Advertisement
Quick Links
PRELIMINARY
Parlé
Video Display Mount Kit (PMA 2000-DM)
Installation Guide
ABOUT THIS KIT
The PMA 2000-DM kit mounts a Parlé 2000 series bar to an (X- or H-type)
VESA-mounted video display.
INSTALLATION CONSIDERATIONS
• This kit can be configured so the Parle bar is above or below the display.
In most cases, this can be done without removing the display from the
VESA mount.
• Spring tension arms hold the bar against the video display. The brackets
and arms may be reconfigured depending on the size of the display, the
type of VESA mount, and the bar's position.
• To use this kit, access to either the screws holding the VESA (X- or
H-type) mount to the display, or the vertical rails or U-channel on an
H-type VESA mounting system is necessary.
• Please read the initial pages of this guide to prepare for the installation,
and determine which configuration fits your appliction.
KIT CONTENTS
Left Arm
Tools needed:
• 90° ratcheting or short bit Phillips Screwdriver
A:
Included Hardware
Right Arm
Crossbar
9300 S.W. Gemini Drive Beaverton, OR 97008 USA
Qty
Description
4
M8 x 25 PH Screws
4
M8 x 30 PH Screws
4
M8 x 40 PH Screws
4
M8 x 45 PH Screws
4
Spacers
2
M6 x 12 Flat Head Screws
2
M6 Nuts
2
M8 Flat Washers
2
M5 x 8 PH Screws
CONFIGURATIONS
1) PMA Kit attached to an H-style
(or X-Style) VESA mount with the
bar below the display.
2) PMA Kit attached to an X-style
(or H-Style) VESA mount with the
bar above the display.
3) PMA Kit shown attached to an
the vertical rails of a VESA mount
with the bar under the display.
4) Use spacers to attach the PMA
kit to Low Profile VESA mounts.
Will work with either H-style (or
X-style) VESA mount and allow the
bar to be mounted either above or
below the display.
Note: Must be able to remove display
from the mount to install the spacers.
W:
www.biamp.com
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Biamp Parle 2000 Series
Summary of Contents for Biamp Parle 2000 Series
- Page 1 Tools needed: Note: Must be able to remove display • 90° ratcheting or short bit Phillips Screwdriver from the mount to install the spacers. 9300 S.W. Gemini Drive Beaverton, OR 97008 USA www.biamp.com...
- Page 2 PMA 2000-DM KIT ELEMENTS Bracket Spring Arm Spring Mechanism The pin keeps arm extended Traveler Arm during installation of the bar in an under-display configuration. Crossbar PREPARATION Remove Table Stand Remove the bar from either the table stand (1) or the wall plate (2) before attaching to the PMA kit.
- Page 3 INSTALLATION CHOICES This guide covers several possible configuration options for installing the bar on your video display (TV). You must be able to access the circled points for that option. Make a choice below that matches your intended configuration. Each choice includes a link to take you to the set of instructions to accomplish that configuration.
- Page 4 CONFIGURATION 1 (Bar below the TV using the TV/VESA attachment) Hold one Spring Arm behind the TV with the bracket level with the VESA attachment to the TV, answer the following question, and take appropriate action. 1. Will the arm work with the notched bracket in the upper position? (Attach arms to TV) or (Change bracket position) Note: The Spring Arm should extend almost to, but not past the edge of...
- Page 5 CONFIGURATION 1 (continued - Bar below the TV using the TV/VESA attachment) Attach arms at the lower TV/VESA mounting points Kit parts (H- or X-type VESA mounts) Configured arms x2 Determine where the TV is attached to the VESA mount. If feasible, pull display Optional hardware away from the wall for easier access to the mounting screws.
- Page 6 CONFIGURATION 1 (continued - Bar below the TV using the TV/VESA attachment) Crossbar Attachment Kit parts Crossbar x1 1. The arms should hang parallel. (M5 Screws) x2 2. Fit the crossbar into the small notches in the Traveler Arms (as shown). Center and loosely screw the crossbar to each arm.
- Page 7 CONFIGURATION 1 (continued - Bar below the TV using the TV/VESA attachment) Bar Attachment to PMA 2000-DM Hardware M3 Screws x2 Adjust the PMA crossbar position to easily allow the bar to be From Parlé bar stand attached. The bar will hang on the knobs in the center of the or plate removal crossbar.
- Page 8 CONFIGURATION 2 (Bar above the TV using the TV/VESA attachment) Change arm configuration To preserve the tension spring action function, the lower portion of each arm The arms ship configured for (Traveler Arm) must be removed and reattached to the opposite Spring Arm. below-the-screen mounting.
- Page 9 CONFIGURATION 2 (continued - Bar above the TV using the TV/VESA attachment) Hold one Spring Arm behind the TV with the bracket level with the VESA attachment to the TV, answer the following question, and take appropriate action. 1. Will the arm work with the notched bracket in the upper position? (Attach arms to TV) or (Change bracket position)
- Page 10 CONFIGURATION 2 (continued - Bar above the TV using the TV/VESA attachment) Attach arms at the upper TV/VESA mounting points Kit parts Configured arms x2 (H or X VESA mounts) Optional hardware Determine where the TV is attached to the VESA mount. If feasible, pull display away from the wall for easier access to the mounting screws.
- Page 11 CONFIGURATION 2 (continued - Bar above the TV using the TV/VESA attachment) Crossbar Attachment Kit parts Crossbar x1 The method of attaching the crossbar to the arms is the same (M5 Screws) x2 irrespective of the type of VESA mount - images show the X-type mount.
- Page 12 CONFIGURATION 2 (continued - Bar above the TV using the TV/VESA attachment) Bar Attachment to PMA 2000-DM Hardware M3 Screws x2 Adjust the PMA crossbar to easily allow the bar to be attached. The From Parlé bar table bar will hang on the knobs in the center of the crossbar. For above- stand or wall plate display configurations, the crossbar should be at least 102 mm (4") removal...
- Page 13 CONFIGURATION 3 (Bar below the TV - Kit connection to VESA vertical rails) (H-TYPE VESA MOUNT) Arm Attachment to VESA Vertical Rails Attachment to the vertical rails is indicated either for ease of installation access, or when the VESA-display attachment points are too far away from the edge of the display for the Traveler Arms to extend past the edge.
- Page 14 CONFIGURATION 3 (continued - Bar below the TV / Kit connection to vertical rails Arm Attachment to VESA Vertical Rails Attachment to the vertical rails is indicated either for ease of installation access, or when the VESA-display attachment points are too far away from the edge of the display for the Traveler Arms to extend past the edge.
- Page 15 CONFIGURATION 3 (continued - Bar below the TV / Kit connection to vertical rails Crossbar Attachment Kit parts Crossbar x1 The method of attaching the arms to the mounting points is the (M5 Screws) x2 same irrespective of the position - above or below the display. Most of the images show connections in the below-display configuration.
- Page 16 CONFIGURATION 3 (continued - Bar below the TV / Kit connection to vertical rails Bar Attachment to PMA 2000-DM Hardware M3 Screws x2 Adjust the PMA crossbar to easily allow the bar to be attached. From Parlé bar stand The bar will hang on the knobs in the center of the crossbar. or plate removal For above-display configurations, the crossbar must be at least 76 mm (3") below the edge of the display.
- Page 17 CONFIGURATION 4 (Bar below the TV / Low Profile VESA mount) Low Profile VESA mounts (Add spacers) Parts and Hardware Spacers x4 If there isn't enough space to insert the arms between the TV and VESA mount, M8 x 40 Screws x4 OR you should install spacers at each of the 4 attachment points.
- Page 18 PRELIMINARY CONTACT US Email: support@biamp.com Warranty: biamp.com/legal/warranty-information Web: support.biamp.com Safety & Compliance: biamp.com/compliance 9300 S.W. Gemini Drive Beaverton, OR 97008 USA www.biamp.com 27APR2023...
Need help?
Do you have a question about the Parle 2000 Series and is the answer not in the manual?
Questions and answers