Amplifier Back Panel - Nuvo Concerto NV-I8DMS User Manual

Concerto

Amplifier Back Panel

VARIABLE
OUTPUT
OUTPUT POWER
TIP=L
20W/6OHM X2
RING=R
FIXED
OUTPUT
ZONE 1 ZONE 2
1 2 3 4 5
L L
R R
1 2 3 4 5
SOURCE INPUTS
4
3
1 2
1. Variable Lineouts:
2. Fixed Lineouts:
3. Source Inputs:
4. Speaker Output:
5. Source Link:
6. Source Status Inputs:
7. Zone Trigger Outputs:
8. IR Emitter Outputs:
9. SYS. ON:
10. EXT. MUTE:
11. Network Input:
12. Digital Link:
13. RS232:
14. AC:
VARIABLE VARIABLE
OUTPUT OUTPUT
OUTPUT POWER
OUTPUT POWER
TIP=L TIP=L 20W/6OHM X2
20W/6OHM X2
RING=R RING=R
FIXED FIXED
OUTPUT OUTPUT
ZONE 3
1 2
6
CONNECT TO
NV-I8X
L
USE NV-SLC1
CABLE
R
4 5
6
SOURCE STATUS INPUTS
SOURCE LINK
5
6
These preamp lineouts are used for sending an audio signal to an external power
amplifier. This is useful for large areas that require additional pairs of speakers. Use
the variable output when you want the additional amplifier to be controlled by the
zone's Display Pad.
These preamp lineouts are used for sending an audio signal to an external power
amplifier when additional speakers are needed. This output is constant, so an amplifi-
er connected to it will not change volume with that zone's Display Pad.
The Concerto will accept up to six audio sources. These are connected to the Concerto
amplifier with standard stereo RCA cables.
Six of the Concerto's eight zones are amplified. These outputs accept 16-gage, two-con-
ductor speaker wire and provide 40 watts per channel of power.
This connection is used in conjunction with the Concerto Expander System to create
16 total zones. The source link cable is supplied with the Expander System.
These optional inputs can be used to monitor source power status. This is useful when
using a macro string of commands to prevent turning off a piece of equipment that is
already on and vice versa.
These 12-volt outputs can be used to trigger an external device, such as an auxiliary
power amplifier, for use in a specific zone.
IR signals received from the keypads are passed through the IR outputs to the source
equipment using the supplied IR emitters. Outputs 1-6 are routed to the corresponding
sources, and the SUM outputs 1 and 2 are common and will pass all IR signals.
This is a constant 12-volt output for turning on external equipment.
This input is designed to temporarily mute any audio playing through the system
when the doorbell or phone rings. This works in conjunction with the NuVo NV-MI1
mute interface accessory.
This RJ-45 connection is the input for all zone information coming from the Concerto
Display Pads. The connection is made using the Network Cable supplied with the package.
This connection is used in conjunction with the Concerto Expander System to create
16 total zones. The Digital Link cable is supplied with the Expander System.
The bidirectional RS232 is a serial communication port that allows the Concerto
System to be controlled by an external home automation device.
A detachable power cord connects the system to an external AC power supply.
VARIABLE VARIABLE
OUTPUT OUTPUT
OUTPUT POWER
OUTPUT POWER
20W/6OHM X2
TIP=L TIP=L
20W/6OHM X2
RING=R RING=R
FIXED FIXED
OUTPUT OUTPUT
ZONE 4 ZONE 5
3 4
1 2 3 1
6
5 6 7 8 4
ZONE TRIGGER OUTPUTS
7
8
VARIABLE VARIABLE
OUTPUT
OUTPUT
OUTPUT POWER
TIP=L TIP=L
20W/6OHM X2
RING=R
RING=R
FIXED FIXED
OUTPUT OUTPUT
ZONE 6 ZONE 6 ZONE 7&8 PROGRAM
2 3 SUM1 SYS ON
CONNECT TO CONNECT TO
NV-I8EZP1
USE NV-NC1 USE NV-SLC1
CABLE
5 6 SUM2
EXT. MUTE
EMITTER OUTPUTS SYSTEM NETWORK DIGITAL LINK
9 10 11
8
RS-232
USE CNLY WITH 250V FUSE
MODEL NV-I8DM
SIX SOURCE EIGHT ZONE
AUDIO DISTRIBUTION SYSTEM
NV-I8X
120V 60Hz 500W FUSE:T5 A
NuVo Technologies Cincinnati Ohio USA
www.nuvotechnologies.com
CABLE
CONFORMS TO
R
UL STD.6500
C US CERTIFIED TO
CAN/CSA STD.E60065
3033118
13
14
12