Related Manuals for Alemite 7334-B
Summary of Contents for Alemite 7334-B
- Page 1 Service guide Heavy-duty hose reels Model -B, -B, -B Date of issue November Form number Version ...
- Page 2 Contents Declaration of Conformity* .. U.K. Declaration of Conformity* .. Safety* .........
-
Page 3: Declaration Of Conformity
Machinery Directive //EC I, the undersigned of Alemite, L.L.C., do hereby declare that the equipment specified above, in its intended use, conforms to the requirements of the above directives and harmonized standards at the time of placing the above product on the market. - Page 4 Year of CE: I, the undersigned of Alemite, L.L.C., hereby declare that the equipment specified above, in its intended use, conforms with all requirements of the U.K. legislation Supply of Machinery (Safety) Regulations No. by the time of placing it on the market.
-
Page 5: Explanation Of Signal Words For Safety
Safety* Explanation of signal CAUTION Do not operate equipment without words for safety wearing personal protective gear. The assembly must be installed, maintained Wear eye protection. Protective and repaired exclusively by persons familiar equipment such as dust mask, non-skid with the instructions. - Page 6 Description Fig. Reel models -B, -B and -B CAUTION 3 / in Install these reels at a height no greater 7 / in (98 mm) than ft (6.1 m) from the floor to (200 cm) 17 32 ∅...
- Page 7 Service hints Refer to the overhaul procedures for details. ) Observe the color of the rivet on the power spring cassette. Identifies the power spring ) Use care during assembly of sheave and power spring onto base and shaft assembly . Ratchet can interfere waith pawl.
-
Page 8: Clean And Inspect
Sheave and power spring Overhaul Remove nut () that secures the latch assembly pawl assembly to the base assembly. . Remove the latch pawl assembly from the base assembly. Model dependent step NOTE Refer to fig. IPB, page for compo- ... - Page 9 Sheave and power spring Assembly Install retaining ring () onto the pawl assembly shaft. Install pawl spring () into the eye on NOTE the pawl (→ fig. , page For proper Position sheave assembly () bearing Prior to assembly, certain components orientation).
-
Page 10: Bench Test
Fig. Screw the swivel assembly into the base and shaft assembly. Heavy-duty hose reels - section view . Tighten the swivel assembly securely. Medium- and high-pressure swivel assemblies Screw ° union ( or ) [with thread sealant] into the swivel body and stud assembly. - Page 11 Latch lockout Setting spring tension Loosely attach the delivery hose to the sheave assembly with u-bolt (), washers () and wing nuts (). Do not extend the hose from the reel too CAUTION Rotate the sheave assembly to wrap the rapidly.
- Page 12 Fig. Suspension bracket for ceilings greater than ft. (6,1 m) - typical ) Suspension angle iron for attachment to joist. ) 7 in - x in bolt ) Welded angle iron to form base (locally fabricated) ) ...
- Page 13 Reel Packages Hose reel models -B, -B, and -B are included in the reel packages listed below. Reel package Hose reel Inlet components Outlet components model (bare) ° union Connecting hose Bushing Delivery hose Air coupler Air connector Hose stop -A -B -...
-
Page 14: Troubleshooting Chart
Troubleshooting chart Indications Possible problems Solution Reel does not latch. Spring () broken or not attached to latch Replace or secure spring (). pawl () Reel does not retract. Power spring broken. Replace power spring assembly (). ) Reel retracts partially. . - Page 15 Fig. IPB Heavy-duty hose reels - exploded view Apply thread sealant to male threads of ° unions. Note: Torque nut () from to ft.lbf (57 - 65 Nm). ) Repair kit low pressure swivel repair. ) Repair kit ...
- Page 16 Parts list Item Description Part no. Model Qty. Item Description Part no. Model Qty. Swivel assembly, low-pressure -B Screw, - x Stud, swivel -B Sleeve, pawl spring ) O-ring, in ID x in OD...
- Page 17 This page intentionally left blank. ...
- Page 18 This page intentionally left blank. ...
- Page 19 This page intentionally left blank. ...
- Page 20 ® Alemite, LLC is a registered trademark. The contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless prior written permission is granted. Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be accepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein.