Bedienungsanleitung DV-5120 VIEWEG 1.1 Das DV-5120 Mit dem Schlauchquetschventil lassen sich Dosierungen von sehr kleinen Dosier- punkten bis zur kontinuierlichen Dosierung von Raupen für nieder- bis mittelviskose Materialien durchführen. Der auswechselbarer Schlaucheinsatz ist das einzige Teil des Ventils, das Berührung mit Ihrem Material hat.
Bedienungsanleitung DV-5120 VIEWEG 2 Sicherheitshinweise 2.1 Allgemeines zur Sicherheit Wird dieses Ventil für andere Zwecke eingesetzt, als in WARNUNG dieser Bedienungsanleitung beschrieben, kann es zu Personen- oder Sachschäden kommen. Setzen Sie das Ventil nur gemäß der Anleitung ein. 2.2 Gefahren für den Bediener Vor Gebrauch die Bedienungsanleitung sorgfältig lesen.
Bedienungsanleitung DV-5120 VIEWEG 4 Inbetriebnahme 4.1 Einlegen oder wechseln des Schlaucheinsatzes Stellen Sie vor der Wartung sicher, dass das System nicht unter Druck steht! Vergewissern Sie sich, dass keine Flüssigkeit mehr im Ventil ist. Tragen Sie Schutzhandschuhe und- Brille, bevor Sie das Ventil auseinander nehmen.
Bedienungsanleitung DV-5120 VIEWEG So ist sichergestellt, daß die Ventileinstellung, wie in Kapitel 4.4 beschrieben, funktioniert. An der Seite des Ventils befindet sich ein Gewindebohrung. Hier kann die mitgelieferte Haltestange eingeschraubt werden, um das Ventil z.B. an einem Stativ zu befestigen. Das Ventil arbei- tet in jeder Position.
Bedienungsanleitung DV-5120 VIEWEG 4.3 Anschließen der Steuerluft Zu Öffnen des Ventils wird ein minimaler Steuerdruck von 4,5 bar benötigt. Ohne diesen Druck schließt das Ventil durch die interne Federkraft. Zum Anschließen der Steuerluft können Sie den mitgelieferten Druckluftschlauch mit Gerätestecker verwenden.
Operating Instructions DV-5120 VIEWEG 1.1 The DV-5120 The Pinch Tube Valve provides a wide degree of control for continuous or micro shot applications of low to semi-viscous fluids. The “ON/OFF” control is achieved by automatically opening and pinching a molded polyethylene tube assembly.
Operating Instructions DV-5120 VIEWEG 1.3 Scope of delivery The following accessories are included with the DV-5120 valve operating instructions dispensing valve DV-5120 (on this photo with inserted tube insert) tube insert inner-Ø 1,8 mm (Item no. 501787) tube insert inner-Ø 2,5 mm (Item no.
Operating Instructions DV-5120 VIEWEG 2 Safety instructions 2.1 General safety information If this device is used for purposes other than those WARNING described in this operating manual, personal injury or damage to property may result. Only use the device in accordance with the enclosed instructions.
Operating Instructions DV-5120 VIEWEG 3 About your dispensing valve 1 compressed air connection for 5 adjusting knob control air 6 locknut 2 valve body 7 material inlet 3 tube insert (replaceable) 8 fastening possibility for rod mount 4 flange cap...
Operating Instructions DV-5120 VIEWEG 4 Commissioning 4.1 Inserting or changing the tube insert Before maintenance, make sure that the system is not under pressure! Make sure that there is no liquid left in the valve. Wear protective gloves and goggles before disassembling the valve.
Operating Instructions DV-5120 VIEWEG This ensures that the valve setting functions as described in chapter 4.4. There is a threaded hole on the side of the valve. The supplied holding rod can be screwed in here to attach the valve to a tripod, for example. The valve works in any position.
Page 19
Operating Instructions DV-5120 VIEWEG 4.3 Connecting the control air A minimum control pressure of 4.5 bar is required to open the valve. Without this pressure, the valve closes by the internal spring force. To connect the control air, you can use the supplied compressed air hose with quick connect.