To Reset To The Beginning Of The Color Sequence; Replacing Led Board And Driver (Pcb); Pool Clamp Removal; Small Light Driver (Pcb) Replacement - Jandy WaterColors CPLVRGBWS30 Installation And Operation Manual

Page 10
ENGLISH
6.2 To Reset to the Beginning of the Color
Sequence
Turn the light OFF, wait four (4) to five (5) seconds, then
turn ON, the light will return to the beginning of the color
cycle (Alpine White).
NOTE:
If an AquaLink RS control system is being used the
®
color set can be selected using the indoor controller.
NOTE:
To synchronize colors on multiple Jandy WaterColors
RGBW LED Light systems wired to separate switches,
perform the above actions on all of their switches
simultaneously. All Jandy WaterColors RGBW LED
Lights will synchronize automatically if activated by the
same switch. No other accessories are required.
Section 7. Replacing LED Board and
Driver (PCB)
WARNING
Always disconnect power to the color light at the
circuit breaker before servicing the light. Failure
to do so could result in death or serious injury to
installer, serviceman, pool or spa users or others
due to electrical shock.
1. Turn off the main electrical switch or circuit
breaker, as well as the switch, which operates the
underwater light.
2. Be sure to have the following items:
• A new lens gasket.
• A light driver board. See Table 2 for specification.
WARNING
Replace light driver with the same type. Failure
to replace the light driver with the same type will
damage the light assembly and may cause an
electrical hazard resulting in death or serious injury
to pool or spa users, installers, or others due to
electrical shock, and may also cause damage to
property. Be sure the power is switched OFF before
removing or installing PCB. Allow PCB to cool
before replacing.
3. To remove the light assembly, unscrew the special
pilot screw at the top of the face ring, remove
light assembly from niche and gently place
assembly on the deck. It is not necessary to drain
down the pool. See Figure 6.
Jandy WaterColors RGBW LED Lights | Installation & Operation Manual
®
POOL LIGHT
ASSEMBLY
Power
Niche
Cord
Bonding
cable
Figure 6. Removing the Jandy WaterColors RGBW
LED Light Assembly for Light Driver
Replacement
Table 2. Light Specifications
Jandy Model
WaterColors RGBW
LED Large Light
WaterColors RGBW
LED Large Light
WaterColors RGBW
LED Small Light
WaterColors RGBW
LED Small Light
WARNING
Be sure to keep the special pilot screw from this
underwater light. This screw mounts and electrically
grounds the housing securely to the mounting ring
and wet niche. Failure to use the screw provided
could create an electrical hazard, which could result
in death or serious injury to pool or spa users,
installers or others due to electrical shock.
7.1

Pool Clamp Removal.

1. Loosen the Phillips head screws (six (6) for small
light, eight (8) for large light) to allow the bottom
clamp to be removed from the face ring assembly.
Do not remove the screws or the retaining rings.
The retaining rings prevent the screws from
falling free from the bottom clamp and also aid in
ease of assembly.
2 Remove the bottom clamp, the face ring
assembly, the glass lens, and the gasket from
the fixture. Remove the silicone gasket from
the lens. Refer to Section 9, Exploded View and
Replacement Parts.
NOTE:
Always install a new lens silicone gasket whenever
disassembling the light.
POOL WALL
Unscrew pilot screw
and pull top of light
1
assembly away from
pool wall
PILOT SCREW
2 Push up on
bottom of
light assembly
Light Driver
Fixture
(PCB)
Voltage
Part Number
12 Volt AC R0739500
120 Volt AC R0739400
12 Volt AC R0785700
120 Volt AC R0739600
Power
Nic
Cord
Bonding
cable