Page 1
“<Control No.: C****>” used in these documents should be used to search for information on our support website (https://i-pro.com/global/en/surveillance/training_support/support/technical_ information) and will guide you to the right information. • microSDXC/ microSDHC/ microSD memory card is described as microSD memory card.
Contents Limitation of liability ........................3 Disclaimer of warranty ........................3 About notations ..........................4 System requirements for a PC ...................... 4 Network security ........................... 5 Precautions for use ........................6 Parts and functions ........................9 Insert / remove a microSD memory card ..................14 Troubleshooting ...........................
IMPROVEMENTS OF THIS PUBLICATION AND/OR THE CORRESPONDING PRODUCT (S). Disclaimer of warranty IN NO EVENT SHALL i-PRO Co., Ltd. BE LIABLE TO ANY PARTY OR ANY PERSON, EXCEPT FOR REPLACEMENT OR REASONABLE MAINTENANCE OF THE PRODUCT, FOR THE CASES, INCLUDING BUT NOT LIMITED TO BELOW:...
S2536LT The functions with this notation are available when using the WV-S2536LTN series. S2536LN The functions with this notation are available when using the WV-S2536LN series. The functions with this notation are available when using the WV-S2536L series. S2536L The functions with this notation are available when using the model with the clear dome cover.
Network security As you will use this unit connected to a network, your attention is called to the following security risks. A Leakage or theft of information through this unit B Use of this unit for illegal operations by persons with malicious intent C Interference with or stoppage of this unit by persons with malicious intent It is your responsibility to take precautions such as those described below to protect yourself against the above network security risks.
Precautions for use When the product is accessible from the Periodically images on the screen appear to Internet be distorted To prevent unauthorized access, note the following. When the camera is installed in a location where it is subject to small vibrations (for example, when •...
Page 7
We shall not be liable for content • If dirt cannot be wiped off with a damp cloth, compensation, losses of recorded or use a neutral detergent for kitchen utensils, edited content and any direct or indirect and sufficiently rinse off the detergent. consequent damages caused by failure to When using a detergent containing wax record or edit due to faults with this unit or...
Page 8
AVC Patent Portfolio License THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE PERSONAL USE OF A CONSUMER OR OTHER USES IN WHICH IT DOES NOT RECEIVE REMUNERATION TO (i) ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD (“AVC VIDEO”) AND/OR (ii) DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL ACTIVITY AND/...
Parts and functions The following are descriptions when using the model WV-S2536LN. Cables [1] Ethernet cable (category 5e or better, straight, 4 pairs (8 pins)) [5] 4P alarm cable (WV-QCA501A accessory) [5] EXT I/O cable 2P power cable I/O Cable...
Page 10
[2] Power supply cable / 2P power cable (WV-QCA501A accessory) Connect the output cable of the DC power supply to the 2P power cable. IMPORTANT: • Be sure to use the 2P power cable provided with WV-QCA501A. • Be sure to fully insert the 2P power cable into the power supply cable. Otherwise, it may damage the camera or cause malfunction.
Page 11
[5] EXT I/O cable / 4P alarm cable (WV-QCA501A accessory) Note: • Off, input, and output of the ALARM IN2 and 3 can be switched by configuring the setting. Refer to the Operating Instructions for further information about the ALARM IN2 and 3 settings (“Off”, “Alarm input”, “Alarm output”...
Page 12
Indicators and buttons INITIAL SET button SD memory card SD ON/OFF button warning/error indicator LINK indicator ACT indicator WIDE button SD (MOUNT) indicator TELE button INITIAL SET button (Initializing / NTSC PAL switch button) Follow the steps below to initialize the network camera. Turn off the power of the camera.
Page 13
SD (MOUNT) indicator Lights off → Blinks green → Lights off • When a microSD memory card is inserted and could be recognized Lights off → Lights green • When data can be saved after the microSD memory card is inserted and the SD ON/OFF button is pressed (less than 1 second) •...
Insert / remove a microSD memory card Note: • Refer to the Operating Instructions on our manual website for further information about the microSD memory card settings. • Refer to our support website <Control No.: C0107> for latest information about the compatible microSD memory cards.
Page 15
Remove a microSD memory card When removing a microSD memory card, reverse the procedure. • To remove the microSD memory card, hold down the SD ON/OFF button for about 2 seconds. When the flashing SD (MOUNT) indicator goes out, you can remove the microSD memory card. IMPORTANT: •...
Troubleshooting Before asking for repairs, check the symptoms with the following table. Contact your dealer if a problem cannot be solved even after checking and trying the solution in the table or a problem is not described below. Reference Symptom Cause/solution pages When using a PoE device for power supply...
Page 17
Reference Symptom Cause/solution pages • Check the following. • Grounding of the camera, a switching hub or peripheral devices are not done. • The camera is used near an electrical power line. • The camera is used near a device which produces Audio input contains Installation strong magnetic field or radio waves (such as near a...
(excluding an attachment for the conduit portion) Approx. 1.1 kg {2.43 lbs.} Mass: (excluding an attachment for the conduit portion) Finish: Main body: Aluminum die cast, i-PRO white Outer fixing screws: Stainless steel (Corrosion-resistant treatment) Dome cover: PC resin, S2536LT S2536LN...
Page 19
Others: Tamper-resistant enclosure *1 Refer to our support website <Control No.: C0106> for further information about Power source and Power consumption information. *2 When using with the IR LED Light constantly lit, the upper limit of the operating temperature range is +50 °C {+122 °F}.
Page 20
0.017 lx {0.0016 footcandle} (50IRE, F1.3, Maximum shutter: Off (1/30 s), AGC: 11) 0.0011 lx {0.0001 footcandle} (50IRE, F1.3, Maximum shutter: max. 16/30 s, AGC: 11)* * Converted value Intelligent Auto: On/ Off Super Dynamic * On/ Off The level can be set in the range of 0 to 31. Dynamic range: Max.
Page 21
IR LED Light: High/ Middle/ Low/ Off Maximum irradiation distance: 70 m {Approx. 230 ft} (30IRE)* 50 m {Approx. 164 ft} (50IRE) Maximum irradiation distance: 50 m {Approx. 164 ft} (30IRE)* 35 m {Approx. 116 ft} (50IRE) * Converted value White balance: ATW1/ ATW2/ AWC Digital noise reduction:...
Page 22
Focus range: S2536LT 2 m {78-3/4 inches} – ∞ S2536LN S2536L 0.3 m {11-13/16 inches} – ∞ Aperture range: S2536LT F1.7 – T405 S2536LN S2536L F1.3 – Close Angular field of view: S2536LT [16:9 mode] Horizontal: 15° (TELE) – 36° (WIDE) Vertical: 9°...
Page 25
Browser * Microsoft Edge Firefox Google Chrome Maximum concurrent 14* (Number of sessions that can connect to cameras at the same time) access number: * Depends on network conditions Multi-screen: Up to 16 camera images can be displayed simultaneously on a multi- screen.