Summary of Contents for LEADING EDGE SAFETY X-CALIBUR
Page 1
It is the responsibility of the purchaser to understand and convey explicit instruction to each user. The AES Manufacturing/Leading Edge Safety X-CALIBUR complies with the requirements of the Federal Occupational Safety and Health Administration (OSHA) when set up and used according to the manufacturers’...
Hoisting or Lifting_____________________________________ General Safety_______________________________________ Before Each Use______________________________________ Positioning the Unit____________________________________ Special Applications___________________________________ Making Connections___________________________________ Maintenance, Care & Storage____________________________ In The Event of A Fall__________________________________ APPENDIX Appendix A - X-Calibur Engagement Box Removal & Installation_ Inspection & Maintenance Log____________________________ 18...
ANUAL 1.0 Standards and Requirements 1.1 The X-CALIBUR, manufactured by Leading Edge Safety LLC, is a dynamic anchor designed to dissipate the energy generated from a fall event into the surrounding substrate and arrest a fall. The X-CALIBUR is capable of supporting a Maximum Arresting Force (MAF) of 1,800lbs for up to (1) worker on approved substrates.
The X-CALIBUR may be used where worker mobility and fall protection are required. See WWW.OSHA.GOV for all regulations and standards. 2.2 The X-CALIBUR allows for up to one worker to be tied-off for fall arrest to the Fall Arrest Attachment Point. See the following definitions (Section 3.0): FALL ARREST ATTACHMENT POINT 3.0 DEFINITIONS:...
NSTRUCTION ANUAL 4.0 USE AND LIMITATIONS LOAD REQUIREMENTS—Before the X-CALIBUR is hoisted to any roof surface, the user must verify that the deck assembly can accommodate the live load requirements of the X-CALIBUR. Approximate Unit Weight: 572 lbs Tire Footprint: 2.5” x 4.75”...
5.0 HOISTING OR LIFTING Loads may slip or fall if the X-CALIBUR is not hoisted or lifted properly and may result in injury or death. Never hoist or lift the X-CALIBUR if any of the hoisting rings/fork pockets are damaged.
ANUAL 6.0 GENERAL SAFETY (Continued) Only use the X-CALIBUR on completed roof assemblies for which it has been tested. (Reference Sect 4.2 Approved Substrates) Always lower the unit using the locking handle so the frame is resting on the substrate when not in use.
Page 15
Once the unit is properly positioned, ensure rear axle is parallel to the leading edge, raise the handle to lower the frame to the substrate, and deploy the outriggers. FIG 8-3 8.3.A To lower the X-CALIBUR frame to the ‘frame down, brake position’, apply & maintain pressure on the handle with one hand. 8.3.B While maintaining handle pressure with one hand, use your other hand to pull the locking pin out and release the handle.
The X-CALIBURmay be used for fall arrest in dissimilar height applications where worker(s) are located on a surface lower than the surface the X-CALIBUR is positioned on and when properly set up and used with an SRL ANSI approved for leading edge conditions. FIG 9-1 FIG 9-1 10.0 MAKING CONNECTIONS...
12.2 Follow your company policy and site-specific rescue plan. 12.2 Before attempting to rescue a fall victim connected to the X-CALIBUR, ensure the X-CALIBUR is stable with the claw engaged into the substrate, both tires, and outriggers are contacting the walking/working surface.
Remove the six 3/8-16 x 1” Flange Head Screws (12) STEP 3 Remove the X-CALIBUR Engagement Box Assembly STEP 4 Return the damaged Engagement Box Assembly to Leading Edge Safety: Leading Edge Safety, LLC 1400 Taney St North Kansas City, MO 64116 888-990-2990 FIG A-1...
ALIBUR NSTRUCTION ANUAL MOBILE FALL CART INSPECTION AND MAINTENANCE LOG PLEASE COPY THIS LOG, FILL IT OUT BEFORE EACH USE, AND KEEP IT IN YOUR RECORDS. EQUIPMENT MODEL #: ____________________ EQUIPMENT SERIAL #: ____________________ DATE OF PURCHASE: ____________________ INSPECTION DATE: ____________________ Corrective Action Inspection Item...