Table of Contents
Advertisement
NOTE: Although Push n' Learn™ can be used to modify load binding for wireless switches, Wattstopper recommend using the DLM
Config App for ease of use and available features.
NOTE: Push n' Learn is not available for wireless switches paired to hybrid rooms with wired controllers.
Load Selection Procedure
In situations in which there is more than one load in a room, the configuration button allows access to Push n' Learn™ technology to
change the binding relationship between control devices and loads.
NOTE: PnL cannot be used to change the binding on wireless sensors, although it is possible to enter PnL mode from a sensor.
Step 1 Enter Push n' Learn
Press and hold the Config button (on any DLM device) for 3 seconds.
The LED on the LMSW-6xx-S begins to blink red. The LED on all switches and sensors, and the Config LED on room controllers in the
local room network will also blink red. The LEDs will continue to blink until you exit PnL mode.
NOTE: If a switch or sensor is currently "asleep", it will not blink. To ensure the switch is currently awake before initiating PnL, press a
button first, or initiate PnL from that switch.
All loads in the room turn OFF immediately after entering PnL, then one load will turn ON. This is Load #1. On the LMRC-611 for that
load, the blue Load LED will also be ON.
Step 2 Load selection
Press and release the Config button to step through the loads connected to the DLM Local Network. Each time you press the Config
button, the next load in the series will turn ON along with its Load LED, and the previous load will turn OFF.
To view the current status of the button or paddle, press the button or paddle once. The LED on the paddle will blink once blue or red,
and then revert to blinking red. To bind or unbind a button or paddle from the load press and hold that button or paddle on the wireless
switch. The LED will switch to the other color and stay lit for one second and then resume blinking red. Each time you press and hold
the paddle or button, it will cycle to the next option:
• Blue – The button or paddle is bound to the load.
• Red – The button or paddle is not bound to the load.
Step 3 Exit Push n' Learn
Press and hold the Config button until the red LED turns OFF, approximately 3 seconds.
When you reset the LMSW-6xx-S, the Channel and Network ID will return to their default values, and if the switch was previously paired,
it will no longer be connected to that room network. All DLM parameters are also returned to their default values.
To reset the switch, press the Config button 10 times. The LED will blink green each time the Config button is pressed (except for the
7th press which will blink blue). On the 10th press, the LED will blink red. Then it will turn red again and then briefly turn green and then
blue, indicating it is rebooting.
NOTE: You can also reset the LMSW-6xx-S from the DLM Config App or LMCS (the LMSW-6xx-S must be woken up before resetting).
NOTE: During battery replacement, some electrical components are exposed to static discharge from the user which could damage the
switch. It is recommended to discharge any static from your person prior to proceeding. Contacting the switch's battery holder
will equalize charge and avoid damage from static discharge.
To replace the battery:
1. Remove the faceplate from the switch.
2. Locate the prying location at the bottom left corner of the switch frame (slightly below the
Legrand badge), as shown. Insert a small prying tool and pull the corner of the switch
frame away from the wall. The switch will detach from the mounting plate with frame and
buttons intact.
3. Locate the battery at the rear of the device. Remove the battery and replace with a new
CR2032 battery.
4. Press the switch back into the mounting plate, and reinstall the faceplate. Removed
battery is non-reusable and should be disposed off properly.
UNIT ADJUSTMENT USING PUSH N' LEARN
RESETTING THE LMSW-6XX-S
REPLACING THE BATTERY
7
C R 2 0
3 2
Advertisement
Table of Contents
