TABLE OF CONTENTS GENERAL INFORMATION DESCRIPTION IDENTIFICATION DAMAGE DAMAGE CLAIM PROCEDURE INSTALLATION GENERAL INFORMATION INSPECTION PRE-TEST DATA CABLE INSTALLATION ELECTRICAL CONNECTIONS CONTROL CONSOLE OPERATION SCOREBOARD POWER CONSOLE DISPLAY CONSOLE POWER INITIALIZING SCOREBOARD TIME SETTING AND CONTROL FINAL MINUTE 1/10 SECOND TIME OPTION TEAM SCORES HORN BONUS INDICATOR...
1. GENERAL INFORMATION 1.1 DESCRIPTION Your All-American scoreboard has been carefully inspected and tested before leaving the factory. It is possible, however, that components may be loosened or forced out of adjustment in transit. If this occurs, follow the troubleshooting guide (section 4). If equipment then fails to operate, contact immediately: ALL-AMERICAN Service Department EVERBRITE LLC...
make out a Concealed Damage Report. Fifteen days after delivery are allowed, so this should be done promptly or it is impossible to process this claim. Advise EVERBRITE corporation of necessary replacement parts, or repairs. Consignee will be invoiced and then should file a claim with the carrier to recover charges. To file your claim follow this procedure: (A) Cost of replacement parts or repair charges are invoiced to the carrier by the consignee.
Pre-Test Before installing the scoreboard, pre-test all functions. (A) Connect the scoreboard to a 20 AMP, 120 Volt AC circuit. (B) Plug the control console into the top of the scoreboard. (C) Test operate all functions on the scoreboard according to operating instructions in section 3 of this manual.
Console Display The 2 line by 20 character Liquid Crystal Display module displays the scoreboard information entered from the keyboard. The following information is displayed during normal operation: Time, Home and Guest scores, Home and Guest Team Fouls, Period, Home and Guest Bonus, Ball Possession, Auto Horn Enable, and 1/10 Second Enable.
Push RESET to return the timer to the previously set value. Final Minute 1/10 Second Option The control console is capable of displaying 1/10 second during the final minute of the period. Push FINAL MIN 1/10 to enable the scoreboard to display the 1/10 second during the final minute of the period.
An 'H' is displayed on the LCD when this function is enabled. Bonus Indicators Push Home or Guest BONUS to illuminate the appropriate bonus indicator. A '<B' or 'B>' will be displayed when the bonus is illuminated. 3.10 Period Indicators Push PERIOD once to increment the period indicator.
Test Equipment A simple analog or digital voltmeter will be sufficient for all user repairable problems. Printed circuit boards requiring troubleshooting should be returned to the factory. Troubleshooting Whenever possible, follow the troubleshooting guides prior to contacting the customer service department.
Page 10
(D) The scoreboard digits light, the console works, but there is no control of the scoreboard. Check the voltage between the black and red wires in the junction box with a voltmeter set on the 3 VDC or higher scale. The voltage should read somewhere between 2-3 VDC when the console is working properly.
5.2 Scoreboard Controller Assembly Parts figure 2 CONTROLLER ASSEMBLY REPLACEMENT PARTS LIST (MP-2209 Controller Assembly) fig.& MFG PART VENDOR index NUMBER DESCRIPTION PART # 180156 Controller Assembly 180156 150366 Receiver PCB Assembly 150366 *** PROGRAM 3MP-CNT-V00*** 150368 Driver PCB Assembly, 5 Position A4-A5 150368 EL055800...
6.7 Microprocessor 4 X 7 Lamp Pattern (8 Bit) MICROPROCESSOR 4 X 7 (8 BIT) LAMP PATTERN...
Page 21
6.8 Figuregram Wiring 8 BIT FIGUREGRAM WIRING...
Page 22
Jumper Location on 5 Position System JUMPER LOCATION 6.10 Triac Placement The triac is the switch that controls the figuregram lamps. The triacs for any given figuregram are adjacent to the twelve pin connector on the driver board that controls that figuregram. Shown below is the triac placement and bit designation relative to the figuregram bit pattern.
Need help?
Do you have a question about the All American Scoreboards MP-2209 and is the answer not in the manual?
Questions and answers