Advertisement
TABLE OF CONTENTS
SIGNAL WORDS
This manual uses SIGNAL WORDS to direct the reader's attention to important safety-related messages. These
messages describe uses of the product that could result in personal injury or property damage. Each signal word
corresponds to a specific hazard level
Identifies a hazardous situation which, if not avoided, COULD result in DEATH or SERIOUS
INJURY.
Identifies practices likely to result in product/property damage, such as operation that might damage
the product.
SAFETY INSTRUCTIONS
Vestil strives to identify foreseeable hazards associated with the use of its products. However, material handling is
dangerous and no manual can address every conceivable risk. Ultimately, the most effective way to avoid injury is for the
operator to exercise sound judgment whenever using this machine.
Improper or careless operation might result in serious personal injuries or death.
Failure to read and understand the entire manual before installing, using or servicing the product constitutes misuse.
Read the manual to refresh your understanding of proper use and maintenance procedures.
Do not operate the crusher with the loading door open.
Do not operate the machine if the emergency stop switch does not function properly.
Do not stand in front of the door during operation.
Keep clear of all moving parts during operation.
High pressure oil easily punctures skin which can cause injury such as gangrene. If a hose or coupling develops a
leak, repair the leak before operating the crusher.
Do not continue to use the crusher if it is damaged or makes unusual noises during operation.
Do not change the pressure relief valve setting! In particular, do not increase the setting.
Do not clean out drum crusher unless power is disconnected.
Do not attempt to crush smooth-walled drums with this machine. Drums must be ribbed to crush properly.
Do not attempt to crush drums filled with items or materials. Only use this unit to crush empty drums.
Do not use brake fluids or jack oils in the hydraulic system. Only use AW-32 hydraulic oil or its equal.
Do not modify the product in any way. Unauthorized modifications might make the lifter unsafe to use and
automatically void the
LIMITED WARRANTY
DO NOT use this device unless every label is in place and easily readable. See
HYDRAULIC CIRCUIT DIAGRAM 22-125-016 REV. C
GA2 = System operating pressure; should never exceed 3000psi.
need to test.
GA4 = No need to test.
cylinder (crush or compact).
TABLE OF CONTENTS
.
WARNING
!
on either
GA5 = Pressure required to raise cylinder to home position.
UL-GA = Pressure at which large pump unloads.
Copyright 2023 Vestil Manufacturing Co.
Rev. 1/16/2023
p. 18
or 19.
Item
Part no.
1
22-627-017
ASSEMBLY, MANIFOLD
MANIFOLD, HDC_905 W/ DECOMPRESSION
1.1
22-127-021
CHECK
4-WAY, 3-POS, TANDEM CENTER, A & B
1.2
99-153-065
BLOCKED, DO5
1.3
99-153-077
check valve, nose in, side out, size 08
VALVE, CHECK, PILOT-TO-OPEN, 30 PSI
1.4
22-153-003
CRACK, 3:1, SIZE 10
VALVE, CHECK, NOSE-IN/SIDE-OUT, 25 PSI
1.5
99-153-068
CRACK
1.6
99-153-078
RELIEF VALVE, 200-350 BAR, SIZE 10
VALVE, CHECK, NOSE-IN/SIDE-OUT, 5 PSI
1.7
99-153-035
CRACK, VC10
VALVE, SEQUENCE, INTERNAL PILOT AND
1.8
99-153-028
DRAIN
6.5HP, 3 PH, 1740/1440 RPM, 184T, 9T
2
22-135-010
SPLINE 230/460, TEFC
PUMP, .97/.499 CU IN, , 9T SPLINE SHAFT, 2
3
22-143-001
SECTION
99-021-926-
4
PISTON CYLINDER, 4 x 36, FLANGE MOUNT
001
5
22-031-023
SPIN-ON FILTER, 10 MICRON
6
22-023-004
RESERVOIR, HYDRAUILC, PLASTIC
7
99-031-035
SCREEN, SUCTION, 1" NPT
FITTING, HYDRAULIC, 04MORB HOLLOW
8
99-116-005
HEX PLUG
GA1 = Filter head pressure; should never exceed 25psi. GA3
PS3 = (NC switch) Coil b disabled when pressure ˃300psi.
HDC-905 MANUAL
LABELING DIAGRAM
on. p. 17.
Description
GA6 = Pressure required to extend
Page 2 of 19
Qty.
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
7
=
No
Advertisement
