Download Print this page

Advertisement

Quick Links

Monaco Installation Guide - Surface Profiles
The Majestic Shower Company Limited
Unit 17, Flitch Industrial Estate, Chelmsford Road, Dunmow, CM6 1XJ
Thank you for purchasing this Monaco shower screen. Please study these instructions
carefully before assembly and installation.
Checking of Parts
Parts are listed at the beginning of this guide. Please check all supplied parts immediately
upon receipt and contact the Majestic Shower Company in the event of any missing or
damaged parts.
These instructions are for left and right handed units. All parts are reversible.
Handling of Parts
When handling glass, use suction glass lifters and take care to ensure that corners or edges
are not knocked. Do not place glass on hard surfaces - place cushioning material under-
neath to prevent the glass from shattering.
Unwrap all metal parts carefully to prevent damaging the plated surfaces.
Pre Installation Checks
Prior to undertaking installation, check the accuracy of the following against specifications
for the particular installation location:
- Verticality and flatness of walls. Where wall profiles are used, some lean in or lean out of
the wall relative to the floor or tray can be accommodated (+/- 9mm if 24mm profile is used,
+/- 6mm if 17mm profile is used).
- Levelness and flatness of the floor or tray. Where a profile or underframe is used under-
neath a glass panel, any minor hollows in the mounting surface must be solidly packed to
prevent deflection under the weight of the glass as this may over stress the glass.
Installation Tips
The general principle of assembly is to assemble parts in the steps shown - first a dry
assembly to check fits or mark cutting or drilling positions and then a final assembly with
silicone.
When cutting aluminium extrusion, wrap the profile with masking tape first and cut through
the taped area - this will help protect the surrounding surface. Use a fine file to smooth cut
.
edges
If anti-calcium glass has been specified, the treated side of the glass will be indicated and
should always face inwards towards the wet side of the shower area.
DO NOT ASSEMBLE WITHOUT FULLY READING THESE INSTRUCTIONS
Telephone +44 (0) 8448 001 500
Facsimile +44 (0) 1279 635 074 info@majesticshowers.com www.majesticshowers.com
1

Advertisement

loading

Summary of Contents for Majestic Monaco

  • Page 1 Checking of Parts Parts are listed at the beginning of this guide. Please check all supplied parts immediately upon receipt and contact the Majestic Shower Company in the event of any missing or damaged parts. These instructions are for left and right handed units. All parts are reversible.
  • Page 2 Monaco Installation Guide - Surface Profiles 1 x Glass Panel 2 x Wall Bracket assemblies including screws ~10 mm and gaskets Wall fixing screws and wall plugs also supplied. 2 x Surface Profile Rubber cushioning 1 x 10mm Spacer for...
  • Page 3 Monaco Installation Guide - Surface Profiles - vJUN16 Reposition the vertical wall channel and insert the top and bottom screws to hold it Place the 10mm spacer into the floor channel and use it to align the vertical wall in place. Insert the rubber strip into the floor channel. Using suction glass lifters, lift profile.
  • Page 4 Monaco Installation Guide - Surface Profiles- vJUN16 The glass panel can be moved backwards or forwards in the floor profile but the Disassemble the glass-to-wall brackets, being careful not to damage the faceplates. glass must be inside the vertical wall profile by at least 5mm along its entire height.
  • Page 5 Monaco Installation Guide - Surface Profiles- vJUN16 Put the brackets to one side and use the suction lifters to remove the glass panel. Run a bead of silicone along the back face of the wall profile and screw it tightly in Remove the floor profile, having marked its position and unscrew and remove the place.
  • Page 6 Monaco Installation Guide - Surface Profiles- vJUN16 Run a bead of silicone along the base of the floor profile and reposition it on the tray Run a bead of silicone along each inside face of each profile as shown. where marked. Use the 10 mm spacer to ensure that it is aligned with the wall profile, push the mitred ends together and tape in position.
  • Page 7 Monaco Installation Guide - Surface Profiles- vJUN16 To prevent leakage around the wall brackets, fill the glass slot at the lower bracket Using a smear of silicone, fit the chromium screw covers provided to the wall with silicone as shown. Loosely fix the face plates of the brackets through the holes bracket screws and the cover plates to the wall screw sections.