Table of Contents
Advertisement
Quick Links
Oxygen Deficiency Safety Monitor
Product Description
Thank you for selecting the RAD-0002-ZR Oxygen Deficiency Safety Monitor.
This monitor is designed to protect customers and workers, anywhere bulk
Nitrogen or other inert gases are used or stored.
Today, O2 alarms are required in many local state
jurisdictions to meet fire codes. The RAD-0002-ZR
is designed specifically to meet code requirements
for O2 monitoring safety. The Remote Storage
Safety 3 Alarm constantly measures and monitors
enclosed areas for lower than normal levels of
oxygen gas.
If a gas leak occurs, visible and audible alarms will
sound on the sensor unit and on the remote display
– to warn you and your employees
The RAD-0002-ZR Oxygen Deficiency Safety Monitor is cost-effective and has many
features:
Separate SEU (Main Sensor Unit) and RDU (Remote Display Unit) allow you to see
•
warning before entering an enclosed area. Up to 3 RDUs can be used.
Large digital LCD display clearly indicates the ambient O2 concentration.
•
Relay outputs to control external devices.
•
Audible and Visual Alarm Indications at three separate alarm levels.
•
Ability to
add strobes
•
2.
NOTE: All the necessary mounting hardware
(screws, mounting brackets, power supply strip) are included.
All you will need is standard screwdriver, for basic installation.
*There are 3 additional universal power plugs included, so as the system
can be installed worldwide.
Model: RAD-0002-ZR
.
or
strobe towers
for additional indication.
Advertisement
Table of Contents
Related Manuals for CO2 Meter RAD-0002-ZR
Summary of Contents for CO2 Meter RAD-0002-ZR
- Page 1 – to warn you and your employees The RAD-0002-ZR Oxygen Deficiency Safety Monitor is cost-effective and has many features: Separate SEU (Main Sensor Unit) and RDU (Remote Display Unit) allow you to see •...
- Page 2 2. To install the SEU (Sensor Unit) start by making a mark about 12 inches off the floor or at eye level depending on the application. Please ask CO2 Meter specialist for clarification. 3. Screw the mounting bracket into the wall where you placed your mark.
- Page 3 Perform a Test 1. To test if the monitor is operating correctly, you can do a simple test. Normal Indoor O2 Levels is about 21%. 2. To test the device, simply apply pure Nitrogen on the hole located on the top right corner of the SEU.
- Page 4 SEU unit - up to a maximum of 300 ft. • Power + 24 VDC MAX– The RAD-0002-ZR is powered from 12 to 24 Volts DC. You may use the supplied 12 Volt DC Power Adapter or other 12 to 24 Volt DC Power Source.
- Page 5 • Relay 3 – is activated power loss of the SEU only. • Alarm 3 – 12% • The Peak current for all relays is 2A@30 VDC or 250 VAC. • All relays are Single Pole Double Throw with a Common (COM), Normally Open (NO) and Normally Closed (NC) contacts.
- Page 6 • Relay1_NO Relay 1 Normally Open Contact (Output) Alarm 2 controls Relay2. • Relay2_NC Relay 2 Normally Closed Contact (Output) • Relay2_COM Relay 2 Common (Input) • Relay2_NO Relay 2 Normally Open Contact (Output) Alarm 3 controls Relay3. • Relay3_NC Relay 3 Normally Closed Contact (Output) •...
- Page 7 Manual before using the product. Otherwise, the protection provided by the equipment may be impaired. These warnings provide important safety information and should always be observed. Please handle the device carefully; do not subject the product to impact or shock. Otherwise, this may cause the accuracy drift. Do not place the unit near a heat source.
Need help?
Do you have a question about the RAD-0002-ZR and is the answer not in the manual?
Questions and answers