Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Emerson PACSystems SLM042
Summary of Contents for Emerson PACSystems SLM042
- Page 1 User Guide GFK-3123A Jan 2020 PACSystems™ Ethernet Switch SLM042 Users Manual...
- Page 2 It is understood that Emerson may make changes, modifications, or improvements to the equipment referenced herein or to the document itself at any time. This document is intended for trained personnel familiar with the Emerson products referenced herein.
-
Page 3: Table Of Contents
PACSystems Ethernet Switch SLM042 User Manual Contents GFK-3123A Jan 2020 Contents Section 1: Getting to Know Your Switch ..............1 About the SLM042 Managed Ethernet Switch .............. 1 Software Features ....................... 1 Hardware Features ...................... 1 Section 2: Hardware Installation ................2 Installing Switch on DIN-Rail .................. - Page 4 PACSystems Ethernet Switch SLM042 User Manual Contents GFK-3123A Jan 2020 Port Control ....................26 5.4.3.1 5.4.4 Port Status ...................... 27 VLAN ......................... 27 5.5.1 VLAN Configuration – Port Based ..............27 5.5.2 SNMP Configuration ..................28 5.5.3 SNMP – Agent Setting ..................29 5.5.4 SNMP –Trap Setting ..................
-
Page 5: Getting To Know Your Switch
PACSystems Ethernet Switch SLM042 User Manual Section 1 GFK-3123A Jan 2020 Section 1: Getting to Know Your Switch About the SLM042 Managed Ethernet Switch The SLM042 series switches are cost-effect and powerful industrial switch with many features. These switches can work under wide temperature and dusty environment and humid condition. -
Page 6: Hardware Installation
PACSystems Ethernet Switch SLM042 User Manual Section 2 GFK-3123A Jan 2020 Section 2: Hardware Installation Installing Switch on DIN-Rail Each switch has a DIN-Rail kit on rear panel. The DIN-Rail kit helps switch to fix on the DIN- Rail. It is easy to install the switch on the DIN-Rail: 2.1.1 Mount SLM042 SERIES on DIN-Rail Figure 1: DIN-Rail Size... -
Page 7: Wall Mounting Installation
PACSystems Ethernet Switch SLM042 User Manual Section 2 GFK-3123A Jan 2020 Wall Mounting Installation Each switch has another installation method for users to fix the switch. A wall mount panel can be found in the package. The following steps show how to mount the switch on the wall: Figure 2: Wall-Mounting Size Hardware Installation... -
Page 8: Hardware Overview
PACSystems Ethernet Switch SLM042 User Manual Section 3 GFK-3123A Jan 2020 Section 3: Hardware Overview Front Panel The following table describes the labels that stick on the SLM042. Port Description 10/100 RJ-45 fast 10/100Base-T(X) RJ-45 fast Ethernet ports support auto- Ethernet ports negotiation. -
Page 9: Slm042 Series
PACSystems Ethernet Switch SLM042 User Manual Section 3 GFK-3123A Jan 2020 SLM042 Series Figure 3: Anatomy 1. LED for PWR1. When the PWR1 links, the green led will be light on. 2. LED for PWR2. When the PWR2 links, the green led will be light on. 3. -
Page 10: Front Panel Leds
PACSystems Ethernet Switch SLM042 User Manual Section 3 GFK-3123A Jan 2020 Front Panel LEDs Color Status Description DC power module 1 PWR1 Green activated. DC power module 2 PWR2 Green activated. PWR3 Green Power jack activated. Green Ring Master. Ring enabled. Slowly Ring Green... -
Page 11: Bottom Panel
PACSystems Ethernet Switch SLM042 User Manual Section 3 GFK-3123A Jan 2020 Bottom Panel The bottom panel components of SLM042 are showed as below: 1. Terminal block includes: PWR1, PWR2 (12-48V DC) and Relay output (1A@24VDC). 2. Power jack for PWR3 (12-45VDC). Figure 4: SLM042 Power Connection Hardware Overview... -
Page 12: Cables
PACSystems Ethernet Switch SLM042 User Manual Section 4 GFK-3123A Jan 2020 Section 4: Cables Ethernet Cables The SLM042 series switches have standard Ethernet ports. According to the link type, these switches use CAT 3, 4, 5,5e UTP cables to connect to any other network device (PCs, servers, switches, routers, or hubs). -
Page 13: Fibers
PACSystems Ethernet Switch SLM042 User Manual Section 4 GFK-3123A Jan 2020 The SLM042 series switches support auto MDI/MDI-X operation. You can use a straight- through cable to connect PC and switch. The following table below shows the 10BASE-T/ 100BASE-TX MDI and MDI-X port pin outs. MDI/MDI-X pins assignment Pin Number MDI port... -
Page 14: Web Management
PACSystems Ethernet Switch SLM042 User Manual Section 5 GFK-3123A Jan 2020 Section 5: Web Management WARNING While making any establishment and upgrading firmware, please remove physical loop connection first. Do NOT power off equipment while firmware is upgrading. Configuration by Web Browser This section introduces the configuration by Web browser. - Page 15 PACSystems Ethernet Switch SLM042 User Manual Section 5 GFK-3123A Jan 2020 3. The login screen appears. 4. Key in the username and password. The default username and password is “admin”. 5. Click “Enter” or “OK” button, then the main interface of the Web-based management appears.
-
Page 16: Basic Setting
PACSystems Ethernet Switch SLM042 User Manual Section 5 GFK-3123A Jan 2020 Basic Setting Figure 7: Switch Setting Interface The following table describes the labels in this screen. Label Description System Name Assign the name of switch. The maximum length is 64 bytes System Description Display the description of switch. -
Page 17: Admin Password
PACSystems Ethernet Switch SLM042 User Manual Section 5 GFK-3123A Jan 2020 5.2.1 Admin Password Change web management login username and password for the management security issue Figure 8: Change Password Admin Password interface The following table describes the labels in this screen. Label Description User name... -
Page 18: Ip Configuration
PACSystems Ethernet Switch SLM042 User Manual Section 5 GFK-3123A Jan 2020 5.2.2 IP configuration You can configure the IP Settings and DHCP client function through IP configuration. Figure 9: IP Configuration The following table describes the labels in this screen. Label Description DHCP Client... -
Page 19: Sntp Configuration
PACSystems Ethernet Switch SLM042 User Manual Section 5 GFK-3123A Jan 2020 5.2.3 SNTP Configuration The SNTP (Simple Network Time Protocol) settings allow you to synchronize switch clocks in the Internet. Figure 10: SNTP Configuration The following table describes the labels in this screen. Label Description SNTP Client... - Page 20 PACSystems Ethernet Switch SLM042 User Manual Section 5 GFK-3123A Jan 2020 Local Time Zone Conversion from UTC Time at 12:00 UTC November Time Zone - 1 hour 11 am Oscar Time Zone -2 hours 10 am ADT - Atlantic Daylight -3 hours 9 am AST - Atlantic Standard...
- Page 21 PACSystems Ethernet Switch SLM042 User Manual Section 5 GFK-3123A Jan 2020 BT - Baghdad, USSR Zone 2 +3 hours 3 pm ZP4 - USSR Zone 3 +4 hours 4 pm ZP5 - USSR Zone 4 +5 hours 5 pm ZP6 - USSR Zone 5 +6 hours 6 pm WAST - West Australian Standard...
-
Page 22: Lldp
PACSystems Ethernet Switch SLM042 User Manual Section 5 GFK-3123A Jan 2020 5.2.4 LLDP LLDP (Link Layer Discovery Protocol) function allows the switch to advertise its information to other nodes on the network and store the information it discovers. Figure 11: LLDP The following table describes the labels in this screen. - Page 23 PACSystems Ethernet Switch SLM042 User Manual Section 5 GFK-3123A Jan 2020 Figure 12: Backup and Restore The following table describes the labels in this screen. Label Description TFTP Server IP Address Fill in the TFTP server IP Restore File Name Fill the file name.
-
Page 24: Upgrade Firmware
PACSystems Ethernet Switch SLM042 User Manual Section 5 GFK-3123A Jan 2020 5.2.6 Upgrade Firmware Upgrade Firmware allows you to update the switch firmware. Before updating, make sure you have your TFTP server ready and the firmware image is on the TFTP server. Figure 13: Upgrade Firmware Redundancy 5.3.1... -
Page 25: Redundant Ring
PACSystems Ethernet Switch SLM042 User Manual Section 5 GFK-3123A Jan 2020 The following table describes the labels in this screen. Label Description Active Activate the fast recovery mode. Port Port can be configured as 6 priorities. Only the port with highest priority will be the active port. -
Page 26: Rstp
PACSystems Ethernet Switch SLM042 User Manual Section 5 GFK-3123A Jan 2020 The following table describes the labels in this screen. Label Description Redundant Ring Mark to enable Ring. There should be one and only one Ring Master in a ring. However if there are two or more switches which set Ring Ring Master Master to enable, the switch with the lowest MAC address will be... -
Page 27: Rstp Setting
PACSystems Ethernet Switch SLM042 User Manual Section 5 GFK-3123A Jan 2020 5.4.1 RSTP Setting You can enable/disable the RSTP function, and set the parameters for each port. Figure 16: RSTP Setting Web Management... - Page 28 PACSystems Ethernet Switch SLM042 User Manual Section 5 GFK-3123A Jan 2020 The following table describes the labels in this screen. Label Description RSTP mode You must enable or disable RSTP function before configuring the related parameters. Priority (0-61440) A value used to identify the root bridge. The bridge with the lowest value has the highest priority and is selected as the root.
-
Page 29: Rstp Information
PACSystems Ethernet Switch SLM042 User Manual Section 5 GFK-3123A Jan 2020 5.4.2 RSTP Information Show RSTP algorithm result at this table. Figure 17: RSTP Information RSTP Information interface Web Management... -
Page 30: Port Configuration
PACSystems Ethernet Switch SLM042 User Manual Section 5 GFK-3123A Jan 2020 5.4.3 Port Configuration 5.4.3.1 Port Control By this function, you can set the state, speed/duplex, flow control, and security of the port. Figure 18: Port Control The following table describes the labels in this screen. Label Description Port NO. -
Page 31: Port Status
PACSystems Ethernet Switch SLM042 User Manual Section 5 GFK-3123A Jan 2020 5.4.4 Port Status The following information provides the current port status. Figure 19: Port Status VLAN A Virtual LAN (VLAN) is a logical network grouping that limits the broadcast domain, which allows you to isolate network traffic. -
Page 32: Snmp Configuration
PACSystems Ethernet Switch SLM042 User Manual Section 5 GFK-3123A Jan 2020 Figure 20: Port-Based VLAN The following table describes the labels in this screen. Label Description Group Mark the blank to assign the port into VLAN group. Apply Click “Apply” to activate the configurations. Help Show help file. -
Page 33: Snmp - Agent Setting
PACSystems Ethernet Switch SLM042 User Manual Section 5 GFK-3123A Jan 2020 5.5.3 SNMP – Agent Setting You can set SNMP agent related information by Agent Setting Function. Figure 21: SNMP - Agent Setting The following table describes the labels in this screen. Label Description SNMP –... - Page 34 PACSystems Ethernet Switch SLM042 User Manual Section 5 GFK-3123A Jan 2020 Figure 22: SNMP - Trap Setting The following table describes the labels in this screen. Label Description Server IP The server IP address to receive Trap Community Community for authentication Trap Version Trap Version supports V1 and V2c.
-
Page 35: Snmp - Snmp-V3 Setting
PACSystems Ethernet Switch SLM042 User Manual Section 5 GFK-3123A Jan 2020 5.5.5 SNMP – SNMP-V3 Setting Figure 23: SNMP - V3 Setting Web Management... - Page 36 PACSystems Ethernet Switch SLM042 User Manual Section 5 GFK-3123A Jan 2020 The following table describes the labels in this screen Label Description Context Table Configure SNMP v3 context table. Assign the context name of context table. Click "Apply" to change context name User Table Configure SNMP v3 user table.
- Page 37 PACSystems Ethernet Switch SLM042 User Manual Section 5 GFK-3123A Jan 2020 Click "Remove" to remove unwanted context name. Access Table Configure SNMP v3 access table. Context Prefix: set up the context name. Group Name: set up the group. Security Level: select the access level. Context Match Rule: select the context match rule.
-
Page 38: System Warning
PACSystems Ethernet Switch SLM042 User Manual Section 5 GFK-3123A Jan 2020 System Warning Warning function is very important for managing switch. You can manage switch by SYSLOG, E-MAIL, and Fault Relay. It helps you to monitor the switch status on remote site. When events occurred, the warning message will send to your appointed server, E-MAIL, or relay fault to switch panel. -
Page 39: System Event Log
PACSystems Ethernet Switch SLM042 User Manual Section 5 GFK-3123A Jan 2020 5.6.2 System Event Log If system log client is enabled, the system event logs will show in this table. Figure 25: System Event Log The following table describes the labels in this screen. Label Description Page... -
Page 40: Smtp Setting
PACSystems Ethernet Switch SLM042 User Manual Section 5 GFK-3123A Jan 2020 5.6.3 SMTP Setting The SMTP is Short for Simple Mail Transfer Protocol. It is a protocol for e-mail transmission across the Internet. Please refer to RFC 821 - Simple Mail Transfer Protocol. Figure 26: SMTP Setting The following table describes the labels in this screen. -
Page 41: Event Selection
PACSystems Ethernet Switch SLM042 User Manual Section 5 GFK-3123A Jan 2020 5.6.4 Event Selection SYSLOG and SMTP are the two warning methods that supported by the system. Check the corresponding box to enable system event warning method you wish to choose. Please note that the checkbox cannot be checked when SYSLOG or SMTP is disabled. -
Page 42: Fault Relay Alarm
PACSystems Ethernet Switch SLM042 User Manual Section 5 GFK-3123A Jan 2020 Help Show help file. 5.6.5 Fault Relay Alarm When any selected fault event is happened, the Fault LED in switch panel will light up and the electric relay will signal at the same time. Figure 28: Fault Relay Alarm Save Configuration If any configuration changed, “Save Configuration”... -
Page 43: Factory Default
PACSystems Ethernet Switch SLM042 User Manual Section 5 GFK-3123A Jan 2020 5.7.1 Factory Default Figure 30: Factory Default Reset switch to default configuration. Click to reset all configurations to the default value. You can select “Keep current IP address setting” and “Keep current username &... -
Page 44: Technical Specifications
PACSystems Ethernet Switch SLM042 User Manual Section 6 GFK-3123A Jan 2020 Section 6: Technical Specifications Switch Model IC086SLM042MM IC086SLM042SS Physical Ports Number of Port 10/100Base-T(X) RJ45 Ports 100Base-FX Fiber Ports Fibre Mode Multi Mode Single Mode Technology IEEE 802.3 for 10Base-T IEEE 802.3 for 10Base-T IEEE 802.3u for 100Base-TX and IEEE 802.3u for 100Base-TX... - Page 45 PACSystems Ethernet Switch SLM042 User Manual Section 6 GFK-3123A Jan 2020 Switch Model IC086SLM042MM IC086SLM042SS SNMP v1/v2c/v3 and private MIB Port configuration, status, support statistics, monitoring, security SNMP v1/v2c/v3 and private MIB support RSTP Network Redundancy RSTP Fast Recovery ,Redundant Fast Recovery ,Redundant Ring Ring Relay output for fault event...
- Page 46 PACSystems Ethernet Switch SLM042 User Manual Section 6 GFK-3123A Jan 2020 Switch Model IC086SLM042MM IC086SLM042SS Operating Temperature -40~70℃ -40~70℃ Operating Humidity 5% to 95% Non-condensing 5% to 95% Non-condensing Regulatory Approvals FCC Part 15, CISPR (EN55022) class A EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS), EN61000- 4-8, EN61000-4-11...
- Page 48 Note: If the product is purchased through an Authorized Channel Partner, please contact the seller directly for any support. Emerson reserves the right to modify or improve the designs or specifications of the products mentioned in this manual at any time without notice. Emerson does not assume responsibility for the selection, use or maintenance of any product.