Table of Contents
Advertisement
REPLACEMENT OF DOOR OPENING TYPE
Precaution
1.
Before reversing the door, first of all, you should take out food
and accessories like shelves or trays which arenot fixed in the
fridge-freezer.
2.
Use Torque Wrench or Spanner to fix or remove the bolt.
3.
Do not lay the fridge-freezer down. This will cause problems.
4.
Be careful not to drop the doors in disassembling or assembling.
How to Reverse the Door
1.
Separate the screw
after separating the nut
3
left of the refrigerator door handle
refrigerator door handle . Separate the freezer door
handle in the order in which you separating the refrigerator
door handle
. (The hidden handle does not need this
1
procedure)
3
2
2
3
2
2.
Separate the screw
5
the cap
of bottom cover and install it on the
7
corresponding position on the right side. Separate the
hinge lower right
and the pin
9
screw
. Install the bolt into the corresponding left hole
8
on the hinge lower. Separate the freezer door , then
remove the CAP
on the door and install it on the
12
corresponding position on the right side. Separate the door
stop
after your separating the screw , then install the
door stop on the corresponding position on the left.
12
7
6
5
24
3.
Separate the cover of hinge upper , separate the two
wire
. Separate the screw , separate the hinge middle
16
, then separate the refrigerator door
1 8
and install it on the corresponding position on the right.
Separate the door stop
, then install the door stop on the corresponding position
2 1
on the left. Separate the screw
upper right (Hinge Upper) .
Note: Reversing the doors is not covered by the
warranty.
All manuals and user guides at all-guides.com
on the
2
, then separate the
1
1
1
4
and bottom cover , then separate
6
after separating the
10
11
13
10
9
8
11
14
13
15
23
16
15
17
.Separate cap
19
after your separating the screw
22
, then separate the hinge
23
24
4.
Remove two small caps on the front of the cover front
with a screw driver, then separate the screw
the cover front . Move the wire
4
front
and the screw. Take the small caps out of the alternate
2 3
bag, then install the small caps.
Note: It's unnecessory to change door switch wire .
34
5.
Remove the small cap
separate the small cap
corresponding position on the right. Install the small cap
then install the small cap
the right.
6.
Install the hinge lower
the hinge middle
the freezer door, take the hinge upper
bag and install it on upper left. Pull out the wire
individual holes and connect these cables. Take the small caps
out of the alternate bag, then install the small caps. Install
3 1 3 2
base cover
6
31
30
20
7.
Separate the cap
into the left screw hole (you can see this hole after the left handle
is removed). Install the handle and the screw which previously
separated on the corresponding position on the right. (The
hidden handle does not need this procedure) Then Installation
completed.
-7-
18
19
17
20
22
21
to left, install the cover
23
25
26
A
27
23
19
24
of the refrigerator door
7
27
. Move the cable
28
on the corresponding position on
27
17
18
11
10
9
5
6
and the freezer door
10
. Separate the cap
on the freezer. Install
18
34
out of the alternate
30
.
32
3
2
26
29
3
2
on the right side of the door, then install it
33
23
and . Separate
24
A
28
29
, then
19
from left to the
29
,
28
, then install
11
from the
26 29
33
Advertisement
Table of Contents
