Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Stern Pinball WRESTLEMANIA WWE PRO
Summary of Contents for Stern Pinball WRESTLEMANIA WWE PRO
- Page 1 PINBALL MACHINE SERVICE AND OPERATION MANUAL WWE PRO WWE PRO #500-55G1-00 Games configured forNorth America operate on 60 cycle electricity only. These games will not operate in countries MANUAL #780-50G1-00 with 50 cycle electricity (Europe UK, Australia).
-
Page 2: Table Of Contents
TABLE OF CONTENTS GAME SOFTWARE UPDATE Setup and Moving ........3 Keep your game up to date! The latest Stern game software is always available at www.sternpinball.com. Stern games First-time Setup ............3 show the current version number when starting up. Transporting the Game .......... -
Page 3: Setup And Moving
AT LEAST TWO (2) PEOPLE ARE RE- QUIRED TO MOVE AND MANEUVER TOOLS REQUIRED THE GAME. USE PROPER MOVING Your brand new Stern Pinball Machine is EQUIPMENT AND EXTREME CARE carefully packed for safety and security. • 5/8” Socket Wrench WHILE HANDLING. - Page 4 SETUP AND MOVING FIRST-TIME SETUP CONTINUED 16. Locate the factory keys, either on the 21. Store the backbox keys, if desired, 19. Reach into the game and remove the shooter rod or taped to the playfield on the metal hook located in the coin retaining clip at the rear of the cash glass.
- Page 5 SETUP AND MOVING FIRST-TIME SETUP CONTINUED 30. If pinballs were already installed into the lower ball trough, remove them before lifting the playfield. 31. Raise the playfield and rest it against the backbox. 32. Grasp the lower arch between the flippers, and firmly but gently pull directly up to raise the playfield 8-12 inches.
-
Page 6: Transporting The Game
SETUP AND MOVING 1.2 TRANSPORTING THE GAME CAUTION When transporting the game, such as in the back of a truck or with a hand truck, the game’s backbox must be secured to prevent damage to the side rails. NEVER TRANSPORT THE GAME IN A MOVING VEHICLE WITH THE BACKBOX RAISED! TWO PEOPLE ARE REQUIRED 1. -
Page 7: Spike Pinball Platform Overview
9V node bus power is disabled to all playfield components until the switch is closed. A Stern Pinball machine based on the SPIKE system will have at least two nodes networked together with the SPIKE node bus, 1.7 SPIKE NODE ADDRESSES a custom industrial pinball control bus that is designed around industry standards and optimized for the pinball environment. -
Page 8: Spike Node Programming
SPIKE PINBALL PLATFORM OVERVIEW FLASHERS SPIKE games treat flashers the same as single LEDs that draw more power. Flashers are controlled from the same circuits that power regular lights. DRIVERS Figure 1.7.1. SPIKE node addresses for nodes with 3-position DIP A driver is a circuit that controls a high power-device such as a switches. -
Page 9: Light, Switch, And Driver Reference
LIGHT, SWITCH, AND DRIVER REFERENCE 3. LIGHT, SWITCH, AND DRIVER REFERENCE Playfield front TROUGH SERIAL OPTO RECEIVER CN14 NODE 9A 520-5345-00 BACKBOX NODE 8 CN23 SD CARD CN24 CN25 OFF OFF OFF OFF BATTERY LINE 520-6936-00A RESET SPIKE CPU DIP S2 SPIKE NODE BUS AMPLIFIED AUDIO CN22... -
Page 10: Driver Reference
LIGHT, SWITCH, AND DRIVER REFERENCE 3.1 DRIVER REFERENCE PLAYFIELD TOP PLAYFIELD BOTTOM Figure 3.1.1. Playfield bottom component view, playfield shown in Figure 3.1.2. Playfield top component view service position. Rear of game is at bottom of figure. WWE and related marks 02/12/15 WWE PRO MANUAL #780-50G1-00 ™... -
Page 11: Lighting Reference
LIGHT, SWITCH, AND DRIVER REFERENCE DRIVER REFERENCE TABLE ID Name Node Con- Ret. Ret. Wire Volt- V+ Pin V+ Color Location Type Address Part Number nector Trough ORG-GRY GRY-ORG Playfield Coil - 27-1500 8-DR-5 090-5004-ND Auto Plunger ORG-WHT 48V GRY-ORG Playfield Coil - 23-800 8-DR-4 090-5001-ND... - Page 12 LIGHT, SWITCH, AND DRIVER REFERENCE LIGHTING REFERENCE 48-50 52-54 42-44 57-59 29-31 29-31 42-44 57-59 52-54 48-50 Figure 3.2.3. Playfield top view Figure 3.2.2. Playfield bottom, shown in upright service position. WWE and related marks 02/12/15 WWE PRO MANUAL #780-50G1-00 ™...
- Page 13 LIGHT, SWITCH, AND DRIVER REFERENCE LIGHTING REFERENCE Figure 3.2.5. Playfield back panel lighting locations. LEGEND For detailed wire color, node board, pin- out, and lighting component information, Multi, General Illumination locate the node that the light in question is connected to and refer to the node Single, Low-Current board detail section.
- Page 14 LIGHT, SWITCH, AND DRIVER REFERENCE LIGHTING REFERENCE CONTINUED Name Node Node Conn. Ret. Ret. Wire Src. Src. Location Type Light Address Part Number Ext. Wire Color Right Orbit Arrow(Green) 9 CN16 GRN-ORG 1 Playfield Feature RGB 9-LP-11 520-5333-00 Right Orbit Arrow(Blue) CN16 BLU-ORG Playfield...
-
Page 15: Switch Reference
LIGHT, SWITCH, AND DRIVER REFERENCE 3.3 SWITCH REFERENCE Name Node Node Conn. Input Input Ground Location Type Address Part Number Wire Wire Left Return Lane LGN-YEL BLK-RED Playfield Rollover 11-SW-0 500-9935-04 Right Return Lane PNK-BLK 10 BLK-GRY Playfield Rollover 11-SW-8 500-9935-04 Left Outlane LGN-BLU 10... - Page 16 LIGHT, SWITCH, AND DRIVER REFERENCE SWITCH REFERENCE Figure 3.3.2. Switch locations, playfield top view Figure 3.3.3. Switch locations, playfield bottom, shown in upright service position. WWE and related marks 02/12/15 WWE PRO MANUAL #780-50G1-00 ™ & © 2014 WWE. All Rights Reserved.
- Page 17 LIGHT, SWITCH, AND DRIVER REFERENCE SWITCH REFERENCE CONTINUED Name Node Node Conn. Input Input Ground Location Type Address Part Number Wire Wire Ladder exit TAN-VIO BLK-ORG Playfield Rollover 11-SW-22 180-5209-00 Left ring exit CN15 11 LGN-BRN 14 BLK-VIO Playfield Rollover 10-SW-13 180-5209-00 Left Ramp Exit...
- Page 18 LIGHT, SWITCH, AND DRIVER REFERENCE SWITCH REFERENCE TABLE CONTINUED Name Node Node Conn. Input Input Ground Location Type Address Part Number Wire Wire DIP 1 CPU Node 0-SW-0 C10 Service Plus CN25 3 LGN-VIO Coin Door 0-SW-10 180-5192-02 C11 Service Minus CN25 2 LGN-BLU 6 Coin Door...
-
Page 19: Electronic Pinouts And Schematics
ELECTRONIC PINOUTS AND SCHEMATICS 4. ELECTRONIC PINOUTS AND SCHEMATICS 4.1 SPIKE CPU NODE 0 520-6936-00 CONNECTORS CN23 Connector Type Description SD CARD 5-Pin .156” Header Backbox 2-channel amplified speaker out CN24 CN25 BATTERY RJ45 SPIKE node bus - to cabinet node N1 2-Pin .156”... - Page 20 ELECTRONIC PINOUTS AND SCHEMATICS SPIKE CPU NODE 0 CONTINUED STATUS LEDS Name Color Description +48V Supply In ON: Main system power is connected, OFF: No 48V system power. Check power supply connections, cables, and fuses. +24V Audio Power ON: Audio power supply is good, OFF: Audio power supply off, call tech support. +9V Node Bus Power ON: Node bus power supply is good, OFF: Node bus power supply bad, call tech support.
-
Page 21: Cabinet Node 1
ELECTRONIC PINOUTS AND SCHEMATICS 4.2 CABINET NODE 1 520-5319-00 SWITCH MAPPING The cabinet node is hardcoded for address 1, so no address DIP switch setting is necessary. The coin door service switches use the cabinet board as a pass-through connector to the CPU node via CN10 and CN12. See the coin door service switch wiring diagram in the CPU Node section. - Page 22 ELECTRONIC PINOUTS AND SCHEMATICS CABINET NODE 1 CONTINUED CABINET NODE PINOUT Type Pin Description Wire Color .100" 6-Pin Coin Enable/DBA Inhibit (-) Opt. Header .156" 5-Pin Shaker Motor (-) Coin Enable/DBA Inhibit (+) Opt. Dollar Bill Header Shaker Motor (-) Opt.
-
Page 23: Lower Playfield 48V 8-Driver Node 8
ELECTRONIC PINOUTS AND SCHEMATICS 4.3 LOWER PLAYFIELD 48V 8-DRIVER NODE 8 520-6935-00 Figure 4.2.2. Lower playfield 48V 8-driver node (Node 8)playfield location Flipper button switches 10 11 located on cabinet GREEN ORANGE BLACK NEUTRAL CN13 520-6935-00B 8-Driver Node GREEN ORANGE BLACK NEUTRAL Figure 4.2.3. - Page 24 ELECTRONIC PINOUTS AND SCHEMATICS LOWER PLAYFIELD 48V 8-DRIVER NODE 8 NODE ADDRESS SETTING DIP SW1 Switches and lights designed Node Ext 8a are connected via serial bus on CN14 and Node 8 controlled by Node 8. SWITCHES CONNECTED TO NODE 8 Name Node Node Con-...
-
Page 25: Lower Playfield Serial Led (Node 8A)
ELECTRONIC PINOUTS AND SCHEMATICS Intercont. title CN14 Playfield Flash White 8a-LP-32 199-6950-00 Heavy weight title CN14 Playfield Flash White 8a-LP-31 199-6950-00 DRIVERS CONNECTED TO NODE 8 Description Node Connector Return Return 48V Power Location Type Address Part Number Wire Power Color Trough ORG-GRY... -
Page 26: Mid Playfield 4-Driver 48V Node 9
ELECTRONIC PINOUTS AND SCHEMATICS 4.5 MID PLAYFIELD 4-DRIVER 48V NODE 9 48-50 52-54 52-54 48-50 Figure 4.5.1. Mid Playfield 4-driver 48V Node (Node 9) playfield location and relevant lighting, switches, and drivers. WWE and related marks 02/12/15 WWE PRO MANUAL #780-50G1-00 ™... - Page 27 ELECTRONIC PINOUTS AND SCHEMATICS MID PLAYFIELD 4-DRIVER 48V NODE (N9, N9A) CONTINUED 520-5329-00 Node 9 controls the trough opto serial board, Node N9a. GREEN ORANGE BLACK NEUTRAL NODE ADDRESS SETTING DIP SW1 520-5329-00E Node 9 4 Coil NODE Figure 4.5.2. Mid Playfield 4-driver 48V Node (Node 9)connector detail. SWITCH MAPPING Name Node Node...
-
Page 28: Trough Serial Opto Receiver
ELECTRONIC PINOUTS AND SCHEMATICS Left orbit arrow(Grn) 9 CN16 GRN-BRN Playfield Feature 9-LP-7 520-5333-00 Left orbit arrow(Blu) 9 CN16 BLU-BRN Playfield Feature 9-LP-8 520-5333-00 Left orbit (Ref) CN16 ORG-BRN 1 Playfield Feature White 9-LP-9 520-5307-00 Right orbit ar- CN16 RED-ORG Playfield Feature 9-LP-10 520-5333-00... -
Page 29: Upper Mini Playfield 4-Driver 48V Node 10
ELECTRONIC PINOUTS AND SCHEMATICS 4.8 UPPER MINI PLAYFIELD 4-DRIVER 48V NODE 10 520-5329-00 Figure 4.8.1. Back panel detail for Upper Mini Playfield 4-driver 48V Node 10 connections. 52-54 Figure 4.8.2. Upper Mini Playfield 4-driver 48V node 10 playfield location and relevant lighting, switches, and drivers. WWE and related marks 02/12/15 WWE PRO MANUAL #780-50G1-00... - Page 30 ELECTRONIC PINOUTS AND SCHEMATICS UPPER MINI PLAYFIELD 4-DRIVER 48V NODE 10 CONTINUED NODE ADDRESS SETTING GREEN ORANGE BLACK NEUTRAL DIP SW1 520-5329-00E Node 11 4 Coil NODE Figure 4.8.3. Upper mini playfield 4-drive 48V node connector detail, 520-5329-00. SWITCHES CONNECTED TO NODE 10 Name Con- Input...
-
Page 31: Upper Playfield Lighting And Switch Node 11
ELECTRONIC PINOUTS AND SCHEMATICS UPPER MINI PLAYFIELD 4-DRIVER 48V NODE 10 CONTINUED DRIVERS CONNECTED TO NODE 10 Description Connec- Return Return 48V Pow- Location Type Address Part Number Wire Power er Color Ramp Control Gate(RT) CN11 BLU-RED 4 GRY-BRN Back Panel Coil - 32-1250 10-DR-3 090-5060-01-ND Left Slingshot(Ring) YEL-BLK... -
Page 32: Upper Mini Playfield Led Board
ELECTRONIC PINOUTS AND SCHEMATICS NODE ADDRESS SETTING BLACK ORANGE NEUTRAL GREEN DIP SW1 Node 11 NODE BUS AND SERIAL CON- 520-5322-00H 32 SW / 32 LED NODE NECTIONS CN10 CN1A Connector Destination CN10 (RJ45) N10- Upper Mini Playfield 4-Driver 48V Node GREEN ORANGE BLACK... - Page 33 ELECTRONIC PINOUTS AND SCHEMATICS UPPER PLAYFIELD LIGHTING AND SWITCH NODE 11 CONTINUED 48-50 52-54 42-44 57-59 29-31 29-31 42-44 57-59 52-54 48-50 Figure 4.10.3. Upper playfield lighting and switch node 11 lighting, drivers, and switches. WWE and related marks 02/12/15 WWE PRO MANUAL #780-50G1-00 ™...
-
Page 34: Opto Amplifier Wiring
ELECTRONIC PINOUTS AND SCHEMATICS 4.11 OPTO AMPLIFIER WIRING 4.13 BACKBOX INTERCONNECT BLOCK DIAGRAM 520-5239-01 INTERCONNECT BLOCK DIAGRAM There are two opto amplifiers in WWE. One is connected to the pair of optos on top of the pop bumpers, the other is on the rear orbit shots on the upper playfield. -
Page 35: Power Distribution Board
ELECTRONIC PINOUTS AND SCHEMATICS 4.15 POWER PLUG WIRING 4.14 POWER DISTRIBUTION BOARD 520-5343-00 CAUTION TO MAINTAIN SAFETY, GROUND WIRE FROM LINE FILTER IS TO BE MOUNTED FIRST ON GROUNDING STUD AND SECURED WITH NUT. ALL OTHER GROUNDS MAY THEN BE ATTACHED TO GROUNDING STUD. -
Page 36: Parts Reference
PARTS REFERENCE 5. PARTS REFERENCE 5.1 PLAYFIELD TOP PARTS ID Part Number Description 545-5995-02 Playfield Arch Black 535-1069-00 Drop Target Ball Defelector 535-1137-00 Two Bank Defelector 516-0036-00 Bubble Level Prime Assy 511-7636-00 Shooter One Way Gate Assembly 260-5000-00 Steel Balls 1.0625 DIA 511-7603-00 Jet Bumper Assembly 516-0033-02... -
Page 37: Playfield Bottom Parts
PARTS REFERENCE 5.2 PLAYFIELD BOTTOM PARTS Part Number DescriptiOFF 500-9818-00 Auto Launch Assembly 500-9820-04 Ball Trough Assembly 500-6543-83-ND Left Flipper Assembly 500-6543-82-ND Right Flipper Assembly 500-9920-01 Slingshot assembly (26-1200) 500-7216-03 3-bank drop target assembly 515-6459-04-ND Pop bumper assembly 500-9934-01 Pop Bumper Switch 500-5329-03 Pivot Slide Bracket 535-5988-01... -
Page 38: Playfield Rubber Parts
PARTS REFERENCE 5.3 PLAYFIELD RUBBER PARTS RUBBER O-RINGS Qty Size Size Durometer Color Part Number (ID) (OD) 3/16" Black 545-5348-01 3/16" Black 545-5348-01-40 3/16" White 545-5348-51 5/16" Black 545-5348-02 5/16" Black 545-5348-02-40 5/16" White 545-5348-52 3/8" Black 545-5348-03 7/16" Black 545-5348-18 7/16"... -
Page 39: Rubber Size Chart
PARTS REFERENCE 5.6 LIGHTING COMPONENTS 5.4 RUBBER SIZE CHART Part Number Description 3-1/2” 077-5000-00 SOCKET STAPLE DOWN 2 LUGS REV A 077-5035-00 SCKT 3/LUG LNG SHELL 45ø BRKT 3” 077-5106-00 SOCKET REVERSE MT 9/32 2 LUG 89 2-3/4” 2-1/2” 077-5206-00 SCKT - POP BUMPER LAMP REV-A 077-5223-00 SOCKET 2 V/LUG SHORT REV A... -
Page 40: Playfield Spacers
PARTS REFERENCE 5.8 PLAYFIELD SPACERS Part Number Description 254-5000-01 SPACER .175 ID 3/8 OD "A" .500 B/G 254-5000-07 SPACER .175 ID 3/8 OD "A" .750 B/G 254-5000-09 SPACER .175 ID 3/8 OD "A" .250 B/G 254-5000-18 SPACER .175 ID 3/8 OD "A" .187 B/G 254-5000-19 SPACER .175 ID 3/8 OD "A"... -
Page 41: Backbox Parts
PARTS REFERENCE 5.10 BACKBOX PARTS 500-9902-G1 Figure 5.10.1. Backbox external assemblies and components Figure 5.10.3. Backbox internal assemblies and components EXTERNAL INTERNAL Part Number Description Part Number Description 830-52G1-00 Translite Art 520-6936-00 CPU Node Board 660-5038-02 Back Glass 520-5343-00 Power Distribution Board 545-5018-14 Plastic Extrusion 18-1/8"... -
Page 42: Speaker Panel Parts
PARTS REFERENCE 5.11 SPEAKER PANEL PARTS 5.12 CABINET DECALS 500-9854-G1 Figure 5.11.1. Speaker panel back Figure 5.11.2. Speaker panel front Part Number Description 515-9763-00 Speaker Panel 520-5052-15 Red LED Matrix Display 031-5004-02 Speaker 4 in 8 OHM 535-8081-01 Speaker Grill 4X4 Figure 5.12.1. -
Page 43: Cabinet Parts
501-5018-173 COIN DOOR 2-CHUTE NO EMBOSS 180-5160-01 SINGLE FLIPPER SWITCH 180-5160-00 FLIPPER SWITCH, DOUBLE 355-5038-00 DRAW LATCH, OVER CENTER CLAMP PARTS REFERENCE 545-5072-03 GRILL - SPEAKER / VENT 545-5072-02 GRILL - SPEAKER / VENT 031-5007-01 SPEAKER, CABINET 8" ROUND, 4 OHM SCRIPTION QTY. -
Page 44: Auto Launch Assembly
PARTS REFERENCE 5.14 AUTO LAUNCH ASSEMBLY 5.15 BALL TROUGH ASSEMBLY 500-9818-00 500-9820-00 ID Part Number Description 515-9689-00 MAIN BRKT: AUTO-PLUNGER ID Part Number Description 535-0728-00 KICKER ARM, AUTO-PLUNGER 515-7811-00 MAIN BRKT. BALL TROUGH 270-5001-00 RETAINING E-RING, 3/16" SHAFT OD 515-7812-00 COIL BRACKET, BALL TROUGH 545-5352-00 NYLINER, 3/16"... -
Page 45: 3-Bank Drop Target Assembly
PARTS REFERENCE 5.16 3-BANK DROP TARGET ASSEMBLY ITEM NO. PART NUMBER 545-6163-03 500-7216-03-G1 242-5091-00 266-5089-00 545-6305-00 237-5501-00 240-5102-00 269-5002-00 270-5002-00 266-5020-00 265-5003-02 535-9959-00 237-5602-00 237-6169-00 530-5757-00 545-5076-01 520-5252-03 090-5034-ND 515-7784-03 535-9996-03 535-9995-01 237-5985-00 545-6798-00 TITLE 3-BANK D ITEM Part Number Description 545-6163-03 LEDGE, 3-BANK DROP TARGET... -
Page 46: Pop Bumper Assembly
PARTS REFERENCE 5.17 POP BUMPER ASSEMBLY 516-6784-XX Part Number Description 515-6459-01L BUMPER/RING TOP ASSY, W/ LED 1 515-6459-04-ND BUMPER BOTTOM ASSY, NO DIODE Figure 5.17.2. 516-6784-XX Pop bumper assy major subassem- blies. ID Part Number Description 500-9934-01 POP BUMPER SWITCH ASSY-2 - LUG-LEFT 240-5005-00 6-32 NYLON STOP NUT 10 090-5044-ND COIL - 26-1200... -
Page 47: Flipper Assembly, Left
PARTS REFERENCE 5.18 FLIPPER ASSEMBLY, LEFT 5.19 FLIPPER ASSEMBLY, RIGHT 500-6543-02-ND 500-6543-12-ND Figure 5.18.1. Left flipper assembly 500-6543-02-ND bottom view. Figure 5.19.2. Right flipper assembly 500-6543-12-ND bottom view. ID Part Number Description ID Part Number Description 515-6617-01 FLIPPER BASE PLATE LEFT KIT W/ 515-6617-00 FLIPPER BASE PLATE RIGHT KIT W/ BRACKET MOUNTING HARDWARE... -
Page 48: Left Wwe Ramp Assembly
PARTS REFERENCE 5.20 LEFT WWE RAMP ASSEMBLY 5.22 RIGHT WWE RAMP ASSEMBLY 500-9886-00 500-9887-00 ITEM PART NUMBER DESCRIPTION QTY. LEFT RAMP WITH RAMP 510-7494-00 FLAP OPTO TRANSCEIVER ASSY, 500-6775-01 15" LEADS 830-7024-00 DUDES ADHESIVE FILM SCREW, #4-40 X 5/16 PRH 237-5882-00 SEMS ID Part Number... -
Page 49: Back Panel Assembly, Wwe Pro
PARTS REFERENCE 5.23 BACK PANEL ASSEMBLY, WWE PRO 500-9885-00 Item Part Number Description Item Part Number Description 525-9700-00 BACK PANEL, WWE PRO 240-5101-00 8-32 T-NUT 112-5034-08 DOUBLE LED, BAYONET BASE - WHITE 830-6947-13 BUTYRATE SET - 13 077-5000-00 SOCKET - STAPLED - 2 LUGS 077-5106-00 2-LUG STAND-UP REV. -
Page 50: Wwe Top Lanes Assembly
PARTS REFERENCE 5.24 WWE TOP LANES ASSEMBLY 500-9921-00 Part Number Description 511-7620-00 TOP LANES POST ASSEMBLY 550-5017-01 STARBURST TRIANGLE 254-5000-18 NYLON SPACER - BLACK - 3/8 OD X .175 ID X 3/16" 511-7606-00 TOP LANES LIGHT AND SWITCH ASSEM- 240-5005-00 6-32 NYLON STOP NUT Figure 5.24.1. -
Page 51: Wwe Top Lanes Lights And Switches
PARTS REFERENCE 5.27 WWE TOP LANES LIGHTS AND SWITCHES 511-7606-00 ITEM Item Part Number Description 535-1082-00 TOP LANES LIGHT AND SWITCH BRACK- 520-5307-00 PCB, SINGLE LED 180-5209-00 SUB MINIATURE SWITCH - SIM. ROLLER 232-5209-00 SCREW, 6-32 X 3/16" PPH SEMS 535-6539-00 SWITCH BODY PROTECT PLATE 237-5937-02... -
Page 52: Wwe Top Lanes Posts Assy
PARTS REFERENCE 5.30 WWE POP BUMPER FLASHER 5.29 WWE TOP LANES POSTS ASSY ASSEMBLY 511-7620-00 511-7627-00 ITEM NO. PART NUMBER Descrip 515-9796-00 TOP LANES SCREW, #6 X 237-5805-00 7/16 O.D. RUB 545-5348-17 BLAC 550-5052-01 MINI POST 535-1087-00 TOP LANES H 830-6947-09 BUTYRATE 550-5059-01... -
Page 53: Wwe Mini Playfield Assembly
PARTS REFERENCE 5.31 WWE MINI PLAYFIELD ASSEMBLY QTY. 500-9919-00 QTY. Figure 5.31.1. 500-9919-00 mini playfield assembly top view Figure 5.31.2. 500-9919-00 mini playfield assembly bottom view Item Part Number Description Item Part Number Description 830-51G1-01 MINI PLAYFIELD, WWE PRO 520-6951-00 WWE RING SWITCH / LED SERIAL BOARD 1 550-7366-00 WWE RING POST... -
Page 54: Wwe Ladder Light And Switch Assembly
PARTS REFERENCE 5.32 WWE LADDER LIGHT AND 5.34 WWE LADDER EXIT SWITCH SWITCH ASSEMBLY ASSEMBLY 511-7624-00 511-7609-00 ITEM PART NUMBER DESCRIPTION QTY. LADDER LIGHT AND SWITCH 535-1088-00 BRACKET PRO P/F ROLLOVER SWITCH - 180-5230-01 LITE 237-5937-02 SCREW, 2-56 X 1/2" HWH MS SWITCH BODY PROTECT 535-6539-00 PLATE... -
Page 55: Wwe Pop Bumper Playfield Assembly
PARTS REFERENCE 5.35 WWE POP BUMPER PLAYFIELD 5.36 WWE BALL GUIDE 04 ASSEMBLY ASSEMBLY 511-7572-04 511-7603-00 ITEM NO. PART NUMBER DESCRIPT 510-7511-00 POP BUMPER AS 550-5052-01 MINI POST - C 237-5809-00 SCREW, #6 X 1/ 500-6775-01 OPTO TRANSCEIVER A ID Part Number Description 550-5034-01 GROOVED JEWEL PLAS 535-1021-04 WWE BALL GUIDE - 04... -
Page 56: Wwe Ladder Assembly
PARTS REFERENCE 5.38 WWE LADDER ASSEMBLY 5.40 WWE STAND UP TARGET 3-BANK ASSEMBLY 500-9929-00 500-9923-00 ITEM PART NUMBER DESCRIPTION QTY. 510-7506-00 LADDER RIVET ASSEMBLY LADDER LIGHT AND SWITCH 511-7624-00 ASSEMBLY SCREW, 4-40 X 5/16" PFH U/C 237-6151-00 240-5303-00 4-40 NYLON LOCK NUT LADDER EXIT SWITCH 511-7609-00 ASSEMBLY... -
Page 57: Sling Shot Assemblies
PARTS REFERENCE 5.42 SLING SHOT ASSEMBLIES 5.43 ELECTRIC GATE, RAIL MOUNT 500-9924-XX, 500-9920-01 511-7637-XX ITEM PART NUMBER 515-5339-01 090-5044-ND 545-5031-00 535-5203-03 232-5301-00 180-5231-00 535-5045-00 500-9924-00 500-9924-01 237-5976-04 "RIGHT" "LEFT" 515-5340-01 270-5002-00 515-5338-00 RING 266-5020-00 Figure 5.42.5. Sling shot core assembly explosion. 511-7637-00 RING "LEFT"... -
Page 58: Warranty
Take great caution when serving any STERN PINBALL INC LIMITED WARRANTY electrical components. Stern Pinball Inc (‘SELLER’) warrants only to the initial purchaser of its FCC CLASS A SUBPART J COMPLIANCE products that the items listed below are free from defects in material and... -
Page 59: Specifications
SPECIFICATIONS 7. SPECIFICATIONS SPECIFICATIONS, ENVIRONMENT SPECIFICATIONS, MECHANICAL, GAME SETUP Minimum Maximum Specification Imperial Metric Temperature, Operating 32 ℉ / 0 ℃ 104℉ / 40 ℃ Weight 210 lbs 96 kg Max dimensions, leg level- 78 x 27.75 x 57 in 198 x 70.5 x 145 cm Temperature, Storage 32 ℉... - Page 60 1-800-KICKERS WWE PRO MODEL #500-55G1-00 MANUAL PART #780-50G1-00 PARTS.SERVICE@STERNPINBALL.COM 02/12/15 EDITION WWW.STERNPINBALL.COM FACEBOOK.COM/STERNPINBALL...