Makita DVC867L Instruction Manual page 19

NOTICE:
Be sure to refer to the instruction manual of the tool
when using the cleaner with wireless activation function.
NOTICE:
Do not disassemble or tamper with the wireless unit.
NOTICE:
To prevent dust coming into the slot of the wireless
unit, always close the lid securely during operation and storage.
NOTICE:
Do not remove the wireless unit while the power is
being supplied. Doing so may cause a malfunction of the wireless
unit.
NOTICE:
Do not press the wireless activation button too hard
and/or press the button with an object with a sharp edge.
NOTE: Wireless activation needs Makita tools equipped with the
wireless unit.
NOTE: Prior to the initial use of the wireless activation function with
each tool, the tool registration is required. Once the registration is
finished with the tool, the re-registration is not required unless it is
cancelled.
NOTE: Before registration, be sure that the wireless unit is properly
inserted.
NOTE: One wireless unit can register up to 10 links with other wireless
units. If more than 10 other wireless units are registered to one
wireless unit, the one registered earliest will be cancelled
automatically.
NOTE: The position of the wireless activation button varies depending
on the tool.
NOTE: The cleaner also starts by pressing the power button when the
stand-by switch is set to "AUTO". However the power button will not
actuate when the wireless activation function is used.
Installing the wireless unit
CAUTION:
Place the cleaner on a flat and
stable surface when installing the wireless unit.
NOTICE:
Clean the dust and dirt on the cleaner before installing
the wireless unit. Dust or dirt may cause malfunction if it comes into
the slot of the wireless unit.
NOTICE:
To prevent the malfunction caused by static, touch a
static discharging material, such as a metallic part, before
picking up the wireless unit.
NOTICE:
When installing the wireless unit, always be sure that
the wireless unit is inserted in the correct direction and the lid is
completely closed.
Open the lid on the cleaner as shown in the figure. ►
1.
Fig.22: 1. Lid
2. Insert the wireless unit to the slot and then close the lid.
When inserting the wireless unit, align the projections with the recessed
portions on the slot.
► Fig.23:
1. Wireless unit 2. Projection 3. Lid
4. Recessed portion
When removing the wireless unit, open the lid slowly. The hooks on the
back of the lid will lift the wireless unit as you pull up the lid.
► Fig.24:
1. Wireless unit 2. Hook 3. Lid
After removing the wireless unit, keep it in the supplied case or a static-
free container.
If you wish to activate the cleaner
along with the switch operation of
the tool, finish the tool registration
beforehand.
► Fig.26:
If the cleaner and the tool are linked
successfully, the wireless activation
lamps will light up in green for 2
seconds and start blinking in blue.
19 ENGLISH
NOTICE:
Always use the hooks
on the back of the lid when
removing the wireless unit. If the
hooks do not catch the wireless
unit, close the lid completely and
open it slowly again.
Tool registration for the
cleaner
NOTE: A Makita tool supporting the
wireless activation function is
required for the tool registration.
NOTE: Finish installing the wireless
unit to the tool before starting the
tool registration.
NOTE: During the tool registration,
do not pull the switch trigger on the
tool or turn on the power switch on
the cleaner.
NOTE: Refer to the instruction
manual of the tool, too.
1. Install the wireless units to the
cleaner and the tool,
respectively.
2. Install the batteries to the
cleaner and the tool.
3. Set the stand-by switch on the
cleaner to "AUTO". ► Fig.25:
1. Stand-by switch
4. Press the wireless activation
button on the cleaner for 3
seconds until the wireless
activation lamp blinks in green.
And then press the wireless
activation button on the tool in
the same way.
1. Wireless activation
button 2. Wireless
activation lamp
NOTE: The wireless activation
lamps finish blinking in green after
20 seconds elapsed. Press the
wireless activation button on the
tool while the wireless activation
lamp on the cleaner is blinking. If
the wireless activation lamp does
not blink in green, push the wireless
activation button briefly and hold it
down again.