Related Manuals for K-array Lyzard-KZ1 I
Summary of Contents for K-array Lyzard-KZ1 I
- Page 1 USER GUIDE Lyzard-KZ1R I ultra-mini point source speaker in a new recessed design Lyzard-KZ1R I ultra-mini point source speaker in a new recessed design...
-
Page 3: Table Of Contents
Index Unpacking (Fig.1) Setup (Fig.2 -> Installation (Fig. 3 -> 1 -2 -3) In-wall installation with screws (Fig. 3.1 -> 2 -3 -4) Adhesive pad (Fig. 3.2 -> 1 -2 -3) Permanent Recessed Installation (Fig. 4, 4.1 -> 1.1-2.2-3.3-4.4) Connecting Loudspeakers in Parallel Service Cleaning... - Page 4 • K-array will not shoulder any responsibilities for products modified This device complies with Restriction of Hazardous without prior authorization. Substances Directive. • K-array cannot be held responsible for damage caused by improper use of the loudspeakers.
- Page 5 K-array customer service at support@k-array.com or contact the official K-array distributor in your country. The Lyzard-KZ1 I is the ultra mini point source speaker in the smallest K-array’s mid-high speaker series. With a very small ultra-resistant milled aluminum enclosure 2.2 x 3.7 1.1 cm with a weight of only 21...
-
Page 6: Unpacking
Check that the following parts are supplied (Fig. 2, 2.1) within the package (fig.1) A. 1x Lyzard-KZ1 I 1x Lyzard-KZ1R I loudspeaker with 5m (164 ft) cable* the cable is directly connected to the speaker through a 2mm Euroblock connector inside the speaker’s rear panel. -
Page 7: Installation
Installation The New KZ1 I and KZ1R I are available in 2 different models here presented. The Lyzard-KZ1 I’s compact 1. Take the little neodymium magnet found into the new design comprehends a unique fully incorporated speaker’s package and take off the grille. (steps... - Page 8 4 mm [ 0,15 in] 4 mm [ 0,15 in] 4 mm [ 0,15 in]...
-
Page 14: Permanent Recessed Installation
K-array power amplifier. permanently, following these instructions carefully. K-array’s Kommander line of amplifiers featuring built- in DSP will operate the Lyzard-KZ1 I and Lyzard-KZ1R I (fig.4) at their optimized performance only with the proper For permanent installation a kit including a mounting... -
Page 15: Loudspeakers In Parallel
K-array service center. impedance. Caution must be taken to maintain the Cleaning load impedance of the Lyzard-KZ1 I and Lyzard-KZ1R I paralleled loudspeakers above the amplifier’s minimum loading impedance. Use only a soft, dry cloth to clean the housing. Do not... -
Page 16: Mechanical Drawings
Mechanical drawings 22mm 11mm 0,9in 0,4in 0,2in 28mm 10mm 22mm 1,1in 0,4in 0,9in 28mm 1,1in 11mm 0,4in Lyzard-KZ1R... -
Page 17: Technical Specifications
Technical specifications Type point source Transducers 0.5” Neodymium magnet woofer Frequency Response 500 Hz – 18 kHz (-6 dB) Max SPL 86 dB peak Coverage V. 140° | H. 140° Power Handling 3,5 W 16 Ω Nominal Impedance Connectors IN + IN- screw terminals Handling &... - Page 19 Designed and Made in Italy K-ARRAY surl Via P. Romagnoli 17 | 50038 Scarperia e San Piero - Firenze - Italy ph +39 055 84 87 222 | info@k-array.com www.k-array.com...
Need help?
Do you have a question about the Lyzard-KZ1 I and is the answer not in the manual?
Questions and answers