Illustrated Description; Maintenance Schedule - stayer GX800 Operating Instructions Manual

ILLUSTRATED DESCRIPTION

1 Fuel cap
2 Fuel level indicator
3 Remote starter
4 Control panel
5 Starting grip
6 Command the fuel shutoff valve
7
Maintenance cover
8
Electrical output socket 230V 50Hz
9 Output voltage indicator
10 ON/OFF/START Switch
11 Electrical Grounding
12 Output overload protector
13 Spark plug
3_OPERATING INSTRUCTIONS
PLACEMENT AND TESTING
Be sure to check the generator on a level surface with
the engine stopped.
START 4T
Before starting the engine, disconnect any load from
the receptacle.
Set the fuel valve in the "ON"-position.
To start a cold motor shove the choke lever all the way to
the left. To restart a hot motor set the choke lever half-way.
Shove the choke to about halfway to restart a warm motor.
A hot motor will not start if there is too much fuel in
the cylinder.
If this happens, wait five to ten minutes before trying
again. Shove the choke completely to the right and
the motor should start.
Set the motor switch in the "ON"-position.
Pull slightly on the start cord 5 until you feel resistance
and then yank hard and swiftly.
Do not let the start cord retract by itself: guide it back
by hand. Hold the carrying handle firmly to prevent
the generator from falling over when you pull the
start cord.
Press the choke in completely after the engine is started.
If the engine stops and will not restart, check the
engine oil level before troubleshooting in other areas.
OVERLOAD
The team cut the electricity supply if a consumer exceeds
the maximum, to restore supply shut off the engine and
press the circuit breaker 12.
STOPPING THE ENGINE
To stop the engine in an emergency, turn the engine
switch to the OFF position.
In normal use:
Switch off the connected equipment and pull the inserted
plug out.
Turn the engine switch to the OFF position.
Turn the cap lever fully counter clockwise to the "OFF"
Is the output indicator on?
NO
Is the overload
position.
indicator on?
Yes
Be sure both the fuel cap lever and the engine switch
Does the electrical equipment
work when plugged in directly?
are in "OFF" position when stopping, transporting
and/or storing the generator.
4_MAINTENANCE AND SERVICE INSTRUCTIONS

MAINTENANCE SCHEDULE

Is the electric
circuit breaker intact?
PLUG: Every 50h or once a month.
AIR FILTER: Every 150h or once every 3 months.
FUEL FILTER: Every 150h or once every 3 months.
NOTE:
1 Log hours of operation to determine proper
maintenance.
Regular Service Period (1)
2 Service more frequently when used in dusty areas.
Item
3 Perform at every indicated month or operating hour These items should be serviced by an authorized
interval, whichever comes first.
dealer.
Engine oil
OIL
Air cleaner
Spark plug
Use high-detergent, premium quality 4-stroke engine oil,
Spark arrester
certified to meet or exceed automobile manufacturer's
Valve clearance
Fuel tank and filter
requirements.
Fuel line
Select the appropriate viscosity for the average
temperature in your area.
-
SAE Viscosity Grades
Single
viscosity
Multi
viscosity
-20 -10
0 20
Ambient Temperature
Mix the oil with the fuel in a container other than the
generator tank and fill the tank once the mixture is
homogeneous. Never use the tank as a container for
mixing fuel and oil.
- The mixing ratio is 50 parts petrol to 1 part oil, 50 : 1.
FUEL
Turn the fuel cap 14 lever to "OFF" position before
transporting.
Use automotive fuel (Unleaded or low leaded is preferred
to minimize combustion chamber deposits). Before filling
the tank, make sure that you have mixed the fuel and oil
correctly as indicated in the "OIL" section.
!! Don't use fuel containing alcohol: Fuel system
damage or engine performance problems resulting
from the use of fuels that contain alcohol are not
covered under the warranty.
After refuelling, tighten the fuel filler cap securely.
Gasoline is extremely flammable and is explosive under
certain conditions. Refuel in a well-ventilated area with
the engine stopped.
Do not smoke or allow flames or sparks in the area where
- 17 -
Send the generator to an
NO
authorized dealer.
Restart after turning off the
NO
overload indicator.
Yes
Send the generator to an
authorized dealer.
Yes
Replace the electric equipment.
Repair the electric equipment.
NO
Replace the electric circuit breaker.
Yes
Send the generator to
an authorized dealer.
Check level
Change
Check
Clean
(2)
Check-adjust
Clean
Check-adjust
Clean
Check
Every 2 years (Replace if
necessary) (3)
10W
20W
20
30
20W - 40.20W-50
15W - 40.15W-50
10W - 40
100W - 30
0 10 20 30 40ºC
40 60 80 100ºF
es
it
gb
fr
p
el
(3)
(3)
40