Panasonic AW-RP605 Operating Instructions Manual page 24

Operation
When component signals are used
1. Select the pan-tilt
CONTROL/PREVIEW MONITOR OUT SEL button.
2. Connect a waveform monitor to the VIDEO/Y OUT
connector on the main unit corresponding to the pan-tilt
head system currently selected.
3. Press the MODE button to establish the BAR mode and
switch the output signals from the convertible camera to
color bar signals.
4. Press the MENU button, turn the menu setting control
(main), and set it so that the CABLE COMP item
appears at the top of the LCD panel.
C C A A B B L L E E C C O O M M P P
5. Press the OK button.
The following item appears on the LCD panel.
C C A A B B L L E E C C O O M M P P A A U U T T O O
S S T T A A R R T T ? ? n
6. Turn the menu setting control (main), and set it so that
the following item appears on the LCD panel.
C C A A B B L L E E C C O O M M P P M M A A N N U U A A L L
Y Y L L e e v v e e l l : :
<Note>
When composite signals have been set as the video
output signals, the video output signals will be switched
to component signals.
When another item on the menu is selected, the output
signals will be switched to the composite signals.
7. Adjust the luminance signal using the menu setting
control (R) in such a way that the level of the white area
appearing on the waveform monitor is set to 100 IRE
(0.714V).
IRE
+100
100
90
80
70
60
50
40
30
20
10
+7.5
0
–10
–20
–30
–40
Waveform monitor
8. Connect the VIDEO/Y OUT connector on the main unit
to the external reference input connector on the
waveform monitor, and connect the Pr OUT connector
on the main unit to the video signal input connector on
the waveform monitor.
head system using
O O K K K K e e y y
n
O O K K K K e e y y
0 0
100 IRE
(0.714 V)
9. Turn the menu setting control (main), and set it so that
the following item appears on the LCD panel.
the
C C A A B B L L E E C C O O M M P P M M A A N N U U A A L L
f f R R e e s s p p o o n n s s e e : :
<Note>
When component signals have been set as the video
input signals, the output signals from the convertible
camera will be switched to Y/C signals, and
chrominance signals will be output from the Pr OUT
connector. When another item on the menu is selected,
the output signals will be switched to the component
signals.
10. Adjust the frequency response using the menu setting
control (R) in such a way that the burst level appearing
on the waveform monitor is set to 40 IRE (0.286V).
Repeatedly adjust the luminance signal and frequency
response until the signal waveforms shown below are
matched.
<Note>
In the luminance and chrominance signal adjustments
performed by the multi-function controller, the level
cannot be reduced below the level of the input signals
from the camera.
It may not be possible to perform these adjustments if
the length of the cables from the pan-tilt heads to the
main unit of the multi-function controller is too short.
IRE
100
90
80
70
60
50
40
30
+20
20
10
0
–10
–20
–20
–30
–40
11. Select the next pan-tilt head system using the
CONTROL/PREVIEW MONITOR OUT SEL button, and
continue adjusting the cable compensation in each
system concerned.
3
OPERATE IRIS ZOOM FOCUS
OPEN TELE FAR WHITE
GAIN BAL
AUTO
A
ON
MANU
MODE
BAR
B
OFF CAM
DATA SET
INCOM
ATW
CALL
TR/PSET M.LOCK
CLOSE WIDE NEAR
LEVEL
IRIS TR
PSET
TELE
MEMORY
AUTO
MANU
LOCK
EMPTY
IRIS
FOCUS
CLOSE OPEN
NEAR WIDE FAR
ZOOM/FOCUS/IRIS
LIMIT
24
0 0
+20
–20
Waveform monitor
4•6•9
5
7•10 4
CAMERA CONTROL
AWC
LAMP DEF
LCD
CONTRAST
NG
OK
START
ABC R/B POINT START/STOP
CAMERA GAIN/PED MENU OK
CONTROL
TRACING/PRESET MEMORY
1 2 3 4 5 6 7 8 9 10
PRIORITY
1
CONTROL/PREVIEW MONITOR OUT SEL
11 12 13 14 15 16 17 18 19 20
SPEED
LOW
FULL
HIGH
21 22 23 24 25 26 27 28 29 130
IRIS
FOCUS
L
31 32 33 34 35 36 37 38 39 40
41 42 43 44 45 46 47 48 49 50
CLOSE
NEAR
PAN/TILT/FOCUS/IRIS
LIMIT
ON OFF
40 IRE
(0.286 V)
1
PAN/TILT SET
WIP H/F EXT ND OPTION
TRACING MEMORY
RESTORE RESET
TALLY
2 3 4 5 AUX
UP
R
OPEN
DOWN FAR