Table of Contents
Advertisement
Effect Parameters
Dedicated Effects for USB/MOBILE/BLUETOOTH Channels
ENHANCE (EH)
ENHANCE is an effect that makes the sound more sharply defined.
It also contains COMP (COMPRESSOR) which makes the volume more
consistent, DE-ESS (DE-ESSER) which suppresses sibilance.
Parameter
Value
(Bold: default)
SW
OFF,
ON
ENHANCE
0–20–100
COMP
0–30–100
DE-ESS
0–30–100
NOISE SUPPRESSOR (NS)
This effect reduces the noise.
Parameter
Value
(Bold: default)
SW
OFF,
ON
THRESHOLD
0–30–100
RELEASE
0–30–100
This specifies the threshold input volume used for activating the
noise suppressor.
INPUT
DETECT
NS INPUT
74
Explanation
Turns this effect on/off.
Adjusts the depth of ENHANCE.
The sound becomes more sharply
defined as this value is increased.
Adjusts the depth of COMPRESSOR.
The volume becomes more consistent as
this value is increased.
Adjusts the depth of DE-ESSER.
Sibilance is suppressed more strongly as
this value is increased.
Explanation
Turns this effect on/off.
Adjust this parameter as appropriate for
the volume of the noise.
If the noise level is high, a higher setting is
appropriate.
If the noise level is low, a lower setting is
appropriate.
Adjusts the time from when the noise
suppressor begins to function until the
noise level reaches "0".
Input volume from USB port, Mobile jack,
or mobile device.
* Ordinarily, DETECT should be set to
"INPUT".
Noise suppressor input volume.
* When connected as illustrated below,
and you want to prevent a spatial-type
effects sound (such as a delay sound)
from being eradicated by the NS, you
should set DETECT to "NS INPUT".
DLY
NS
(Spatial-type effect)
FX
With FX, you can select the effect to be used from the following.
Parameter
Value
(Bold: default)
SW
OFF,
ON
Selects the effects to use for FX.
FX TYPE
Ø
"FX TYPE"
FX TYPE
Type
Explanation
DIST
Produces a distorted voice.
Distortion
RADIO
Produces a radio voice.
This effect intentionally degrades the sound to create a
LO-FI
distinctive character.
A filter modifies the brightness or thickness of the sound by
FILTER
cutting a specific frequency range.
You can produce a wah effect with the filter changing in
T.WAH
response to level.
Touch wah
RING MOD
Gives a metallic character to the sound, creating the
impression that the sound is going out of focus.
Ring modulator
In this effect, a slightly detuned sound is added to the original
CHORUS
sound to add depth and breadth.
The flanging effect gives a twisting, jet-airplane-like character
FLANGER
to the sound.
TREMOLO
Tremolo is an effect that creates a cyclic change in volume.
By adding varied-phase portions to the direct sound, the
PHASER
phaser effect gives a whooshing, swirling character to the
sound.
This consecutively interrupts the sound to create the
SLICER
impression that a rhythm backing phrase is being played.
Divides the audio input into three ranges (LO, MID, HI) and
ISOLATOR
cuts the specified region. You can cut in synchronization with
the tempo.
VIBRATO
This effect creates vibrato by slightly modulating the pitch.
PAN
Moves the stereo position (pan).
FREEZE
This produces the Freeze function to hold sounds.
Repeats a short portion of the input sound, giving it a buzzy
GRANULAR
character or producing the effect of playing a roll.
Granular delay
This effect adds delayed sound to the direct sound, giving
DELAY
more body to the sound or creating special effects.
DIST
Produces a distorted voice.
Parameter
Value
(Bold: default)
DIST
0–30–100
TONE
-50–0–+50
EFFECT LEVEL
0–50–100
DIRECT LEVEL
0–40–100
RADIO
Produces a radio voice.
Parameter
Value
(Bold: default)
LO-FI
1–7–10
LEVEL
0–50–100
Explanation
Turns this effect on/off.
Explanation
Adjusts the degree of distortion.
Adjusts the tonal character.
Adjusts the volume of the effect sound.
Adjusts the volume of the direct sound.
Explanation
Adjusts the amount of blurring.
Adjusts the volume of the effect sound.
Advertisement
Table of Contents
