Makita DVC867L Instruction Manual page 20

NOTE: When performing two or more tool registration for the cleaner,
finish the tool registration one by one.
Starting the wireless activation function
NOTE: Finish the tool registration for the cleaner for wireless
activation.
NOTE: Always place the cleaner so that you can see the status of the
wireless activation lamp. NOTE: Refer to the instruction manual of the
tool, too.
After registering a tool to the cleaner, the cleaner will automatically runs
along with the switch operation of the tool.
1. Install the wireless units to the cleaner and the tool, respectively.
2. Install the batteries to the cleaner and the tool.
Connect the hose of the cleaner with the tool. ► Fig.27
3.
Set the stand-by switch on the cleaner to "AUTO". ► Fig.28:
4.
Stand-by switch
5. Push the wireless activation button on the tool briefly. The wireless
activation lamp will blink in blue.
► Fig.29:
1. Wireless activation button 2. Wireless activation lamp
6. Pull the switch trigger of the tool. Check if the cleaner runs while
the switch trigger on the tool is being pulled.
CAUTION:
Always check if the wireless
activation function works before starting a work
with the tool.
To stop the wireless activation, push the wireless activation button on
the tool, or set the stand-by switch on the cleaner to "I" or "O".
NOTE: The wireless activation lamp on the tool will stop blinking in
blue when there is no operation for 2 hours. In this case, set the
stand-by switch on the cleaner to "AUTO" and press the wireless
activation button on the tool again.
NOTE: The cleaner starts/stops with a delay. There is a time lag when
the cleaner detects a switch operation of the tool.
NOTE: The transmission distance of the wireless unit may vary
depending on the location and surrounding circumstances.
NOTE: When two or more tools are registered to one cleaner, the
cleaner may start running even if you don't pull the switch trigger
because other user is using the wireless activation function.
Cancelling tool registration for the cleaner
Perform the following procedure when cancelling the tool registration for
the cleaner.
1. Install the wireless units to the cleaner and the tool, respectively.
2. Install the batteries to the cleaner and the tool.
Set the stand-by switch on the cleaner to "AUTO". ► Fig.30:
3.
Stand-by switch
4. Press the wireless activation button on the cleaner for 6 seconds.
The wireless activation lamp blinks in green and then become red.
After that, press the wireless activation button on the tool in the
same way.
► Fig.31:
1. Wireless activation button 2. Wireless activation lamp
If the cancellation is performed
successfully, the wireless activation
lamps will light up in red for 2
seconds and start blinking in blue.
1.
You can erase all tool registrations
from the cleaner as follows.
► Fig.32:
1.
20 ENGLISH
NOTE: The wireless activation
lamps finish blinking in red after 20
seconds elapsed. Press the
wireless activation button on the
tool while the wireless activation
lamp on the cleaner is blinking. If
the wireless activation lamp does
not blink in red, push the wireless
activation button briefly and hold it
down again.
Erasing all tool
registrations
1. Stand-by switch 2.
Wireless activation button
3. Wireless activation
lamp
1. Install the wireless unit to the
cleaner.
2. Install the batteries to the
cleaner.
3. Set the stand-by switch to
"AUTO".
4. Hold down the wireless
activation button for about 6
seconds until the wireless
activation lamp blinks in red
(about twice per one second).
5. When the wireless activation
lamp starts blinking in red,
release your finger from the
wireless activation button.
Thereafter, hold down the
wireless activation button again
for about 6 seconds.
6. When the wireless activation
lamp starts blinking fast (about
5 times per one second) in red,
release your finger from the
wireless activation button.
When the wireless activation
lamp lights up in red and later
lights off, all tool registrations
are erased.
NOTE: If the wireless activation
lamp does not blink in red, press
the wireless activation button briefly
and try again.