Advertisement
Quick Links
Maine Installation Guide (with underframe) - vJUN17
1
Thank you for purchasing this Maine shower door. Please study these instructions
carefully before assembly and installation.
Checking of Parts
Parts are listed at the beginning of this guide. Please check all supplied parts immediately
and contact the Majestic Shower Company in the event of any missing or damaged parts.
These instructions are for left and right handed units. All parts are reversible.
Handling of Parts
When handling glass, use suction glass lifters and take care to ensure that corners or edges
are not knocked. Do not place glass on hard surfaces - place cushioning material under-
neath to prevent the glass from shattering.
Unwrap all metal parts carefully to prevent damaging the plated surfaces.
Pre Installation Checks
Prior to undertaking installation, check the accuracy of the following against specifications
for the particular installation location:
- Verticality and flatness of walls. Walls must be substantially vertical and the finished wall
to finished wall dimension must be as specified at the top and bottom of the door.
- Levelness and flatness of the floor or tray.
Installation Tips
The general principle of assembly is to assemble parts in the steps shown - first a dry
assembly to check fits or mark cutting or drilling positions and then a final assembly with
silicone.
If anti-calcium glass has been specified, the treated side of the glass will be indicated and
should always face inwards towards the wet side of the shower area.
DO NOT ASSEMBLE WITHOUT FULLY READING THESE INSTRUCTIONS
The Majestic Shower Company Limited
Telephone +44 (0) 8448 001 500
17 Flitch Industrial Estate, Chelmsford Road, Dunmow, CM6 1XJ
Facsimile +44 (0) 1279 635 074 info@majesticshowers.com www.majesticshowers.com
Advertisement
Related Manuals for Majestic vJUN17
Summary of Contents for Majestic vJUN17
- Page 1 Parts are listed at the beginning of this guide. Please check all supplied parts immediately and contact the Majestic Shower Company in the event of any missing or damaged parts. These instructions are for left and right handed units. All parts are reversible.
- Page 2 Maine Installation Guide (with underframe) - vJUN17 2 x Glass to Wall Hinge assemblies with 1 x Underframe rubber packing strips ~10 mm Tray 1 x Finger Pull Handle (pre installed) OR 1 x Glass Door 1 x Door Handle or Towel Rail Assembly...
- Page 3 Maine Installation Guide (with underframe) - vJUN17 DOOR WALL DOOR Rubber packing strips Rubber strips Hinge with face plate removed for illustration purposes only. 8 mm gap between glass and wall Run a substantial bead of silicone along the centre of the underside of the...
- Page 4 Maine Installation Guide (with underframe) - vJUN17 Position the hinges centrally in their slots and use a set square to align them with Steps 5-7 require one person to support the glass door at all times, while the other the edge of the glass. Check that the holes are adequately packed with the rubber person mut be inside the enclosure with hinge faceplates, gaskets and screws.
- Page 5 Maine Installation Guide (with underframe) - vJUN17 Drill 7 mm holes in the wall where marked and insert wall plugs. Replace the door. Use a long spirit level to check that the door is plumb vertical and then mark the screw holes for the hinges and remove the door.
- Page 6 Maine Installation Guide (with underframe) - vJUN17 Notch Slit 10 mm 20 mm 12.5mm Remove sharp corners Slit bubble here End to touch top of underframe Fit one length of the vertical seal full height on the handle side of the door and trim The other length of vertical seal is to be cut in 3 sections to fit to the door above, it level with the top edge of the glass.
- Page 7 Maine Installation Guide (with underframe) - vJUN17 Slit Notch Cut the horizontal seal to the width of the door for fitting to the bottom edge of the door with the deflector blade facing inwards. The horizontal seal should fit snugly VIEW FROM between the two vertical seals as shown.
- Page 8 Maine Installation Guide (with underframe) - vJUN17 OUTWARD INWARD OPENING OPENING DOOR DOOR 5-6mm Notch Push the underframe insert into the underframe channel under the door noting If you have the Finger Pull handle option, the door will be supplied with the handle the difference in orientation for outward and inward opening doors.
- Page 9 Maine Installation Guide (with underframe) - vJUN17 OUTSIDE OF SHOWER Grub screw Bias adjustment INSIDE OF screws SHOWER Plastic washer Alternatively, if you have a back-to-back handle, fit this to the door as shown, Close the door carefully and check that the seals close on to the walls correctly.
- Page 10 Maine Installation Guide (with underframe) - vJUN17 Once you are satisfied that the door is correctly adjusted and that the bolts on the hinges are tightened to 10 - 12 Nm torque, fit the cover caps provided to the screw heads using a small amount of silicone.