Johnson Controls S300 Series Hardware Installation Manual
  1. Manuals
  2. Brands
  3. Johnson Controls Manuals
  4. Control Unit
  5. S300 Series
  6. Hardware installation manual

Johnson Controls S300 Series Hardware Installation Manual

Interface control for access and security devices
Hide thumbs Also See for S300 Series:
Table of Contents

Advertisement

Quick Links

S300
Series
S300-DIN-RDR2SA
Hardware Installation Manual
August, 2007
24-10239-472 Revision A

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the S300 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Johnson Controls S300 Series

Summary of Contents for Johnson Controls S300 Series

  • Page 1 S300 Series S300-DIN-RDR2SA Hardware Installation Manual August, 2007 24-10239-472 Revision A...
  • Page 2 All Rights Reserved (805) 522-5555 www.johnsoncontrols.com No part of this document may be reproduced without the prior permission of Johnson Controls, Inc. These instructions are supplemental. Often they are supplemental to other manufacturer’s documentation. Never discard other manufacturer’s documentation. Publications from Johnson...
  • Page 3 If this document is translated from the original English version by Johnson Controls, Inc., all reasonable endeavors will be used to ensure the accuracy of translation. Johnson Controls, Inc. shall not be liable for any translation errors contained herein or for incidental or consequential damages in connection with the furnishing or use of this translated material.
  • Page 5 Two-door access control input/output interface, each door’s interface consisting of: Supervised door monitor switch input, normally open or normally closed, based on wired configuration 24-10239-472 Rev. A This document contains confidential and proprietary information of Johnson Controls, Inc. © 2007 Johnson Controls, Inc.

  • Page 6: Installation

    Check the purchase order against the packing slips to ensure the order is complete. If the contents of a container are damaged in any way, notify the carrier and your Johnson Controls representative immediately. Report any discrepancies to your Johnson Controls representative. Save the packing materials for possible return shipments.

  • Page 7: Tools Needed

    1. Fully extend the white clips located on the bottom of the module. 2. Hook the module on top of the rail. 3. Push in the clips. 24-10239-472 Rev. A This document contains confidential and proprietary information of Johnson Controls, Inc. © 2007 Johnson Controls, Inc.

  • Page 8: Flat Surface Mounting

    See the following table for power requirements. Parameter Value Input voltage +12 to 24VDC, 16 o 24VAC Input current 1A at 24V, 2A at 12V Power 24-10239-472 Rev. A This document contains confidential and proprietary information of Johnson Controls, Inc. © 2007 Johnson Controls, Inc.
  • Page 9 POWER RDR2S-A PANEL S300 BUS READER 2 READER 2 READER 2 STRIKE SHUNT READER 1 READER 1 READER 1 STRIKE SHUNT 24-10239-472 Rev. A This document contains confidential and proprietary information of Johnson Controls, Inc. © 2007 Johnson Controls, Inc.
  • Page 10 READER 2 POWER PANEL S300 BUS READER 2 READER 2 READER 2 READER 1 READER 1 READER 1 STRIKE SHUNT STRIKE SHUNT 24-10239-472 Rev. A This document contains confidential and proprietary information of Johnson Controls, Inc. © 2007 Johnson Controls, Inc.
  • Page 11 READER 2 POWER PANEL S300 BUS READER 2 READER 2 READER 2 READER 1 READER 1 READER 1 STRIKE SHUNT STRIKE SHUNT 24-10239-472 Rev. A This document contains confidential and proprietary information of Johnson Controls, Inc. © 2007 Johnson Controls, Inc.
  • Page 12 READER 2 POWER PANEL S300 BUS READER 2 READER 2 READER 2 READER 1 READER 1 READER 1 STRIKE SHUNT STRIKE SHUNT 24-10239-472 Rev. A This document contains confidential and proprietary information of Johnson Controls, Inc. © 2007 Johnson Controls, Inc.

  • Page 13: Wiegand Input

    COM is required for 2-state operation. For wiring details see “Wiring Input Devices” on page 13. 24-10239-472 Rev. A This document contains confidential and proprietary information of Johnson Controls, Inc. © 2007 Johnson Controls, Inc.
  • Page 14 – 250mA at 12VDC is provided for each reader. Positive Temperature Coefficient) – There is a 750mA PTC ( re-settable Protection fuse. 24-10239-472 Rev. A This document contains confidential and proprietary information of Johnson Controls, Inc. © 2007 Johnson Controls, Inc.

  • Page 15: Cable Requirements

    42V CAUTION or Magnetic door locks without EMI suppression. 24-10239-472 Rev. A This document contains confidential and proprietary information of Johnson Controls, Inc. © 2007 Johnson Controls, Inc.

  • Page 16: Power Supply

    1st RDR2S-A 2nd RDR2S-A 2nd RDR2S-A 3rd RDR2S-A 3rd RDR2S-A RDR2S-A RS-485 cable connecting to S300 bus 24-10239-472 Rev. A This document contains confidential and proprietary information of Johnson Controls, Inc. © 2007 Johnson Controls, Inc.
  • Page 17 RDR2S-A in the enclosure, and programmed in the controller. Use the PANEL/TAMP connector for this function. 24-10239-472 Rev. A This document contains confidential and proprietary information of Johnson Controls, Inc. © 2007 Johnson Controls, Inc.
  • Page 18 150-2000 Ohms, 1%, 1/4W. The recommended resistor is 1200 Ohms. Ground Every metal DIN enclosure in a Johnson Controls installation must have its chassis bonded to a verified electrical ground (earth). Conduit ground, cold water pipes, unbrazed joints or dissimilar metals are unacceptable in the path of either building or supplemental ground.

  • Page 19: Setup And Adjustments

    The RDR2S-A modules follow the same rules as other terminated devices. See the following figure to determine the appropriate EOL setting for each RDR2S-A module in your network. 24-10239-472 Rev. A This document contains confidential and proprietary information of Johnson Controls, Inc. © 2007 Johnson Controls, Inc.

  • Page 20: Address Switches

    12/24 VDC supply power to the RDR2S-A and wait for the Power LED to go off. Changes will not take effect until after the power is restored. 24-10239-472 Rev. A This document contains confidential and proprietary information of Johnson Controls, Inc. © 2007 Johnson Controls, Inc.
  • Page 21 Table 1: Settings of the RDR2S-A Address Switches DIP Switch Number Label on the Module Hardware Wiegand Module No. RS485 See page 15 page 9 24-10239-472 Rev. A This document contains confidential and proprietary information of Johnson Controls, Inc. © 2007 Johnson Controls, Inc.
  • Page 22 When calibrating the 4-state auxiliary input, ensure that the switch is in the inactive state (not in the “request to exit” state). READER 1 24-10239-472 Rev. A This document contains confidential and proprietary information of Johnson Controls, Inc. © 2007 Johnson Controls, Inc.
  • Page 23 Spare Input 3 Configuration can be 2-state or 4-state. Input Terminal 2 READER 2 Spare Input 4 Configuration can be 2-state or 4-state. 24-10239-472 Rev. A This document contains confidential and proprietary information of Johnson Controls, Inc. © 2007 Johnson Controls, Inc.
  • Page 24 READER 2 inactive state (not in the “request to exit” state). Wire this input normally open. 24-10239-472 Rev. A This document contains confidential and proprietary information of Johnson Controls, Inc. © 2007 Johnson Controls, Inc.
  • Page 25 READER 1 Reader 1 READER 1 SHUNT Shunt Output Output is set every time an access grant or request to exit occurs. 24-10239-472 Rev. A This document contains confidential and proprietary information of Johnson Controls, Inc. © 2007 Johnson Controls, Inc.
  • Page 26 Output is an open collector that switches Output is an open collector that switches READER 1 to ground. to ground. 24-10239-472 Rev. A This document contains confidential and proprietary information of Johnson Controls, Inc. © 2007 Johnson Controls, Inc.
  • Page 27 See “General Input Wiring” on page 14 for reference. 24-10239-472 Rev. A This document contains confidential and proprietary information of Johnson Controls, Inc. © 2007 Johnson Controls, Inc.

  • Page 28: Specifications

    Transmit (XMIT): Blinks when a character is transmitted to the controller’s S300 bus. Receive (RCV): Blinks when a character is received from the controller’s S300 bus. 24-10239-472 Rev. A This document contains confidential and proprietary information of Johnson Controls, Inc. © 2007 Johnson Controls, Inc.

  • Page 29: Routine Maintenance

    Generic replacement terminal blocks can be ordered if lost. For more information on the parts listed, refer to the applicable catalog page. Fuses The RDR2S-A has no replaceable fuses. 24-10239-472 Rev. A This document contains confidential and proprietary information of Johnson Controls, Inc. © 2007 Johnson Controls, Inc.

This manual is also suitable for:

S300-din-rdr2sa

Table of Contents