Summary of Contents for Agora Models Lamborghini MIURA
Page 1
Pack 10 B U I L D I N S T R U C T I O N S STAGE 75: INSTALLING THE FUEL PUMPS AND STAGE 79: AT TACHING THE LEFT THE FRONT FRAME REINFORCEMENT PLATES AND RIGHT DOORS STAGE 76: FIT TING THE DASHBOARD STAGE 80: BUILDING THE BONNET AND FRONT FRAME INTO THE BODY AND...
Page 2
WARNING: Some parts are assembled using magnets. These magnets can cause serious injury if they are swallowed. Keep away from children. If you suspect a magnet has been swallowed, seek medical help straight away. AGORAMODELS LAMBORGHINI MIURA...
Page 3
Front frame reinforcement plate (left) Long tube x2 Short tube x4 Fuel pump (1) Fuel pump (2) Fuel pump bracket Fitting x2 Front frame reinforcement plate (left) Front frame reinforcement plate (right) Long tube x2 Short tube x4 AGORAMODELS LAMBORGHINI MIURA...
Page 4
Ensure that the parts are oriented as shown in the inset photo, with the pins on the back of the bracket (blue arrow) on the right while the flat ends of the fuel pumps (red arrows) are oriented upwards. AGORAMODELS LAMBORGHINI MIURA...
Page 5
(red arrows). The other pair fits onto the bottom pins as shown. reinforcement plate. To do this, insert the pins of the pump bracket into the two holes on the plate (red arrows). Note that the rounded ends (blue arrows) of the fuel pumps are oriented upwards. AGORAMODELS LAMBORGHINI MIURA...
Page 6
You may wish to remove then place the tube in hot water first to bend it into shape. S T A G E C O M P L E T E AGORAMODELS LAMBORGHINI MIURA...
Page 7
Upper tie rod x2 Circuit board Steering joint Type Q screws x2 Type A screws x15 Type B screws x8 Upper tie rod x2 Circuit board Steering joint Type Q x2 Type A x15 Type B x8 AGORAMODELS LAMBORGHINI MIURA...
Page 8
Turn the dashboard upside down. Opposite the steering wheel there windscreen area, there are three drilled columns on each side: the two are two slots (arrows) for fixing it to the body. innermost columns (arrows) are for installing the dashboard. AGORAMODELS LAMBORGHINI MIURA...
Page 9
TYPE A Secure the right-hand side of the dashboard with a Type A screw. Check that the dashboard is fitted flush all the way round. AGORAMODELS LAMBORGHINI MIURA...
Page 10
There is a large rectangular opening in the Make sure to orient the card so that the connectors numbered 5 to 8 center with four perforated columns (circled) inside for fixing the are facing the rear of the assembly (arrow). electronic board. AGORAMODELS LAMBORGHINI MIURA...
Page 11
– be careful not to apply too much force to any of the plastic areas of the model. You may wish to file excess black paint from the faces of the side connections (arrows) where they contact the body. AGORAMODELS LAMBORGHINI MIURA...
Page 12
Drive the second Type A screw into the passenger side slot. positioned correctly, you can fix everything with four Type A screws. Start inserting the first one in the slot on the driver’s side, located next to the dashboard fixing point. AGORAMODELS LAMBORGHINI MIURA...
Page 13
– the ends of the steering columns should look like those in the image. Connect the two steering columns together by pressing the pin of one into the hole of the other (arrow). AGORAMODELS LAMBORGHINI MIURA...
Page 14
The steering wheel may turn a small amount both left and right before the columns begins to turn the wheels. S T A G E C O M P L E T E AGORAMODELS LAMBORGHINI MIURA...
S T A G E 7 7 P A R T S L I S T Name Bonnet inner bulkhead Bonnet side crossbar Bonnet side crossbar Bonnet central crossbar Type B screws x3 Bonnet inner bulkhead Bonnet side crossbar Bonnet side crossbar Bonnet central crossbar Type B x3 AGORAMODELS LAMBORGHINI MIURA...
Page 16
– be crossmember of the frame (dashed line). careful to align the plug correctly with the pins of the circuit board connection so as not to bend them. AGORAMODELS LAMBORGHINI MIURA...
Page 17
Take the instrument panel LED wire, which is white with red/black Plug the instrument panel LED into connection 7 (arrow). cables, and route it under the crossmember. AGORAMODELS LAMBORGHINI MIURA...
Page 18
Retrieve the cockpit assembly and place it on your work surface. There At the rear of the cockpit, below the headrests, there are two more are two holes on the front for fixing it to the body (arrows). holes for fixing (arrows). AGORAMODELS LAMBORGHINI MIURA...
Page 19
9 align with the connection points highlighted with the red arrows in as shown (arrows). The connections are delicate – take care when step 11. inserting the cockpit the wires don’t snag or bend out of place. AGORAMODELS LAMBORGHINI MIURA...
Page 20
TYPE A Use another Type A screw (supplied with Stage 76) to secure the Take the plug of the accelerator switch (black plug, white panel). right-hand side of the cockpit in the same manner. AGORAMODELS LAMBORGHINI MIURA...
Page 21
Stage 77: Connecting the Wiring and Fitting the Cockpit into the Body Plug the accelerator switch into connection 3 (arrow). Next take the brake switch (black plug, green panel). Plug the brake switch into connection 13 (arrow). Now take the engine switch (black plug). AGORAMODELS LAMBORGHINI MIURA...
Page 22
Plug the engine switch into connection 6 (arrow). Finally, take the interior light switch (white plug, red panel). Route the cable under the crossmember if not done so already. Plug the interior light into connection 16 (arrow). AGORAMODELS LAMBORGHINI MIURA...
Page 23
Stage 77: Connecting the Wiring and Fitting the Cockpit into the Body S T A G E C O M P L E T E AGORAMODELS LAMBORGHINI MIURA...
Right support Left support Right perforated plate Left perforated plate Type A screws x3 Type B screws x7 Bonnet reinforcement frame Right support Left support Left perforated plate Right perforated plate Type A x3 Type B x7 AGORAMODELS LAMBORGHINI MIURA...
Page 25
(arrows). Align the body and the rear frame assemblies with each other as shown. Connect the two together by fitting the fixing points highlighted in steps 1 and 2. AGORAMODELS LAMBORGHINI MIURA...
Page 26
Check the holes for fixing are aligned (circled). TYPE A TYPE A Starting on the driver’s side, drive one of the Type A screws into the Drive another of the Type A screws into the trapezoid-shaped trapezoid-shaped connection. connection on the passenger’s side. AGORAMODELS LAMBORGHINI MIURA...
Page 27
Type A screw. body (arrow) to ensure the holes are aligned as you drive the screw in. The assembly should look like this once the rear frame has been fixed to the body. AGORAMODELS LAMBORGHINI MIURA...
Page 28
Carefully flex the right rod from the middle and guide its triangular Repeat with the other rod in the same manner. You can see the end into the slot located on the rear frame (arrow). Note the nut facing hexagonal bolt head is facing outwards (circled). inwards (circled). AGORAMODELS LAMBORGHINI MIURA...
Page 29
Stage 78: Fitting the Rear Frame and Installing the Upper Tie Rods S T A G E C O M P L E T E AGORAMODELS LAMBORGHINI MIURA...
Page 30
Support plate x2 Headlight housing Headlight lens Type B screws x3 Headlight lens Headlight LED Headlight LED Headlight support Headlight housing Headlight housing Support plate x2 Headlight lens Headlight lens Type B x3 Headlight LED Headlight LED AGORAMODELS LAMBORGHINI MIURA...
Page 31
Start to secure the door using 2x Type A screws (supplied with Stage 76), but don’t fully tighten the screws yet. Note the wire of the door switch has been threaded through the lower part of the frame (arrow). AGORAMODELS LAMBORGHINI MIURA...
Page 32
(arrows) and lay them between the front frame and the cockpit as shown, then pass the plugs under the front cross member towards the circuit board. Take care not to damage the pedal connections (circled) as you lay the left-hand door wire in place. AGORAMODELS LAMBORGHINI MIURA...
Page 33
First take the right door switch with a white plug and blue panel. Plug the right door switch into connection 15 (arrow). Take the plug of the left door switch, which is white (no panel colour). Plug the left door switch into connection 14 (arrow). AGORAMODELS LAMBORGHINI MIURA...
Page 34
Stage 79: Attaching the Left and Right Doors S T A G E C O M P L E T E AGORAMODELS LAMBORGHINI MIURA...
Page 35
Stage 77 to begin building the reinforcement structure for supporting the front body. S T A G E 8 0 P A R T S L I S T Name Front body Type Q screws x3 Front body Type Q x3 AGORAMODELS LAMBORGHINI MIURA...
Page 36
(circled). Note the small and large hole for fitting the inner bulkhead that correspond with the small pin and large column (blue arrows). AGORAMODELS LAMBORGHINI MIURA...
Page 37
(blue arrow) which runs around the length the pins and column into the side crossbar in the same manner as and height of the front should face towards the inner bulkhead. before (arrows). AGORAMODELS LAMBORGHINI MIURA...
Page 38
Stage 80: Building the Bonnet Reinforcement Structure (1) TYPE B Drive a Type B screw into the column of the inner bulkhead to fix the parts together. S T A G E C O M P L E T E AGORAMODELS LAMBORGHINI MIURA...
Page 39
Type S screws x2 Type A screws x3 Type G screws x5 Bonnet support bracket x2 Internal frame detail Rear bonnet hinge x2 Bonnet grille support Front bonnet hinge x2 Type S x2 Type A x3 Type G x5 AGORAMODELS LAMBORGHINI MIURA...
Page 40
Fit the right support into the other side of the frame in the same Make sure the screw is flush with the support. manner and secure it using a Type B screw, making sure it is flush. AGORAMODELS LAMBORGHINI MIURA...
Page 41
Use 2x Type B screws (supplied with Stage 78) to secure the other side. Take the right and left perforated plates (supplied with Stage 78) and press them together, using the pins and columns (arrows). Note the pin at the end of the perforated plates (inset, circled). AGORAMODELS LAMBORGHINI MIURA...
Page 42
Press the pin of the plates into the inner bulkhead as shown. the perforated plates fits into the rectangular hole in the middle of the inner bulkhead (arrow). S T A G E C O M P L E T E AGORAMODELS LAMBORGHINI MIURA...
Page 43
S T A G E 8 2 P A R T S L I S T Name Left front wheel arch Left front fog light lens Left front fog light body Left front indicator Left front wheel arch Left front indicator Left front Left front fog light fog light body lens AGORAMODELS LAMBORGHINI MIURA...
Page 44
(inset). The fit The headlights are now ready to be mounted onto the support. may be tight, we recommend holding behind the bulb with a pair of tweezers to firmly press it into place. AGORAMODELS LAMBORGHINI MIURA...
Page 45
Mount one of the headlights onto one end of the support, then secure Mount the other headlight in the same manner and secure it using a it using a Type B screw (supplied with Stage 79). Type B screw. AGORAMODELS LAMBORGHINI MIURA...
Page 46
Stage 82: Assembling the Headlights S T A G E C O M P L E T E AGORAMODELS LAMBORGHINI MIURA...
Need help?
Do you have a question about the Lamborghini MIURA and is the answer not in the manual?
Questions and answers