NetApp FAS2050 Installation And Setup

Before you begin
1
If you have not already done so, gather the required information and confirm your site
requirements, as described in the Site Requirements Guide at http://now.netapp.com/.

Install in rack

3
Note: Remove handles after the
system is supported by the shelf.
Setting the Disk Shelf IDs
Shelf ID
switch
Note: The disk shelf IDs for the
disk shelves should be set in the
range 1 to 6. Leave the FAS2050
disk shelf ID at the preset value of 00.

Cable the system

4
Cable controllers
RJ-45 to DB-9 adapter to console port (required)
1
0a 0b
Console cable to adapter
2
0a 0b
Network cables to e0a and e0b ports
3
0a 0b
Network cable to Remote Management port
4
6
0a 0b
Connect the installed PCI card, as needed.
5

Boot the system and proceed with setup

5
- Turn on the power to your system. It takes the LEDs on your system power supplies a few seconds to illuminate.
- Windows® environments with DHCP: Install System Manager from the CD-ROM and run it on a Windows client system to discover, configure, and manage your system. Connect your
Windows client system through the management LAN.
- All other configurations: Use the console interface and proceed through the setup questions. See the Data ONTAP Software Setup Guide at http://now.netapp.com/.
FAS2050 System Installation and Setup
Caution:
Only use the NetApp ® rail kit to install your system. Using a different rail kit can cause injury to you or damage to your system.
Four-post rack
Clip nut
tool
Front rail
(2x)
Clip nut (4x)
Note: Refer to the rail kit installation flyer included with the rail kit for the two-post procedure.
Cable disk shelves
These are a few common configurations. For additional options, see Supported Configurations for
FAS2000-series Systems at http://now.netapp.com.
Port labels
e0a e0b
Active/Active NAS or ISCSI:
1 Fibre Channel Disk Shelf Stack (Multipath)
Controller to shelf
1
8
Remote
Management
Port
Fibre
Channel
e0a e0b
8
Ethernet
Console Shelf to shelf
2
e0a e0b
8
Shelf to controller
3
e0a e0b
8
8

Unpack and verify contents

2
Your system comes with an accessory kit that includes the following components:
- This installation poster
- Software license flyer
- System Manager CD-ROM
- Grounding kit
(2x)
(2x)
Active/Active SAN: 4 FCP
Connections 1 Fibre Channel Disk Shelf Stack (Multipath)
Controller to switches
1
FAS2050
1b 1a
a 0 0b 10101 e a 0 e0b
P S U P S U
CM-B
1b 1a
a 0 0b e a 0 e b 0
10101
P S U
or
DS14
OUT IN
P S U P S U
P S U
IN OUT
DS14
OUT IN
P S U P S U
P S U
IN OUT
Controller to shelves
2
FAS2050
1b 1a
a 0 0b 10101 e a 0 e0b
P S U P S U
CM-B
1b 1a
a 0 0b 10101 e a 0 e b 0
P S U
DS14
OUT IN
P S U P S U
P S U
IN OUT
DS14
OUT IN
P S U P S U
P S U
IN OUT
Shelf to controller
3
FAS2050
1b 1a
a 0 0b 10101 e a 0 e0b
P S U P S U
CM-B
1b 1a
a 0 0b 10101 e a 0 e b 0
P S U
DS14
OUT IN
P S U P S U
IN OUT
P S U
DS14
OUT IN
P S U P S U
P S U
IN OUT
- Power cables
- DB-9 to RJ-45 console adapters
- Rail kit (for two-post and four-post racks)
(4x)
4U
3U
3U
FAS2050
1b 1a
a 0 0b 10101 e a 0 e0b
P S U
CM-B
1b 1a
a 0 0b 10101 e a 0 e b 0
DS14
OUT IN
P S U
IN OUT
DS14
OUT IN
P S U
IN OUT
FAS2050
1b 1a
a 0 0b 10101 e a 0 e0b
P S U
CM-B
1b 1a
a 0 0b 10101 e a 0 e b 0
DS14
OUT IN
P S U
IN OUT
DS14
OUT IN
P S U
IN OUT
FAS2050
1b 1a
a 0 0b 10101 e a 0 e0b
P S U
CM-B
1b 1a
a 0 0b 10101 e a 0 e b 0
DS14
OUT IN
P S U
IN OUT
DS14
OUT IN
P S U
IN OUT
Copyright © 2009 NetApp, Inc. All rights reserved.

Connect power

Note:
You do not need to
ground your system.
210-03951+C0