Table of Contents
Advertisement
Quick Links
Application Note
CDPX-X-E1-W-xx
Manual
This Application Note describes the main features of the Festo operator
panels. The manual refers to the following models CDPX-X-E1-W-7,
CDPX-X-E1-W-10 and CDPX-X-E1-W-15. This operational guidelines de-
scribed below is information which relates to the device, installation,
transportation, storage, assembly, use and maintenance.
CDPX-X-E1-W-xx
100443
Advertisement
Table of Contents
Related Manuals for Festo CDPX-X-E1-W Series
Summary of Contents for Festo CDPX-X-E1-W Series
- Page 1 CDPX-X-E1-W-xx Manual CDPX-X-E1-W-xx This Application Note describes the main features of the Festo operator panels. The manual refers to the following models CDPX-X-E1-W-7, CDPX-X-E1-W-10 and CDPX-X-E1-W-15. This operational guidelines de- scribed below is information which relates to the device, installation, transportation, storage, assembly, use and maintenance.
- Page 2 Festo SE & Co. KG. Festo SE & Co KG reserves the right to make modifications to this document in whole or in part. All brand and product names are trademarks or registered trademarks of their respective owners.
-
Page 3: Table Of Contents
Table of contents Components/Software used ........................5 Software Used ............................. 5 Hardware Used ............................5 APPLICATION NOTE DESCRIPTION ......................6 Product Overview ............................7 Standards and Approvals ........................... 8 Product Identification ..........................9 Technical Specifications ........................... 10 Technical Data ............................12 Dimensions ............................... -
Page 5: Components/Software Used
Components/Software used Components/Software used Software Used Type/Name Software Version Festo Designer Studio V4.5.0.224 Table 1.1: Software used Hardware Used Type/Name Firmware Version CDXP-X-E1-W-7 Config-OS 1.3.638 CDXP-X-E1-W-10 Main-OS 1.3.638 CDXP-X-E1-W-15 Bootloader 1.0.11 Table 1.2: Hardware used Application Note – CDPX-X-E1-W-xx Page 5 of 27... -
Page 6: Application Note Description
APPLICATION NOTE DESCRIPTION APPLICATION NOTE DESCRIPTION The manual contains safety standards that must be respected for the personal safety and to avoid damage. Indications of attention are divided into three levels of severity: DANGER: indicates a failure to observe safety rules and such failure may cause death or serious injuries. -
Page 7: Product Overview
Product Overview 3 Product Overview Festo CDPX-E1 HMI products combine state-of-the-art connectivity features and top performance in a great design. Products have been designed as IoT edge devices with the combination of a powerful controller with networking capability (up to 3 Ethernet networks) and outstanding com- munication options including client/ server OPC UA. -
Page 8: Standards And Approvals
(RoHS) Directive 2011/65/EU In compliance with the above regulations the products are CE marked. Products described in this manual may have other approvals and certificates. Please refer to product datasheets available at www.festo.com Page 8 of 27 Application Note – CDPX-X-E1-W-xx... -
Page 9: Product Identification
Product Identification 5 Product Identification The product may be identified by the indications in the rear cover. You will have to know the type of unit you are using for correct usage of the information contained in the guide. An example of the information reported is shown below: product name CDPX-X-E1-W-7 part number... -
Page 10: Technical Specifications
Technical Specifications Technical Specifications Projected capacitive – Multitouch Touchscreen technology 3V 50mAh Lithium, rechargeable, Back-up battery not user replaceable, model VL2330. Automatic Fuse RS232, RS 485, RS 422 software configurable Serial Port Flash 4GB (8GB for CDPX-X-E1-W-15) 1GB (2GB for CDPX-X-E1-W-15) Clock/Calendar with back-up battery Hardware clock <100ppm... - Page 11 Technical Specifications Voltage dips, short interruptions and Port: AC mains; Level: voltage variations immunity test 100% duration: 1 cycle and 250 cycles (50Hz); 1 cycle and 300 cycles (60Hz); 40% duration: 10 cycles (50Hz); 12 cycles (60Hz); 70% duration: 25 cycles (50Hz); 30 cycles (60Hz);...
-
Page 12: Technical Data
Technical Data Technical Data Model CDPX-X-E1-W-7 CDPX-X-E1-W-10 CDPX-X-E1-W-15 Display / TFT Color / LED TFT Color / LED TFT Color / LED Backlight Colors Resolution 800 x 480 1280 x 800 1366 x 768 Diagonal (inches) 7” widescreen 10.1” widescreen 15.6”... -
Page 13: Dimensions
Technical Data Dimensions MODEL CDPX-X-E!-W-7 187mm/7.36” 147mm/5.79” 176mm/6.90” 136mm/5.35” 47mm/1.85” 8mm/0.31” CDPX-X-E1-W-10 282mm/11.10” 197mm/7.80” 271mm/10.67” 186mm/7.32” 56mm/2.20” 8mm/0.31” CDPX-X-E1-W-15 422mm/16.60” 267mm/10.50” 411mm/16.18” 256mm/10.00” 56mm/2.20” 8mm/0.31” Application Note – CDPX-X-E1-W-xx Page 13 of 27... -
Page 14: Installation Environment And Procedure
Technical Data Installation Environment and Procedure Avoid prolonged exposition to direct sunlight to avoid the risk of overheating the device. The equipment is not intended for installation in contact with corrosive chemical compounds. Check the resistance of the front panel to a specific compound before installation. Do not use tools of any kind (screwdrivers, etc.) to operate the touch screen of the panel. -
Page 15: Safety Instructions
Technical Data Safety instructions Installation Procedure Place the fixing brackets contained in the fixing kit as shown in figure Tightening torque: 130Ncm or screw each fixing screw until the bezel corner gets in contact with the panel. Application Note – CDPX-X-E1-W-xx Page 15 of 27... -
Page 16: Connections
Connections Connections 1. USB Port V2.0, max. 500 mA - for maintenance only 2. Ethernet port 2 (10/100Mb) 3. Ethernet port 1 (10/100Mb) 4. Serial Port 5. Ethernet port 0 (10/100/1000Mb) 6. Power Supply 7. 2x Expansion slot for Plugin module 8. -
Page 17: Serial Port
Connections Serial Port The serial port is used to communicate with the PLC or with another type of controller. Different electrical standards are available for the signals in the PLC port connector: RS-232, RS-422, RS-485. The serial port is software programmable. Make sure you select the appropriate interface in the programming software. -
Page 18: Optional Plug-In Modules
Connections Optional Plug-in Modules CDPX-X-E1 series panels have several optional plugin module. Multiple modules configurations are possible Slot #1 Slot #3 Slot #2 Slot #4 Slot#2 and Slot#4 are available only if plugin module has a “bus extension connector” Note: It is not possible to stack two modules that are using the same type of interface like the CANo- pen interface. -
Page 19: Optional Plug-In Module Installation Procedure
Connections Optional Plug-in module installation procedure CDPX-F-CO / CDPX-EA-V2 CDPX-EA-V1 Application Note – CDPX-X-E1-W-xx Page 19 of 27... -
Page 20: Power Supply, Grounding And Shielding
Power Supply, Grounding and Shielding Power Supply, Grounding and Shielding The power supply terminal block is shown in the figure below 3 conductor 1,5mm2 wire size minimum, minimum temperature conductor rating 105°C. Note: Ensure that the power supply has enough power capacity for the operation of the equipment. The unit must always be grounded to earth with 1,5mm2 wire size minimum. -
Page 21: Battery
Battery 10 Battery These devices are equipped with rechargeable Lithium battery, not user-replaceable. The following information is maintained by the battery: hardware real-time clock (date and time) Charge: At first installation must be charged for 48 hours. When the battery is fully charged, it ensures a period of 3 months of data back-up at 25°C. Application Note –... -
Page 22: Special Instructions For Use
Special Instructions for Use 11 Special Instructions for Use • The equipment shall only be used in an area of not more than pollution degree 2, as defined in IEC/EN 60664-1. • The equipment shall be installed in an enclosure that provides a degree of protection not less than IP 54 in accordance with IEC/EN 60079-15. -
Page 23: Getting Started
Designer Studio to access the network. Create an Update Package using Designer Studio and copy it to a USB Flash drive. Updated product documentation is available at www.festo.com. Application Note – CDPX-X-E1-W-xx Page 23 of 27... -
Page 24: System Settings
System Settings 13 System Settings CDPX-X-B-../E1-../E2-.. HMI products have a system settings interface to allow configuration of system options. The user interface of System Settings is based on HTML pages accessible from the HMI screen or re- motely using a Web browser Chrome v44 or higher using port 443. To connect enter “https://IP/machine_config”... - Page 25 System Settings Activation of System Settings in User Mode: Factory default status Press “System Setting” button on the HMI screen Designer Studio runtime running Recall context menu and select “System Settings”. To recall the context menu click and hold any unused area of the touchscreen for a few seconds.
- Page 26 System Settings and other system components). Standard user has some limitations. Note: Additional information on System Settings are available in dedicated manual Page 26 of 27 Application Note – CDPX-X-E1-W-xx...
-
Page 27: Unpacking And Packing Instructions
Unpacking and Packing instructions 14 Unpacking and Packing instructions CDPX-X-E1-W-7 / CDPX-X-E1_W-10 CDPX-X-E1-W-15 To repack the unit, please follow the instructions backwards Application Note – CDPX-X-E1-W-xx Page 27 of 27...
Need help?
Do you have a question about the CDPX-X-E1-W Series and is the answer not in the manual?
Questions and answers