678 01...
-
Page 8: Installation
POWER FOCUS/drive unit. Any changes made of these values in the POWER FOCUS while the tool is connected will be stored in the tool memory. © Atlas Copco Industrial Technique AB - 9839 1678 01... -
Page 9: Fitting Of The Tool Cable
To clamp the tool to a fixture, only the areas marked grey on the figure can be used. However, be careful not to damage the rubber coating when clamping the rubber handle. NOTICE The white areas in the picture must not be used for fixturing. © Atlas Copco Industrial Technique AB - 9839 1678 01... -
Page 10: Operation
The soft-start function facilitates entering the screw head and thread. The duration of the soft start is adjustable, see the manual for the drive unit. The tool is equipped with signal lights, ■ Green = OK tightening © Atlas Copco Industrial Technique AB - 9839 1678 01... - Page 11 Yellow = Warning – low torque (not for ES) ■ Red = Warning – high torque ■ Orange = Function indicator (only for SL and DL) ■ Blue = Function indicator (only for SL) © Atlas Copco Industrial Technique AB - 9839 1678 01...
-
Page 12: Service
If you decide that the electric motor is defect or in need of service, return the complete motor unit to Atlas Copco Industrial Technique for replacement. Motors which have been opened by anyone else than Atlas Copco Industrial Technique will not be ser- viced. -
Page 13: Lubrication Instructions
Repair instructions Repair Repair must only be carried out by qualified authorised personnel. For further information contact your lo- cal Atlas Copco sales representative. © Atlas Copco Industrial Technique AB - 9839 1678 01... -
Page 14: Troubleshooting
To correct, look over speed, ramp time, tightening strategy. One stage and Ergoramp are most heat conserving when applicable. Please refer to the User Guide of your POWER FOCUS. If the above correc- tions are not enough, choose a tool of the next higher capacity. © Atlas Copco Industrial Technique AB - 9839 1678 01... - Page 15 Planeraty gear Steel Cap nut Steel Planetary gear Steel Motor with transducer WEEE Steel Insulatione hose Thermoplastic urethane elastomer (TPU) Cap nut Steel Speaker WEEE Led flex card complete WEEE © Atlas Copco Industrial Technique AB - 9839 1678 01...
- Page 16 Recycling ETV ST101-270-20 Reverse ring Aluminum Electronics module WEEE Handle body Aluminum Trigger button Steel Handle PA6 GF30 Steel © Atlas Copco Industrial Technique AB - 9839 1678 01...
- Page 20 Original instructions © Copyright 2020, Atlas Copco Industrial Technique AB. All rights reserved. Any unauthorized use or copying of the contents or part thereof is prohibited. Atlas Copco Industrial This applies in particular to trademarks, model denominations, part numbers Technique AB and drawings.